Available 4 files for Emulex LP11002-M4
Select Files
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP11002-M4
Description
EFIBoot
Operating System
Boot Code
Version
3.11x1
Size Driver
122KB
File Name
be311x1_ebc.zip
Observations
Fibre Channel Host Bus Adapters for Fujitsu Primequest Servers Group
Platform: Intel Itanium (64-bit) The current EFI (Extensible Firmware Interface) Boot provides 64-bit system
boot capability through the use of the EFI Shell. EFIBoot supports EFI
Specification 1.10 and EFI Source Code version 1.10.14.61 and 1.10.14.62.
EFIBoot supports:
(1) Multi-Topology : Fabric Point-to-Point; FC-AL: Private Loop and Public
Loop.
(2) EFI Protocols : Configuration, Component Name, Firmware Update, VPD,
LunCtrlAttrs and Diagnostics are supported.
(3) Operating System : Windows Server 2003 and Red-Hat Linux
(4) Multi-Device path : Fibre/SCSI device path selectable through the Driver
Configuration Protocol.
(5) Multi-Initiators : Up to 128 adapters in a system.
(6) Multi-Boot : Eight targets/controller selectable through the Driver
configuration Protocol.
(7) Multi-LUNs : Up to 4096 LUNs/target for a volume set device.
Up to 256 LUNs/target for a peripheral device.
(8) Multi-Mode : Peripheral and Volume Set devices are supported.
(9) Multi-Utility : Setup and firmware update are supported.
Files included in this release:
EFI Byte Code Driver Images:
\rel_notes.txt this file you are reading
\DE311X1.PRG Lp8000 EFIBoot version 3.11X1
\CE311X1.PRG Lp9000 EFIBoot version 3.11X1
\HE311X1.PRG Lp9802 EFIBoot version 3.11X1
\QE311X1.PRG Lp850 EFIBoot version 3.11X1
\RE311X1.PRG Lp952 EFIBoot version 3.11X1
\LE311X1.PRG Lp982 EFIBoot version 3.11X1
\TE311X1.PRG Lp10000 EFIBoot version 3.11X1
\ME311X1.PRG Lp1050 EFIBoot version 3.11X1
\EE311X1.PRG Lp101 EFIBoot version 3.11X1
\BE311X1.PRG Lp11000 EFIBoot version 3.11X1
\JE311X1.PRG Lp1150 EFIBoot version 3.11X1
\ZE311X1.PRG Lpe11000 EFIBoot version 3.11X1
\WE311X1.PRG Lpe1150 EFIBoot version 3.11X1
\YE311X1.PRG Lpe111 EFIBoot version 3.11X1
\ElxCli311X1.efi
***** Important Note ******
(1) EFIBoot was not enabled from loading to system memory:
If the adapter EFIBoot is not enabled from loading to system, this adapter
will not be configured. User must use LP6dutil or some other OS Utility to
enable the EFIBoot in order to make this card bootable.
(2) EFIBoot Bios was enabled to configure the adapter and No Link:
EFIBoot will wait for 15 seconds/adapter to confirm a link.
(3) If two or more adapters have same EFIBoot driver version, EFIBoot will
load only one driver.
(4) If there are adapters with different EFIBoot driver versions, EFIBoot
will load the highest version of the EFIBoot driver.
(5) In order to display Linkup speed, use the latest version of the firmware.
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP11002-M4
Description
Firmware
Operating System
Firmware
Version
2.10a7
Size Driver
332KB
File Name
bf210a7.zip
Observations
Fibre Channel Host Bus Adapters for Fujitsu Primequest Servers Group Compatibility:
This kit supports the LP11002 PCI host adapter.
This kit includes the following files:
README.TXT The file you are reading
BF210A7.ALL All firmware components, no boot code
LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:
-- Changes and corrections between 2.10a7 and 2.10a5:
Changed power management reset handling to prevent some systems
from issuing hardware malfunction errors. (CR 17263, 17382)
Hotswap power-up signature processing was corrected, which allows
proper power-up sequence to complete. (CR 17488)
The address cache buffer entries stored in FLASH which are required
for proper operation during FLASH lockout are now initialized properly.
(CR 16573, 17296, 17367, 17497, 17498)
Removed extraneous debug code which caused a Slim Parity Status Error.
(CR 17495, 17499)
Development, desk checks and source code review found possible problems
that had no reported instances of failure. (CR 17500)
-- Version 2.10a5 was the initial general release of this firmware.
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP11002-M4
Description
Manual
Information
Boot Code
Operating System
Manual
Version
3.11x1
Size Driver
4.9MB
File Name
bootcode.pdf
Observations
Fibre Channel Host Bus Adapters for Fujitsu Primequest Servers Group
Platform: Intel Itanium (64-bit) Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP11002-M4
Description
Manual
Information
Firmware
Operating System
Manual
Version
2.10a7
Size Driver
106KB
File Name
fwupdate.pdf
Access to Official Website Emulex
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.