Available 6 files for D-Link DS-601
Select Files
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) Manual
Information
Manual
Operating System
Manual
Size Driver
2.2MB
File Name
ds-601_manual.pdf
Observations
File Changes.txt:
D-LINK NetDefend Client ver 1.01 9/11-2004:
changes to all previous versions and builds -
1. Corrected behaviour with some external personal firewalls.
2. When using RSA SIG (Certificates) the client enforced IKE ID type to ASN1
Distinguished Name independent of the configured IKE ID type.
Due to feedback from different partners this has now been changed. The client
now for RSA SIG uses the configured IKE ID type. For current installations using
RSA SIG and where ASN1 DN is used, please check that the IKE ID Type is set to
"ASN1 Distinguished Name". The content of the IKE ID is in this case irrelevant.
3. Support for Netscreen XAUTH and Mode Config (IKECFG).
4. Prompt for XAUTH password if field is left empty.
5. Re-keying of IKE (phase I) without disconnecting fixed.
6. Added support to run concurrently with basically any external firewall.
When an external firewall is installed the NCP firewall should be turned off.
7. Problem with de-installation when using WINXP (SP2) fixed.
Before de-installing the NCP NetDefend Client please update with this build and
then reboot. After reboot you can de-install the NCP NetDefend Client.
8. Hybrid Authentication Mode (eg. CheckPoint XAUTH) now supported.
9. COSINE IKECFG mode corrected.
10.When the RAS dialer and not the NCP internal dialer was used to create the
provider connection, the VPN connection worked properly. After a disconnect
and a second connect the tunnel was established but it was not possible to
communicate over the tunnel. This is now corrected.
11.When using RSA-Signatures (Certificates) the client enforced MAIN mode. This
behaviour has now been changed in such a way that the client always uses the
configured exchange mode.
12.When the client receives unencrypted data in crypto state during the IKE negotiation
it will no longer send a NOTIFY("SITUATION_NOT_SUPPORTED"). This caused some gateways to
terminate the IKE negotiation.
13.When the internal NCP dialer is used and the mediatype is GPRS the PIN and APN
are automatically sent by the client. For the Vodaphone and T-Mobile GPRS/UMTS
cards the wait time after sending the PIN before proceeding was 12 seconds. This
wait time has now been set to 20 seconds to provide a more reliable connect.
14.Corrected split-tunneling behaviour when the clients IP address assignment
is set to "Local Address".
15.The re-keying of phase II affected the re-keying (LifeTime) of phase I.This is now
corrected.
16.Some Firewall's were able to block the client from working properly over lan.
The client was not able to recognize the LAN adapters.This has now been fixed.
17.DEFLATE compression is now supported. The monitor (GUI) still displays
"Use IP compression (LZS)" but both methods are negotiated (LZS and DEFLATE).
Look into the logbook to view what actually was negotiated. The GUI will be corrected.
18.The checkbox "Use IP compression (LZS)" is now corrected to the following:
"Use IP compression"
19.It is now possible to configurate the Domain name within the "IP Address assignment"
tab.
20.Support for more than one user certificate.
21.EAP 802.1x changes:
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) Quick Installation Guide
Information
Quick Installation Guide
Operating System
Manual
Size Driver
645KB
File Name
ds-601_qig.pdf
Observations
File Changes.txt:
D-LINK NetDefend Client ver 1.01 9/11-2004:
changes to all previous versions and builds -
1. Corrected behaviour with some external personal firewalls.
2. When using RSA SIG (Certificates) the client enforced IKE ID type to ASN1
Distinguished Name independent of the configured IKE ID type.
Due to feedback from different partners this has now been changed. The client
now for RSA SIG uses the configured IKE ID type. For current installations using
RSA SIG and where ASN1 DN is used, please check that the IKE ID Type is set to
"ASN1 Distinguished Name". The content of the IKE ID is in this case irrelevant.
3. Support for Netscreen XAUTH and Mode Config (IKECFG).
4. Prompt for XAUTH password if field is left empty.
5. Re-keying of IKE (phase I) without disconnecting fixed.
6. Added support to run concurrently with basically any external firewall.
When an external firewall is installed the NCP firewall should be turned off.
7. Problem with de-installation when using WINXP (SP2) fixed.
Before de-installing the NCP NetDefend Client please update with this build and
then reboot. After reboot you can de-install the NCP NetDefend Client.
8. Hybrid Authentication Mode (eg. CheckPoint XAUTH) now supported.
9. COSINE IKECFG mode corrected.
10.When the RAS dialer and not the NCP internal dialer was used to create the
provider connection, the VPN connection worked properly. After a disconnect
and a second connect the tunnel was established but it was not possible to
communicate over the tunnel. This is now corrected.
11.When using RSA-Signatures (Certificates) the client enforced MAIN mode. This
behaviour has now been changed in such a way that the client always uses the
configured exchange mode.
12.When the client receives unencrypted data in crypto state during the IKE negotiation
it will no longer send a NOTIFY("SITUATION_NOT_SUPPORTED"). This caused some gateways to
terminate the IKE negotiation.
13.When the internal NCP dialer is used and the mediatype is GPRS the PIN and APN
are automatically sent by the client. For the Vodaphone and T-Mobile GPRS/UMTS
cards the wait time after sending the PIN before proceeding was 12 seconds. This
wait time has now been set to 20 seconds to provide a more reliable connect.
14.Corrected split-tunneling behaviour when the clients IP address assignment
is set to "Local Address".
15.The re-keying of phase II affected the re-keying (LifeTime) of phase I.This is now
corrected.
16.Some Firewall's were able to block the client from working properly over lan.
The client was not able to recognize the LAN adapters.This has now been fixed.
17.DEFLATE compression is now supported. The monitor (GUI) still displays
"Use IP compression (LZS)" but both methods are negotiated (LZS and DEFLATE).
Look into the logbook to view what actually was negotiated. The GUI will be corrected.
18.The checkbox "Use IP compression (LZS)" is now corrected to the following:
"Use IP compression"
19.It is now possible to configurate the Domain name within the "IP Address assignment"
tab.
20.Support for more than one user certificate.
21.EAP 802.1x changes:
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) Configure NetDefend with XAUTH
Information
Manual
Operating System
Manual
Size Driver
272KB
File Name
dfl-ds_601_xauth.pdf
Observations
DFL-200,700,1100 – DS-601 XAUTH
Log on to the DFL firewall and go to Firewall and then click on Users
At the bottom on the Users screen click on Add New
Write in the username you want in the box for User name:
Then add a password and retype the selected password click on Apply and activate all the changes made in the Firewall and restart the unit.
Start your DS-601 client software and go to Configuration and choose Profile Settings.
Click your selected Profile and press Configure.
Go to Identities and mark the box for Use extended authentication ( XAUTH), write in the Username and password you selected in the DFL firewall and then press OK to confirm.
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) Datasheet
Information
Manual
Operating System
Manual
Size Driver
310KB
File Name
ds-601_605.pdf
Observations
Network Security VPN Client
Providing your employees working away from the office with a secure remote access to mission-critical resources on your
corporate network is crucial to your company's success. While they want a solution that's reliable and easy to use, you need
one that is secure, flexible and simple to manage. D-Link provides you with a solution that meets your company and employees'
needs.
IPSec Client
Easy-to-Use Security Solution
The D-Link VPN Client Software is a versatile, secure and
economical IPSec client. It is designed for Virtual Private
Network (VPN) products and terminates against IPSec
gateways, such as the D-Link VPN routers and NetDefend
firewalls. The connection can be established over a wired or
wireless network, the public Internet or a private network.
This software supports all IPSec standards set in the RFCs.
The product meets the highest security requirements.
An integrated personal firewall shields against attacks
from the Internet. The latest encryption algorithms protect
sensitive data in transit.
With the D-Link VPN Client, your mobile users have a
simple, easy-to-use solution for securely accessing the
corporate network. The VPN Client software provides
mobile users with secure, reliable access to corporate
resources through broadband, wireless and dial-up
connections.
The D-Link VPN Client uses innovative technology to deliver
tighter integration for greater ease of use and manageability.
VPN Client provides cost-effective, secure access for mobile
users from any location, using any Internet connection, over
any IP network environment.
The D-Link VPN Client uses standard IPSec implementation
with advanced 3DES/AES encryption and comprehensive
Windows support. This software provides NAT transparency
capability to work with most home gateways and NAT routers.
RADIUS authentication is supported for centralized user
database management.
D-Link VPN Client software provides connection from remote
mobile users with all D-Link VPN routers and firewalls,
including the DI-804HV, DI-808HV, DI-824VUP+, DFL-80,
DFL-100, DFL-200, DFL-300, DFL-500, DFL-600, DFL-700,
DFL-900*, DFL-1100 and DFL-1500.
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) DFL-800/1600/2500 IPsec connection with DS-601/605 guide
Information
Manual
Operating System
Manual
Size Driver
461KB
File Name
dfl-800_1600_2500-vpn_ipsec_server_for_netdefend.pdf
Observations
1. Create the pre-shared key first.
2. IPSec tunnel setting (general page): this is for remote clients to dial in
3. select the pre-shared key you created.
4. Enable the option shown below.
5. Choose the IKE and PFS at your will.
6. Disable this option shown below. This isn’t necessary for remote dial in clients.
7. Combine the ipsec and lan interface
8. create the necessary rule.
Company
D-Link
Categories
Networks Cards
Model
D-Link DS-601
Description
VPN Remote Access Software (1 User License) 30 day trial software
Operating System
Software
Version
1.03
Size Driver
7.6MB
File Name
ds-601_remote_access_vpn_software_30day.zip
Observations
File Changes.txt:
D-LINK NetDefend Client ver 1.01 9/11-2004:
changes to all previous versions and builds -
1. Corrected behaviour with some external personal firewalls.
2. When using RSA SIG (Certificates) the client enforced IKE ID type to ASN1
Distinguished Name independent of the configured IKE ID type.
Due to feedback from different partners this has now been changed. The client
now for RSA SIG uses the configured IKE ID type. For current installations using
RSA SIG and where ASN1 DN is used, please check that the IKE ID Type is set to
"ASN1 Distinguished Name". The content of the IKE ID is in this case irrelevant.
3. Support for Netscreen XAUTH and Mode Config (IKECFG).
4. Prompt for XAUTH password if field is left empty.
5. Re-keying of IKE (phase I) without disconnecting fixed.
6. Added support to run concurrently with basically any external firewall.
When an external firewall is installed the NCP firewall should be turned off.
7. Problem with de-installation when using WINXP (SP2) fixed.
Before de-installing the NCP NetDefend Client please update with this build and
then reboot. After reboot you can de-install the NCP NetDefend Client.
8. Hybrid Authentication Mode (eg. CheckPoint XAUTH) now supported.
9. COSINE IKECFG mode corrected.
10.When the RAS dialer and not the NCP internal dialer was used to create the
provider connection, the VPN connection worked properly. After a disconnect
and a second connect the tunnel was established but it was not possible to
communicate over the tunnel. This is now corrected.
11.When using RSA-Signatures (Certificates) the client enforced MAIN mode. This
behaviour has now been changed in such a way that the client always uses the
configured exchange mode.
12.When the client receives unencrypted data in crypto state during the IKE negotiation
it will no longer send a NOTIFY("SITUATION_NOT_SUPPORTED"). This caused some gateways to
terminate the IKE negotiation.
13.When the internal NCP dialer is used and the mediatype is GPRS the PIN and APN
are automatically sent by the client. For the Vodaphone and T-Mobile GPRS/UMTS
cards the wait time after sending the PIN before proceeding was 12 seconds. This
wait time has now been set to 20 seconds to provide a more reliable connect.
14.Corrected split-tunneling behaviour when the clients IP address assignment
is set to "Local Address".
15.The re-keying of phase II affected the re-keying (LifeTime) of phase I.This is now
corrected.
16.Some Firewall's were able to block the client from working properly over lan.
The client was not able to recognize the LAN adapters.This has now been fixed.
17.DEFLATE compression is now supported. The monitor (GUI) still displays
"Use IP compression (LZS)" but both methods are negotiated (LZS and DEFLATE).
Look into the logbook to view what actually was negotiated. The GUI will be corrected.
18.The checkbox "Use IP compression (LZS)" is now corrected to the following:
"Use IP compression"
19.It is now possible to configurate the Domain name within the "IP Address assignment"
tab.
20.Support for more than one user certificate.
21.EAP 802.1x changes:
Access to Official Website D-Link
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.