Available 2 files for Emulex LP10000DC-M2
Select Files
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP10000DC-M2
Description
OpenBoot
Operating System
Boot Code
Version
1.50a4
Size Driver
30KB
File Name
to150a4.zip
Observations
Fibre Channel Host Bus Adapters for Fujitsu Prime Power E-Server Group
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 255).
\O150A4.txt The file you are reading
\SO150a4.PRG Lp7000 Open Firmware 1.50a4
\DO150a4.PRG Lp8000 Open Firmware 1.50a4
\CO150a4.PRG Lp9000 Open Firmware 1.50a4
\HO150a4.PRG Lp9802 Open Firmware 1.50a4
\MO150a4.PRG Lp1005 Open Firmware 1.50a4
\TO150a4.PRG Lp10000 Open Firmware 1.50a4
\BO150a4.PRG Lp11000 Open Firmware 1.50a4
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.
(1) This procedure assumes there is already a 'local' boot disk.
(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.
(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding (binding a specific scsi id to a specific wwpn or did).
(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.
----------------------------------------------------------------------
----------------------- NEW CHANGES 1.50a4 ------------------------
1. Added the new link speed selection feature that uses the command
"set-link-speed" to select the desired link speed. The new link
speed now can support up to 4 Gigabaud, and the default link speed
is Auto Select. (CR16047)
2. Added the new Fcode Diag Switch feature that uses the command
"set-fdiag-switch" to turn the diag switch on/off. If the Diag
switch is on, the detail debug error message will be print out
during POST or boot time if there is any link/boot failure.(CR16048)
3. Bug fixed where HBA did not retry under a LOGO response and caused
fabric boot failure. (CR15707)
4. Bug fixed where HBA did not retry the START/STOP command on a SCSI
Queue Full response and caused fabric boot failure. The new number
of retries for Queue Full is up to 10 times and then give up.(CR16049)
5. Changed the new number of retry condition for SCSI Busy to retry
forever. (CR16050)
6. Added the host "port-wwn" and "node-wwn" of the HBA into the reg
property during POST time which was required by system to
allow to collect the Host wwpn/wwnn info during boot.(CR16051)
7. Fixed the bug on fail to report fcp-lun on software BOOT format.
(CR16052)
8. Added the new feature "show-wwpn-child". User can use this command
to show the LUNs target with the desired WWPN only instead of all
WWPNs and LUNs.(CR16053)
Company
Emulex
Categories
Networks Cards
Serie
Emulex Products Emulex for Fujitsu
Model
Emulex LP10000DC-M2
Description
Manual
Information
Boot Code
Operating System
Manual
Version
1.50a4
Size Driver
4.9MB
File Name
bootcode.pdf
Observations
Fibre Channel Host Bus Adapters for Fujitsu Prime Power E-Server Group
Platform: SPARC, PowerPC Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Access to Official Website Emulex
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.