Available 4 files for Digital Research DRSound3D-ALS100+
Select Files
Company
Digital Research
Categories
Sound Card & Multimedia & MP3
Model
Digital Research DRSound3D-ALS100+
Description
DRSound-OPTI 931
Operating System
MS-Dos-Windows 3.1
Size Driver
724KB
File Name
drsdals1.exe
Observations
DOS and Windows 3.1 Installation for ALS100+:
============================================
[SETUP.EXE for Windows 3.1]
The SETUP.EXE is a Windows 3.1 setup program that installs DOS and Windows
3.1 drivers and utilities.
The user can run SETUP.EXE by selecting File|Run... and typing "A:SETUP" on
the command line under Windows 3.1 Program Manager, or by typing "A:SETUP" at
DOS prompt if Windows directory is in the PATH. The SETUP.EXE copies all the
DOS drivers and utilities to the directory that user specifies during the
setup program. All the Windows 3.1 drivers and VxDs are copied to the
Windows system directory. When the user installs the Avance Sound System
for the first time the A3CONFIG.EXE is started to configure the board setting
after the Setup program is finished.
[DOSINST.EXE for DOS Only installation]
The DOSINST.EXE is a DOS installation program that copies all the DOS drivers
and utilities to the directory that user specifies. When the user installs
the Avance Sound System for the first time the A3CONFIG.EXE is started to
configure the board setting after the Setup program is finished. DOSINST.EXE
can be installed by typing A:DOSINST.EXE at the DOS prompt.
Windows 95 installation procedure for ALS100+:
=============================================
1. After user installs the ALS100+ sound card into the ISA slot in the computer
and powers on the system, Windows 95 will prompt user with a "New Hardware
Found" dialog box since the ALS100+ sound card is ISA plug and play.
To install the Windows 95 drivers, select "Driver from disk provided by
hardware manufacturer" and click on OK.
2. Insert the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" diskette into
the appropriate drive and select that drive from the prompted dialog box
and click on OK. Windows 95 will copy all the needed files and set up all
the logic devices on the board automatically.
3. Install the ALSRACK player by running the SETUP.EXE file (also provided
on the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" disk) from the
Windows 95 Start menu|Run. This will create the Avance Sound Program
Group with the ALSRACK utility icon.
(See Appendix below for full descr of ALSRACK functions).
Troubleshooting:
================
This appendix provides some tips and information for some of the
problems you might encounter with your ALS100+ sound card either during
installation or normal use.
[Problems in DOS]
Problem: Cannot load IDE CD-ROM drive.
Cause: IDE port is not enabled. Check the config.sys file under
C: root directory and you should see "device=c:\a3sound
\cdsetup.sys /P:xxx" before loading your CD-ROM driver.( xxx
is the base port of the sound card ). The cdsetup.sys
enables the IDE port.
Solution: Run C:\A3SOUND\A3CONFIG.EXE again and select the CD-ROM
IDE. When you leave the a3config program, device=c:\a3sound
\cdsetup.sys /P:xxx will be added to config.sys. Make sure
that this line is added before loading the CD-ROM driver.
Problem: No sound in a DOS application
Cause: There could be conflicts in the SB16 settings.
Solution: Rerun the C:\A3SOUND\A3CONFIG.EXE and try another Port,
DMA, or IRQ.
Company
Digital Research
Categories
Sound Card & Multimedia & MP3
Model
Digital Research DRSound3D-ALS100+
Description
DRSound-OPTI 931
Operating System
Windows 95
Size Driver
724KB
File Name
drsdals1.exe
Observations
DOS and Windows 3.1 Installation for ALS100+:
============================================
[SETUP.EXE for Windows 3.1]
The SETUP.EXE is a Windows 3.1 setup program that installs DOS and Windows
3.1 drivers and utilities.
The user can run SETUP.EXE by selecting File|Run... and typing "A:SETUP" on
the command line under Windows 3.1 Program Manager, or by typing "A:SETUP" at
DOS prompt if Windows directory is in the PATH. The SETUP.EXE copies all the
DOS drivers and utilities to the directory that user specifies during the
setup program. All the Windows 3.1 drivers and VxDs are copied to the
Windows system directory. When the user installs the Avance Sound System
for the first time the A3CONFIG.EXE is started to configure the board setting
after the Setup program is finished.
[DOSINST.EXE for DOS Only installation]
The DOSINST.EXE is a DOS installation program that copies all the DOS drivers
and utilities to the directory that user specifies. When the user installs
the Avance Sound System for the first time the A3CONFIG.EXE is started to
configure the board setting after the Setup program is finished. DOSINST.EXE
can be installed by typing A:DOSINST.EXE at the DOS prompt.
Windows 95 installation procedure for ALS100+:
=============================================
1. After user installs the ALS100+ sound card into the ISA slot in the computer
and powers on the system, Windows 95 will prompt user with a "New Hardware
Found" dialog box since the ALS100+ sound card is ISA plug and play.
To install the Windows 95 drivers, select "Driver from disk provided by
hardware manufacturer" and click on OK.
2. Insert the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" diskette into
the appropriate drive and select that drive from the prompted dialog box
and click on OK. Windows 95 will copy all the needed files and set up all
the logic devices on the board automatically.
3. Install the ALSRACK player by running the SETUP.EXE file (also provided
on the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" disk) from the
Windows 95 Start menu|Run. This will create the Avance Sound Program
Group with the ALSRACK utility icon.
(See Appendix below for full descr of ALSRACK functions).
Troubleshooting:
================
This appendix provides some tips and information for some of the
problems you might encounter with your ALS100+ sound card either during
installation or normal use.
[Problems in DOS]
Problem: Cannot load IDE CD-ROM drive.
Cause: IDE port is not enabled. Check the config.sys file under
C: root directory and you should see "device=c:\a3sound
\cdsetup.sys /P:xxx" before loading your CD-ROM driver.( xxx
is the base port of the sound card ). The cdsetup.sys
enables the IDE port.
Solution: Run C:\A3SOUND\A3CONFIG.EXE again and select the CD-ROM
IDE. When you leave the a3config program, device=c:\a3sound
\cdsetup.sys /P:xxx will be added to config.sys. Make sure
that this line is added before loading the CD-ROM driver.
Problem: No sound in a DOS application
Cause: There could be conflicts in the SB16 settings.
Solution: Rerun the C:\A3SOUND\A3CONFIG.EXE and try another Port,
DMA, or IRQ.
Company
Digital Research
Categories
Sound Card & Multimedia & MP3
Model
Digital Research DRSound3D-ALS100+
Description
DRSound-OPTI 931
Operating System
Windows 98
Size Driver
724KB
File Name
drsdals1.exe
Observations
DOS and Windows 3.1 Installation for ALS100+:
============================================
[SETUP.EXE for Windows 3.1]
The SETUP.EXE is a Windows 3.1 setup program that installs DOS and Windows
3.1 drivers and utilities.
The user can run SETUP.EXE by selecting File|Run... and typing "A:SETUP" on
the command line under Windows 3.1 Program Manager, or by typing "A:SETUP" at
DOS prompt if Windows directory is in the PATH. The SETUP.EXE copies all the
DOS drivers and utilities to the directory that user specifies during the
setup program. All the Windows 3.1 drivers and VxDs are copied to the
Windows system directory. When the user installs the Avance Sound System
for the first time the A3CONFIG.EXE is started to configure the board setting
after the Setup program is finished.
[DOSINST.EXE for DOS Only installation]
The DOSINST.EXE is a DOS installation program that copies all the DOS drivers
and utilities to the directory that user specifies. When the user installs
the Avance Sound System for the first time the A3CONFIG.EXE is started to
configure the board setting after the Setup program is finished. DOSINST.EXE
can be installed by typing A:DOSINST.EXE at the DOS prompt.
Windows 95 installation procedure for ALS100+:
=============================================
1. After user installs the ALS100+ sound card into the ISA slot in the computer
and powers on the system, Windows 95 will prompt user with a "New Hardware
Found" dialog box since the ALS100+ sound card is ISA plug and play.
To install the Windows 95 drivers, select "Driver from disk provided by
hardware manufacturer" and click on OK.
2. Insert the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" diskette into
the appropriate drive and select that drive from the prompted dialog box
and click on OK. Windows 95 will copy all the needed files and set up all
the logic devices on the board automatically.
3. Install the ALSRACK player by running the SETUP.EXE file (also provided
on the "ALS100+ DOS/Win3.1/Win 95 Drivers and Utilities" disk) from the
Windows 95 Start menu|Run. This will create the Avance Sound Program
Group with the ALSRACK utility icon.
(See Appendix below for full descr of ALSRACK functions).
Troubleshooting:
================
This appendix provides some tips and information for some of the
problems you might encounter with your ALS100+ sound card either during
installation or normal use.
[Problems in DOS]
Problem: Cannot load IDE CD-ROM drive.
Cause: IDE port is not enabled. Check the config.sys file under
C: root directory and you should see "device=c:\a3sound
\cdsetup.sys /P:xxx" before loading your CD-ROM driver.( xxx
is the base port of the sound card ). The cdsetup.sys
enables the IDE port.
Solution: Run C:\A3SOUND\A3CONFIG.EXE again and select the CD-ROM
IDE. When you leave the a3config program, device=c:\a3sound
\cdsetup.sys /P:xxx will be added to config.sys. Make sure
that this line is added before loading the CD-ROM driver.
Problem: No sound in a DOS application
Cause: There could be conflicts in the SB16 settings.
Solution: Rerun the C:\A3SOUND\A3CONFIG.EXE and try another Port,
DMA, or IRQ.
Company
Digital Research
Categories
Sound Card & Multimedia & MP3
Model
Digital Research DRSound3D-ALS100+
Description
DRSound-OPTI 931
Operating System
Windows NT
Size Driver
99KB
File Name
drsdal1n.exe
Observations
Windows NT installation procedure for ALS200:
1. Insert the "ALS200 Windows NT Drivers and Utilities" diskette
into drive A:, and within CONTROL PANEL/DRIVERS/ADD/UNLISTED OR UPDATED
DRIVER, choose "OK". While installing, "Driver Exists" warning message
will appear and will ask to keep the old "midimap.cfg" or re-install.
Please choose re-install, or else midi will not function properly.
For Winnt4.0 installation procedure for ALS200:
1. Insert the "ALS200 Windows NT Drivers and Utilities" diskette
into drive A: or B:, and within CONTROL PANEL/MULTIMEDIA/DEVICE/ADD,
choose "OK". While installing, "Driver Exists" warning message will
appear and will ask to keep the old or re-install. Please choose
re-install, or else it will not funtion properly.
Access to Official Website Digital Research
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.