Available 2 files for Exsys EX-44044
Select Files
Company
Exsys
Categories
Other Peripherals
Model
Exsys EX-44044
Description
PCI-Express 4S Serial RS-232 card (Moschip)
Information
Manual
Operating System
Manual
Size Driver
307KB
File Name
ex-44044.pdf
Observations
HARDWARE INSTALLATION :
Attention! Do not install the card before running the setup utility. Please install
the drivers for the card first. If not the card might not be installed correctly!!! If
you already do install the drivers please proceed with the following Instructions.
If you are ready with the jumper settings, please proceed with the following installation
instructions. Because the designs of computers are different, only general installation
instructions are given. Please refer your computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Computer
and gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of your
computer. Make sure it is the right expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make
sure the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer’s cover and the mounting screws.
DRIVER INSTALLATION :
Windows 2000/XP & Server 2003 32-Bit:
Please insert the driver CD into your CD-Rom drive (for example D:\ ) and open the
folder D:\IO\MOSCHIP\MCS9901\XP32_2K_2003 on the CD.
Now start the file “PCIeSetup32.exe“ by double click on it and follow the setup program
to finish installation process. After that shut down windows and follow the instructions for
the Hardware installation. After installing the card simply start your computer and the
card will be recognized automatically by your system.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows
that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find
one more new ”PCI Ports“ as sample (COM3). If you see this or similar entries the card
is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number COM 3 to COM5, open the >Device Manager< click
at >COM3<, >Settings< and then >Advance<. There you can choose from COM 3 to 256.
Windows XP/Server 2003 64-Bit:
Please insert the driver CD into your CD-Rom drive (for example D:\ ) and open the
folder D:\IO\MOSCHIP\MCS9901\XP64 on the CD.
Now start the file “PCIeSetup64.exe“ by double click on it and follow the setup program
to finish installation process. After that shut down windows and follow the instructions for
the Hardware installation. After installing the card simply
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows
that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find
one more new ”PCI Ports“ as sample (COM3). If you see this or similar entries the card
is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number COM 3 to COM5, open the >Device Manager< click
at >COM3<, >Settings< and then >Advance<. There you can choose from COM 3 to 256.
Windows Vista 32-Bit:
Please insert the driver CD into your CD-Rom drive (for example D:\ ) and open the
folder D:\IO\MOSCHIP\MCS9901\Vista32 on the CD.
Now start the file “PCIeSetup32.exe“ by double click on it and follow the setup program
to finish installation process. After that shut down windows and follow the instructions for
the Hardware installation. After installing the card simply start your computer and the
card will be recognized automatically by your system.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows
that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find
one more new ”PCI Ports“ as sample (COM3). If you see this or similar entries the card
is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number COM 3 to COM5, open the >Device Manager< click
at >COM3<, >Settings< and then >Advance<. There you can choose from COM 3 to 256.
Company
Exsys
Categories
Other Peripherals
Model
Exsys EX-44044
Description
PCI-Express 4S Serial RS-232 card (Moschip)
Operating System
MS-DOS-Windows 98-98Se-Me-NT4-2000-XP-2003-Vista-Linux
Size Driver
6MB
File Name
ex-44044.zip
Observations
Windows Vista 32 / 64 bit User Manual
Revision 0.1
Table of Contents
1. INTRODUCTION 2
2. OBTAINING DRIVER 2
3. DRIVER INSTALLATION 2
4. VERIFYING DRIVER INSTALLATION 5
5. SERIAL PORT PROPERTIES SHEET: 5
6. SERIAL PORT FEATURES AND MODE CHANGES: 9
7. DIRECT MEMORY ACCESS (DMA): 14
8. PARALLEL PORT FEATURES AND MODE CHANGES: 15
9. USB MODE: 16
10. UNINSTALLING DRIVERS: 16
11. SUGGESTIONS / SUPPORT: 17
=========================================================================
DOS Driver Installation User Manual
Table of Contents
1. Description:........................................................................................................................................1
2. Contents available with Moschip DOS Driver Disk:........................................................................1
3. Options:..............................................................................................................................................1
4. Installation Procedure:.....................................................................................................................2
5. Loop back connections:...................................................................................................................6
Revision history.........................................................................................................................................6
1. Description:
This document provides the information about how to install the serial and parallel drivers for MosChip MCS9901 PCIe to Serial and Parallel I/O ports on DOS 6.22 environment. Normally any serial and parallel I/O ports can be supported by BIOS call services in DOS environment. However DOS supports only 4 serial ports and 3 parallel ports.
Access to Official Website Exsys
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.