Clevo 8700 Notebooks & Tablet PCs > Downloads Drivers, Utilities and Manual

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

TEAC CD-224E-A CDROM Drivers

Size Driver

652KB

File Name

teaccd.zip

Observations

***** How to install the device driver under DOS environment *****

To operate TEAC CD-ROM,the device driver (TEAC_CDI.SYS) has to be installed
from INSTALLATION DISK came along with CD-ROM.
Please follow the instruction below.

1. Boot up the system and insert the INSTALLATION DISK into your floppy
disk drive.

2. At the DOS prompt,type "A:\INSTALL" then press enter. (If your floppy
disk drive is "A:")

3. Installation program will now start.Please follow the instructions on the
screen to complete the installation procedure.

4. When finish,remove the INSTALLATION DISK from the floppy disk drive then
REBOOT your system.

During system reboot,check for the following message to assure that
the driver was loaded properly.

MSCDEX Version 2.23
Copyright (C) Microsoft Corp. 1986-1993. All rights reserved.

Drive X: = Driver TEAC-CDI unit 0

* 'X:' ... Drive letter assigned to CD-ROM Drive

This message means that TEAC CD-ROM drive is now activated.

* Now the installation of TEAC CD-ROMdrive is completed.
***** TEAC CD-ROM DRIVE Trouble Shooting Tips *****

------------------------------------------------------------------------------
Q1: System will not boot when CD-ROM drive is daisy-chained with
hard disk drive.
------------------------------------------------------------------------------
A1: Be sure your hard disk drive jumper is set to MASTER and CD-ROM's to SLAVE.
Please refer to the installation manual for CD-ROM jumper setting and ask
hard drive manufacturer for MASTER jumper setting.
Note: There may be a case where CD-ROM can not be daisy-chained with
Conner hard drive (Conner mode).
A2: Check if the I/F cable is connected reversely.

------------------------------------------------------------------------------
Q2: System hangs without displaying anything when the device driver is loaded
during Boot-up.
------------------------------------------------------------------------------
A1:There is a possibility that TEAC device driver is having a conflict with
others. Please check the position of the device driver statement or remark
driver which may be having a conflict with.
A2:In case that TEAC CD-ROM drive is connected with non TEAC CD-ROM drive in
the same system.
Please re-install the TEAC CD-ROM address by going through 'SELECT I/O PORT'.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

VGA

Operating System

OS/2

Size Driver

1.2MB

File Name

8xvgaos2.exe

Observations

OS/2 Video Device Driver for Chips And Technologies
65550 Flat Panel/CRT Graphics Accelerator

1.0 Compatibility
-----------------
This driver is designed to function with OS/2 Version 2.11 and OS/2 3.0 Warp
operating systems.

2.0 Hardware
------------
These drivers support Chips And Technologies 65550 Flat Panel/CRT
graphics accelerator adapters in a PCI Bus configuration.

3.0 Supported Features
----------------------
This graphics accelerator driver is designed to function as a 32-bit
Presentation Manager graphics display driver under the OS/2 32 bit graphics
engine, and provides Seamless Windows 3.1 support.

This display driver also supports setting the CRT screen refresh rate using
the System-Settings notebook in the OS/2 System Setup folder.

3.1 Supported Resolutions
-------------------------
Supported resolutions are provided based on availablity in Video BIOS. Not all
systems have all resolutions provided, and may be display mode ( LCD/Simul/CRT )
dependent.

8 Bit/Pixel 640x480x256, 800x600x256, 1024x768x256
16 Bit/Pixel 640x480x64K, 800x600x64K, 1024x768x64K
24 Bit/Pixel 640x480x16M

4.0 Driver Installation
-----------------------

4.1 Preliminary Steps
---------------------
The following steps must be performed before you install the 65550/554
display driver:

1. OS/2 DOS Support must be installed.

2. If you previously installed SVGA support, you must reset the system
to VGA mode. VGA is the default video mode enabled when OS/2 is installed.
To restore VGA mode, use Selective Install and select VGA for Primary
Display. For more information on this procedure, see the section on
Changing Display Adapter Support in the OS/2 Users Guide.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

Audio Drivers

Operating System

OS/2

Size Driver

320KB

File Name

85audos2.exe

Observations

ESS Technology is providing OS/2 drivers for the ES1879
AudioDrive chip in this Software Release.

This document provides:

- a description of the changes to the drivers

- installation notes

Please read this document completely before you upgrade your
system, and follow the instructions carefully.

Release Information

Product: ES1879 AudioDrive OS/2 Device Driver,
Version 2.12

Drivers: ES1879 (with ESFM and wavetable)

OS: OS/2 Warp 4.0 and OS/2 Warp 3.0

Release Date: July 18, 1997

Release Description

The ES1879 AudioDrive OS/2 Driver Software Release incorporates
the following features.
Version 2.12 Features

ES938 support

An application, SPATIAL.EXE, is provided to control ES938 3D
Stereo Processor or the built-in Spatializer.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

PCMCIA

Operating System

Windows 3.1

Size Driver

1.1MB

File Name

85pcmcia31.zip

Observations

SystemSoft's CardWizard(TM)
Version 5.3
The Intelligent PCMCIA Configuration Utility
______________________________________________

===============
README Contents
===============

CardWizard Requirements
CardWizard Installation
Instructions
CONFIG.SYS Menu Partitions
Notes About Your CardWizard Software
Flash Support Update
CardWizard Release Notes
Note on Advanced Power Management (CS_APM.EXE)
Note on LAN Cards
Note on Token Ring Cards
Note on Docking Stations
Sony CD-Rom
Madge Token Ring
Ositech Trump Card
SMC Ethernote Card
Xircom Token Ring

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

VGA

Operating System

Windows 3.1

Size Driver

913KB

File Name

8xvgaw31.exe

Observations

Chips & Technologies, Inc.

DR655xx Display Driver Package
Release Notes for Windows 3.X

=======================================================================
Revision: Production Version 1.3.0 , 6555X
Release Date: April 17, 1997
=======================================================================

1. General driver release.

2. CHIPSCPL - Added 68554 and 68555 support.

=======================================================================
Revision: Production Version 1.2.9 , 6555X
Release Date: April 09, 1997
=======================================================================

1. General driver release.

2. VDD #335 bug fix release. The problem resolved - Switches to
CRT mode when DOS box is opened.

3. Bug fix for problem #297 .
When both Background and Exclusive were being set with
PIF editor for DOS Full Screen, the screen would go blank when
going to full screen from Win or DOS box.

=======================================================================
Revision: Production Version 1.2.8 , 6555X
Release Date: April 08, 1997
=======================================================================

1. IBM Japanese Windows release.
2. Specialized VDD required:
Added built-in Japanese support from IBM for IBM Windows 3.1J .
This VDD requires Japanese grabber and VDDD386 and DPGRAB.DLL
are not used.

=======================================================================
Revision: Production Version 3.3.3 , 65548/65545
Release Date: April 07, 1997
=======================================================================

1. VDD #335 bug fix release. The problem resolved - Switches to
CRT mode when DOS box is opened.

2. Added built-in Japanese support from IBM for IBM Windows 3.1J .
This VDD requires Japanese grabber (CHIP55XJ.3GR).
VDDD386 and DPGRAB.DLL are not used.

3. Bug fix for problem #297 .
When both Background and Exclusive were being set with
PIF editor for DOS Full Screen, the screen would go blank when
going to full screen from Win or DOS box.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

Video In under

Operating System

Windows 95

Size Driver

42KB

File Name

videoin.exe

Observations

Chips and Technologies Inc.
AVI Capture drivers
Preliminary Production Release 1.0.0.0
Installation, Upgrade, Applications tested with etc at the end.

Rev 1.0.0.0
Jan 31, 1998
1. Limited sizes to 320x240. Earlier bigger sizes showed up but were not
supported.
2. Reports dropped frames by using the estimated framerate. Makes the AVI file
more synchronous even if no sound is present.
3. Fixed MSDOS Full Screen and dynamic mode change (3DMaze screen saver)
hang problem when AVI Capture driver is active.
4. Removed misleading display with no resources when installing.

Rev 0.0.0.3
Dec 5, 1997
1. Modified PCVideo.DLL to work with both SMBus and GPIO
2. Modified PCVideo.DLL to return error if VPM is using the Video Port.
3. Modified PCVideo.DLL to do different alignment for 554 and 555.

Rev 0.0.0.2
Nov 11, 1997
Initial release

To Install:
1. Go to the Control Panel from the Start menu (CTRL-ESC, Settings, Control
Panel), select Add New Hardware, Next, No (to windows searching for New
Hardware, since the decoder is on the GPIO pins, Windows will not
detect it), Sound Video and Game Controllers, Have Disk.
SMBus systems (Gateway 2000) do not need special GPIO settings.
The default settings are for GPIO 0 and 1. If your system has different
settings, edit the PCVideo.INI file to reflect the new settings for
GPIO_SDA and GPIO_SCL

To upgrade:
1. First remove the device from the Control Panel, System, Device Manager,
Sound Video and Game Controller, Chips and Technologies Video Capture.
Then install it again like described above.

This release has the following limitations
1. It does not use a VSync Interrupt due to lack of this in the Hardware
2. The frame rate is limited to 5 frames per second (320x240 8bpp, P150)
3. Tearing may be visible, especially if the capture is in 16/24bpp modes.
4. This conflicts with the VPM and only one can be active at a time,
either the VPM or the AVI Capture driver. The AVI Capture driver detects
if the video port is in use and returns an error.
5. Fails a couple of tests of the Microsoft WHQL Video Tests in 320x240.
No errors if reduce size.
6. Overwrites display memory momentarily in some apps when starting.
7. Does not support dynamic mode switching in Windows. Usually see corruption
or loss of overlay.
8. Supports formats upto 320x240 only.
9. Displays and "!" through the device in the Device Manager and reports that
the device is not working properly even though there is no problem.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

VGA

Operating System

Windows 95

Size Driver

99KB

File Name

8xvgaw95.exe

Observations

This file describes normal display driver installation procedures for
Windows 95. Use these procedures when installing the display drivers
provided in this directory.

DRIVER INSTALLATION PROCEDURE

Click Start, then Settings, then Control Panel.

Start the "Display" applet program.

Select the "Settings" page, push the "Change Display Type" button.

Push the "Change" button in the "Adapter Type" area.

Push the "Have Disk" button and press "OK".

Specify the path to the new driver and press the
key:

Example 1: Insert the drivers disk in the A: floppy drive,
and enter A:\.

Example 2: Type in the name of the directory where you copied
the drivers, either on your local hard drive or
on a network share.

Example 3: If you're not sure exactly where the drivers are,
choose the "Browse..." button are find them.

The "Select Device" dialog box will appear. Select the adapter that
corresponds to the one you installed in your machine and click OK.

Windows 95 will copy the display drivers to the proper directories
on your system.

Continue choosing Close until asked to restart your machine from the
"Systems Settings Change" dialog box.

After the system has restarted, you can go back into the Display
applet and select alternate screen resolutions and color depths.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

VGA

Operating System

Windows NT3.5

Size Driver

48KB

File Name

8xvgant35.exe

Observations

DR-HiQV(65550)
HiQVideo Display Driver Package
Release Notes for Windows NT 3.5x

Revision: 1.1.5
Release Date: Apr 23, 1997
================================

The following problems have been fixed in the current release:
1. Generic Mode support added for graphics modes 36,46,47,56 and 57. Panel
Size independent.

Revision: 1.1.3
Release Date: Mar 03, 1997
================================

The following problems have been fixed in the current release:
1. Text output of font with width greater than 16, but less than or equal to 24
pels occasionally caused protection fault to occur.

2. Underline Text Cursor is missing after switching from Desktop to DOS Command
Prompt full screen session.

3. Text expansion getting reset during restore of DOS Command Prompt full screen
session.

4. Invalid refresh selection ( 0 Hz ) listed in Display Settings.

Revision: 1.1.0
Release Date: June 17, 1996
=================================

1. Modified the driver to support the software cursor panning.

2. Fixed a problem with setting and testing the 24bpp modes on
the F65550.
Revision: 1.0.1
Release Date: May 10, 1996
================================

1. Fixed the panning and the cursor offset problems on 800x600
and 1024x768 panels.
Revision: 1.0.0
Release Date: January 31, 1996
====================================

Initial Release.
NOTES: - WINDOWS NT DRIVERS

1) In the 800x600 and 1024x768 resolutions, the screen
image is not displayed correctly on a CRT screen when the
screen is panned to the bottom of the display and the user
switches the display from LCD to CRT.

The Windows 3.1 driver uses the Check_Cursor and
Move_Cursor routines to adjust the screen for panning.
Windows NT does not have a routine analogous to
Check_Cursor.

This limitation exists because Windows NT does not have
a Check_Cursor routine.

This problem is fixed as soon as the user touches the
mouse pointer.

Company

Clevo

Categories

Notebooks & Tablet PCs

Serie

Clevo 8xxx Series

Model

Clevo 8700

Description

VGA

Operating System

Windows NT4

Size Driver

46KB

File Name

8xvgant40.exe

Observations

Windows NT 4.0 -- Chips And Technologies Driver Installation Procedure
--------------------------------------------------------------------------
Step 1: Click the Start button, then go to Settings and click on Control Panel.

Click on the Display icon to start the Display Properties window.

Click on the Settings tab, and then click on Display Type.

In the Change Display Type window, click on Change in Adapter Type.
This will bring up the Select Device Window.

Step 2: Chips & Technologies display drivers can be installed from a
manufacturer supplied Installation Diskette, or from the default
drivers provided on the Windows NT 4.0 CDROM.

Installing from Manufacturer supplied diskette
----------------------------------------------

In the Change Display window, click on Have Disk. Follow the directions
on the screen to supply the directory where the Windows NT driver files
are located. Then select OK, or press enter.

Select Chips Video Accelerator from Display list provided, then click
OK or press enter.

You will then see a warning panel about Third Party Drivers. Click on
Yes to finish the install.

Once the installation is complete, the system must be shut down and
restarted for the new drivers to take effect.
Installing Drivers provided on NT 4.0 CDROM
----------------------------------------------

In the Change Display window, from the list of Manufacturers, select
Chips & Technologies. In the Display Window, select Chips & Technologies
Video Accelerator, then click OK or press enter.

You will then see a warning panel about Third Party Drivers. Click on
Yes to finish the install.

Follow the directions on the screen to supply the directory where the
Windows NT driver files are located. Then select OK, or press enter.

Once the installation is complete, the system must be shut down and
restarted for the new drivers to take effect.
Step 3: When the system has restarted, the default graphics mode ( usually
640x480x256color ) has been automatically selected.

Click the Start button, then go to Settings and click on Control Panel.

Click on the Display icon to start the Display Properties window.

Click on the Settings tab.

A new screen setting can be selected using either of the following
methods:

1: Use the slide-bar in the Desktop Area to select new setting.

2: Click on List All Modes. From the list provided, select a new
setting, then click OK or press enter.

Access to Official Website Clevo

Home English Drivers English

Welcome to the HelpDrivers, driver for printers.

Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more

You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.

Do not rename the file you're downloading, it may cause installation problems.

Available 17 files for Clevo 8700

Select Files