Available 7 files for Emulex LP1000DC

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

OpenBoot

Operating System

Boot Code

Version

1.50a4

Size Driver

30KB

File Name

to150a4.zip

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 255).
\O150A4.txt The file you are reading

\SO150a4.PRG Lp7000 Open Firmware 1.50a4
\DO150a4.PRG Lp8000 Open Firmware 1.50a4
\CO150a4.PRG Lp9000 Open Firmware 1.50a4
\HO150a4.PRG Lp9802 Open Firmware 1.50a4
\MO150a4.PRG Lp1005 Open Firmware 1.50a4
\TO150a4.PRG Lp10000 Open Firmware 1.50a4
\BO150a4.PRG Lp11000 Open Firmware 1.50a4
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.

(1) This procedure assumes there is already a 'local' boot disk.

(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.

(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding (binding a specific scsi id to a specific wwpn or did).

(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.

----------------------------------------------------------------------

----------------------- NEW CHANGES 1.50a4 ------------------------

1. Added the new link speed selection feature that uses the command
"set-link-speed" to select the desired link speed. The new link
speed now can support up to 4 Gigabaud, and the default link speed
is Auto Select. (CR16047)

2. Added the new Fcode Diag Switch feature that uses the command
"set-fdiag-switch" to turn the diag switch on/off. If the Diag
switch is on, the detail debug error message will be print out
during POST or boot time if there is any link/boot failure.(CR16048)

3. Bug fixed where HBA did not retry under a LOGO response and caused
fabric boot failure. (CR15707)

4. Bug fixed where HBA did not retry the START/STOP command on a SCSI
Queue Full response and caused fabric boot failure. The new number
of retries for Queue Full is up to 10 times and then give up.(CR16049)

5. Changed the new number of retry condition for SCSI Busy to retry
forever. (CR16050)

6. Added the host "port-wwn" and "node-wwn" of the HBA into the reg
property during POST time which was required by system to
allow to collect the Host wwpn/wwnn info during boot.(CR16051)

7. Fixed the bug on fail to report fcp-lun on software BOOT format.
(CR16052)

8. Added the new feature "show-wwpn-child". User can use this command
to show the LUNs target with the desired WWPN only instead of all
WWPNs and LUNs.(CR16053)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

OpenBoot

Operating System

Boot Code

Version

1.50a8

Size Driver

33KB

File Name

to150a8.zip

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 255).
\O150a8.txt The file you are reading

\SO150a8.PRG Lp7000 Open Firmware 1.50a8
\DO150a8.PRG Lp8000 Open Firmware 1.50a8
\CO150a8.PRG Lp9000 Open Firmware 1.50a8
\HO150a8.PRG Lp9802 Open Firmware 1.50a8
\TO150a8.PRG Lp10000 Open Firmware 1.50a8
\BO150a8.PRG Lp11000 Open Firmware 1.50a8
\ZO150a8.PRG Lpe11000 Open Firmware 1.50a8
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.

(1) This procedure assumes there is already a 'local' boot disk.

(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.

(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding ('nailing' a specific scsi id to a specific wwpn or did).

(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.

----------------------------------------------------------------------

----------------------- NEW CHANGES 1.50a8 ------------------------

1. The PCI device ID for Lpe11000 in make file wasn't a correct value,
and cause probe process does not find the Fcode image during POST.
The new release fixed this issue by update the correct PCI device
ID in make file. (CR18053)
----------------------- NEW CHANGES 1.50a7 ------------------------

1. The command of report-luns is not setup as external variable in
FCode, this caused the system fail to compile the report-luns into
the RAM during the boot time, and result a boot failure. The new
fix has setup the report-luns as external variable. (CR17926)
----------------------- NEW CHANGES 1.50a6 ------------------------

1. Added the Report LUN before Test Unit Ready command. (CR17835)

2. Added 60ms delay after PRLI and before the first Report Luns command
is sent out. (CR17836)

3. Changed the FCP Port Completion Timeout to 90 seconds for Start/Stop Unit
command, and others for 30 seconds timeout. (CR17837)

4. Fixed the bug on system hangs during "probe-scsi-all", because the timeout
for FCP completion was greater FCP Response. The new fix will be increased
FCP Response Timeout to 100 seconds for Start/Stop Unit command, and others
for 40 seconds timeout. (CR17838)

5. Fixed the bug for mishandle the return value of TUR when FC cable was not
connect properly during boot time and result an error message of
"STACK UNDERFLOW" issue. (CR17839)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

x86 BootBIOS

Operating System

Boot Code

Version

1.70a3

Size Driver

39KB

File Name

tb170a3.zip

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage
Platform: Intel (32-bit)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

EFIBoot

Operating System

Boot Code

Version

3.11x1

Size Driver

122KB

File Name

te311x1_ebc.zip

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage
Platform: Intel Itanium (64-bit) The current EFI (Extensible Firmware Interface) Boot provides 64-bit system
boot capability through the use of the EFI Shell. EFIBoot supports EFI
Specification 1.10 and EFI Source Code version 1.10.14.61 and 1.10.14.62.

EFIBoot supports:

(1) Multi-Topology : Fabric Point-to-Point; FC-AL: Private Loop and Public
Loop.

(2) EFI Protocols : Configuration, Component Name, Firmware Update, VPD,
LunCtrlAttrs and Diagnostics are supported.

(3) Operating System : Windows Server 2003 and Red-Hat Linux

(4) Multi-Device path : Fibre/SCSI device path selectable through the Driver
Configuration Protocol.

(5) Multi-Initiators : Up to 128 adapters in a system.

(6) Multi-Boot : Eight targets/controller selectable through the Driver
configuration Protocol.

(7) Multi-LUNs : Up to 4096 LUNs/target for a volume set device.
Up to 256 LUNs/target for a peripheral device.

(8) Multi-Mode : Peripheral and Volume Set devices are supported.

(9) Multi-Utility : Setup and firmware update are supported.
Files included in this release:

EFI Byte Code Driver Images:

\rel_notes.txt this file you are reading
\DE311X1.PRG Lp8000 EFIBoot version 3.11X1
\CE311X1.PRG Lp9000 EFIBoot version 3.11X1
\HE311X1.PRG Lp9802 EFIBoot version 3.11X1
\QE311X1.PRG Lp850 EFIBoot version 3.11X1
\RE311X1.PRG Lp952 EFIBoot version 3.11X1
\LE311X1.PRG Lp982 EFIBoot version 3.11X1
\TE311X1.PRG Lp10000 EFIBoot version 3.11X1
\ME311X1.PRG Lp1050 EFIBoot version 3.11X1
\EE311X1.PRG Lp101 EFIBoot version 3.11X1
\BE311X1.PRG Lp11000 EFIBoot version 3.11X1
\JE311X1.PRG Lp1150 EFIBoot version 3.11X1
\ZE311X1.PRG Lpe11000 EFIBoot version 3.11X1
\WE311X1.PRG Lpe1150 EFIBoot version 3.11X1
\YE311X1.PRG Lpe111 EFIBoot version 3.11X1
\ElxCli311X1.efi


***** Important Note ******

(1) EFIBoot was not enabled from loading to system memory:

If the adapter EFIBoot is not enabled from loading to system, this adapter
will not be configured. User must use LP6dutil or some other OS Utility to
enable the EFIBoot in order to make this card bootable.

(2) EFIBoot Bios was enabled to configure the adapter and No Link:

EFIBoot will wait for 15 seconds/adapter to confirm a link.

(3) If two or more adapters have same EFIBoot driver version, EFIBoot will
load only one driver.

(4) If there are adapters with different EFIBoot driver versions, EFIBoot
will load the highest version of the EFIBoot driver.

(5) In order to display Linkup speed, use the latest version of the firmware.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

Firmware

Operating System

Firmware

Version

1.91a5

Size Driver

330KB

File Name

td191a5.zip

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage Compatibility:

This kit supports the LP10000, LP10000DC and LP10000ExDC
PCI host adapters.

This kit includes the following files:

README.TXT The file you are reading

TD191A5.ALL All firmware components, no boot code

LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:

-- Changes and corrections between 1.91a5 and 1.91a4:

Ensure proper DMA behavior upon channel reset. (CR 19091, 19096)

Pre-initialize configuration region to avoid errors if host reads it
before the initial configuration is complete. (CR 19177, 19187, 19188)

-- Changes and corrections between 1.91a4 and 1.91a3:

Several issues with FLASH access during reset of only one port have been
eliminated by synchronizing the flash access speed of both ports.
(CR 17472, 17475, 17539, 17542, 17625, 17626, 17647, 17648, 18212,
18213, 18307)

An exceptionally rigorous test produced a timeout where the rings other
than ring 0 were ignored. The firmware has been corrected to check all
four rings. (CR 15952, 16262, 16279, 16280, 16281, 16282, 16283)

Improved handling of queued data from tape. Recovery of CRC errors
no longer indirectly trigger an abort on slow PCI environments.
(CR 17410, 17510, 17520, 17608, 17610, 17633, 17634, 17635, 18280,
18343)

Changed handling of dropped FCP-2 tape data frames. Upon detecting a
missing frame, the firmware now automatically requests a retransmission
from the drive. (CR 14851, 15184, 16975, 18329)

The firmware now correctly handles intentional IOCB starvation.
(CR 16818, 16873, 16972, 17211)

An I/O timeout during tape operation was eliminated by delaying
processing of any FCP2 errors during discovery. (CR 17363, 18287, 18288)

Improved handling of linked FCP commands in order to avoid timeouts.
(CR 15602, 16114)

Implemented a workaround to avoid a hardware DMA overrun condition.
(CR 17780, 17834, 17908)

To avoid buffer deadlocks, the HBA now completes any existing DMA for
an exchange prior to allocating more free buffers. (CR 16862, 16874,
16973, 18347)

Dump command now correctly dumps memory above 1MB. (CR 18374)

Improved buffer handling logic during error conditions to avoid aborted
exchanges. (CR 17701, 18291, 18292, 18349)

Improved handling of erroneously-sized ECHO responses. (CR 18330,
18332, 18333)

The HBA now transmits all outstanding ACKs before processing any
previously blocked data. (CR 16354, 18334, 18335)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

Manual

Information

Firmware

Operating System

Manual

Version

1.91a5

Size Driver

106KB

File Name

fwupdate.pdf

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for Fujitsu

Model

Emulex LP1000DC

Description

Manual

Information

Boot Code

Operating System

Manual

Version

1.70a3

Size Driver

4.9MB

File Name

bootcode.pdf

Observations

Fibre Channel Host Bus Adapters for Fujitsu Eternus Series Storage
Platform: Intel (32-bit) Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38