Available 14 files for Bluestork BS-GIGA
Select Files
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
FreeBSD
Size Driver
23KB
File Name
freebsd.zip
Observations
Realtek 8139C/8139C+/8169S/8169SB/8169SC/8168B/8101E Driver for FreeBSD v4.x/5.1
This driver is modified by Realtek Semiconductor corp. and it has been tested OK
on FreeBSD v5.1, FreeBSD v5.4, and FreeBSD v6.0. To update the driver, you may use method 1. If method 1 failed,
you must use method 2 which is more complex.
Method 1:
1.Copy if_rl.ko in "modules" directory to "/modules" directory and overwrite
the existing file.
2.Modify the file "/boot/defaults/loader.conf" and set "if_rl_load" in "Network
drivers" section to "Yes"
3.Reboot.
Method 2:
Because the FreeBSD kernel has default drivers to support RTL8139C and RTL8169S. To use the RTL8139C+, RTL8169SB, RTL8169SC, RTL8168B, and RTL8101E, you need to update your NIC driver by recompiling your FreeBSD kernel.
The main steps you have to do:(FreeBSDSrcDir means the directory of FreeBSD source code
and it may be "/usr/src/sys")
0. Replace your NIC with the card listed above.
1. recompile your kernel (you must install your FreeBSD source code first !!)
# vim /usr/src/sys/i386/conf/GENERIC and delete rl and re
# vim /usr/src/sys/module/Makefile and delete rl and re
# cd /usr/src/sys/i386/conf
# /usr/sbin/config GENERIC
# cd ../compile/GENERIC
# make depend
# make
# make install
# reboot
2. copy if_rl.c and if_rlreg.h to /usr/src/sys/pci directory
(suggestion: keep the orginal if_rl.c and if_rlreg.h)
3. #cd /usr/src/sys/modules/rl
4. # make clean; make
5. # kldload ./if_rl.ko
6. for static ip
# ifconfig rl0
for dhcp
# /sbin/dhclient rl0
Question & Answer:
Q:How to compile under FreeBSD v4.x ?
A:Change the definition of "OS_VER" in if_rlreg.h
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Linux
Size Driver
18KB
File Name
linux.zip
Observations
This is the Linux device driver released for RealTek Ethernet controllers, which are listed as following.
1. RTL8169S/SB/SC (Gigabit Ethernet with PCI interface)
2. RTL8168B (Gigabit Ethernet with PCI-Express interface)
3. RTL8101E (Fast Ethernet with PCI-Express interface)
- kernel source tree (supported versions 2.4.x or 2.6.x)
- compiler/binutils for kernel compilation
Unpack the tarball :
unzip r1000_linuxdrv_vxx.zip
Change to the directory:
cd r1000
If you are running the target kernel, then you should be
able to do :
make clean modules (as root or with sudo)
make install
depmod -a
The media can be forced to one of the 5 modes as follows.
Cmd: "insmod r1000 media = SET_MEDIA"
For example:
"insmod r1000 media = 0x04" will force PHY to operate in 100Mpbs Half-duplex.
SET_MEDIA can be:
_10_Half = 0x01
_10_Full = 0x02
_100_Half = 0x04
_100_Full = 0x08
_1000_Full = 0x10
Force media type for multiple cards could be performed as:
"insmod r1000 media=0x04,0x10"
which force PHY to operate at 100Mbps half-duplex and 1000Mbps full-duplex.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
MAC10
Size Driver
411KB
File Name
mac10.zip
Observations
This is the Mac OS X driver for Realtek RTL8169/RTL8110 Family PCI Gigabit Ethernet NIC. The system will be rebooted after the driver is installed, so please close all the other applications before installing the driver. After the system is rebooted, please follow the following steps to configure the network:
1. Select the "System Preference" from the system menu.
2. Select and launch the "Network" item in the "System Preference" folder.
3. From the "Configure" list, select the adapter to be configured.
4. Configure the settings.
5. Click the "Save" button.
Then you can connect to the Ethernet.......
NOTE: This driver is for Mac OS X 10.2 or newer versions. THIS DRIVER IS NOT FOR MAC OS X 10.1.x. If your Mac OS X is 10.1.x, please update your Mac OS X to 10.2
MAC 10.4
1.11
- - first release version of rtl8169 mac 10.4 driver
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
MAC9X
Size Driver
26KB
File Name
mac9x.zip
Observations
The RTL8169 driver does not support the HOT-SWAP functionality of a PC Card.
Thus you must plug the PC Card into your system before booting and should not
remove the PC Card from your system before shuting down. PLEASE DO NOT
HOT-SWAP THE PC CARD WHEN YOUR MAC SYSTEM IS RUNNING.
1. Adapter requirement for PCI adapter
2. Adapter requirement for PC Card
3. Software Installation
4. Setting up Open Transport
5. Setting up the TCP/IP
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Netware
Size Driver
71KB
File Name
netware.zip
Observations
Server Driver for NetWare 5.X
Introduction:
-------------
This document describes the procedure to install the NetWare v5.X
server driver for REALTEK RTL8169 Gigabit Ethernet adapter.
Location of Driver: \NETWARE\SERVER\RTGBSRV.LAN
Installaton Procedure :
---------------------
Before you start with the installation process, make sure that
the Novell NetWare v5.X server is properly installed.
Similarly, your adapter should also be properly installed in your
server.
1. Insert the Realtek Driver Diskette into drive A and check the
contents of subdirectory \NETWARE\SERVER, It should contain the
following file :
RTGBSRV.LANÄ Novell NetWare V5.X Server Driver
RTGBSRV.LDIÄ Novell NetWare V5.X Server Driver Installation
Information File
2. At the NetWare prompt (indicated by the Server name), run the
NWCONFIG.NLM program by typing:
server name: LOAD NWCONFIG
3. Select " Driver options " and press
4. Select " Configure network drivers " and press
5. Select " Select an addtional driers " and press
6. Press the key to specify other drivers to install.
7. Press
and press
8. The RTGBSRV.LAN driver should appear in your choice list for the
'Select a Driver to install' field. Choose this driver and press
9. Press
SYSTEM directory. And then it will start driver loading and
binding procedure. This will allow you to load and bind all 4
frame types supported by NetWare.
10. Add the LOAD and BIND statements you require to the server's
AUTOEXEC.NCF file so that the LAN driver will load automatically
each time the server starts up.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Nwclient
Size Driver
71KB
File Name
nwclient.zip
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Unixware 7
Size Driver
32KB
File Name
unixware_7.zip
Observations
SCO UnixWare 7.x
Introduction:
-------------
This document describes the procedure to install the SCO UnixWare 7
driver for Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter.
Location of Driver: \uw7\rtgb.tar
Installing driver procedure on SCO UnixWare7 :
-----------------------------------------
Before you start with the installation process, make sure that the
SCO UNIX system is properly installed. Similarly, your adapter should
also be properly installed in your machine.
1. Installation Diskette in DOS format.
Put RTL SCO UnixWare Driver diskette to floppy A: and use doscp
command to copy RTL SCO UnixWare Driver into UNIX's directories.
NOTE: In UnixWare 7.1.1, you must install the "mtools" package included
within the OS and use "mcopy" instead of "doscp".
# cd /
# doscp A:uw7/rtgb.tar /tmp
2. Run 'tar' utility to extract the driver.
# cd /tmp
# tar -xvf rtgb.tar
3. Run 'pkgadd' utility to add the driver software to system.
# pkgadd -d /tmp/pkg
=> Type Enter to add the driver package to the system.
=> Type q to quit
4. Use 'scoadmin' utility to add adapters.
# scoadmin
=> Select "Networking" item from the item list and press enter.
=> Select "Network Configuration Manager" item from the item list
and press enter.
=> Select "Add New Lan Adapter" menu item from "Hardware".
=> Select the Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter item from the item list.
=> Add protocol(s) to the adapter.
5. Return to the command prompt.
6. Shutdown the system and reboot.
NOTE: 1. If you want to install more than one network adapter, you
should do the 4th, 5th, 6th steps above for each network card
separately.
2. This driver can support up to four network adapters.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows 2000
Size Driver
78KB
File Name
win2000.zip
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows 2003
Size Driver
174KB
File Name
win2003.zip
Observations
Introduction:
-------------
This document describes the procedure to install Windows 2003
driver for Realtek RTL8169 PCI Gigabit Ethernet adapter.
Location of Driver : \Win2003\Rtnicxp.sys
\Win2003\Rtnic64.sys (for Windows 2003 64 bit)
Installing driver procedure on Microsoft Win2003 :
-------------------------------------------------------------------
Before you start with the installation process, make sure that your
adapter should be properly installed in your PCI bus slot.
Executing Win2003, it will auto-detect your system configuration
and find the adapter hardware.
1. When Windows 2003 prompts with "PCI Ethernet Controller" in
"New Hardware Found" dialog box, click the "Next" button.
2. Select "Search for the best driver for your device (Recommended)"
form the "Add New Hardware Wizard" dialog box, then click the
"Next" button.
3. Insert the Realtek RTL8169 driver disk into drive A and specify
the setup file pathname A:\Win2003, then click the "Next" button.
4. Windows 2003 will prompt with "Realtek RTL8169/8110 Family
Gigabit Ethernet NIC" in the "Add New Hardware Wizard" dialog
box.
5. Click the "Next" button in the "Add New Hardware Wizard" dialog
box,then Windows 2003 will copy the driver(.sys) from A:\Win2003
to the C:\WINDOWS\SYSTEM directory and the driver(.inf) from
A:\Win2003 to the C:\WINDOWS\INF directory.
6. When Windows prompts with "Realtek RTL8169/8110 Family
Gigabit Ethernet NIC" in the "Add New Hardware Wizard"
dialog box, click the "Finish" button.
7. Win2003 will finish the other installation procedure
automatically, then you restart the system.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows 98
Size Driver
42KB
File Name
win98.zip
Observations
Introduction:
-------------
This document describes the procedure to install Windows 98
driver for Realtek RTL8169 PCI Gigabit Ethernet adapter.
Location of Driver : \Win98\RTLNIC4.SYS
Installing driver procedure on Microsoft Win98 :
-------------------------------------------------------------------
Before you start with the installation process, make sure that your
adapter should be properly installed in your PCI bus slot.
Executing Win98, it will auto-detect your system configuration
and find the adapter hardware.
1. When Windows 98 prompts with "PCI Ethernet Controller" in
"New Hardware Found" dialog box, click the "Next" button.
2. Select "Search for the best driver for your device (Recommended)"
form the "Add New Hardware Wizard" dialog box, then click the
"Next" button.
3. Insert the Realtek RTL8169 driver disk into drive A and specify
the setup file pathname A:\Win98, then click the "Next" button.
4. Windows 98 will prompt with "Realtek RTL8169/8110 Family
Gigabit Ethernet NIC" in the "Add New Hardware Wizard" dialog
box.
5. Click the "Next" button in the "Add New Hardware Wizard" dialog
box,then Windows 98 will copy the driver(.sys) from A:\Win98
to the C:\WINDOWS\SYSTEM directory and the driver(.inf) from
A:\Win98 to the C:\WINDOWS\INF directory.
6. When Windows prompts with "Realtek RTL8169/8110 Family
Gigabit Ethernet NIC" in the "Add New Hardware Wizard" dialog
box, click the "Finish" button.
7. Win98 will finish the other installation procedure
automatically, then you restart the system.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows 98Se
Size Driver
178KB
File Name
win98se.zip
Observations
Name: RTSNT.602
Version: Ver. 5.602.619.2003
Released By: Andy Liao
Release Date: 06/20/2003
Command:
1. RTL8139/810x/c+/8169/8110 all_in_one NDIS4/5/51 drivers first released.
2. For RTL8169s/8110s mass production
3. For RTL8139c+:
During system shutdown, just stop the hardware and ignore the
transmit/receive buffer queue in the memory.
################################################################################
Name: RTSNT.604
Version: Ver. 5.604.718.2003
Released By: Andy Liao
Release Date: 07/22/2003
Command:
1. Fixed nVidia on board VGA share interrupt S3 fail issue
2. Fixed copy huge file fail on nVidia chipset (compatibility issue)
3. Fixed continuous plug/unplug with Marvell Phy PING fial issue
################################################################################
Name: RTSNT.605
Version: Ver. 5.605.804.2003
Released By: Andy Liao
Release Date: 08/06/2003
Command:
For RTL8169/8110:
1. NWay Foolproof Capability, that is to say,
if user force 100Full and 100H/10F/10H could work normally
2. Raise the performance of WinNT4.0 NDSI4 driver
3. Tune the performance of Win2000/XP and make it stable
################################################################################
Name: RTSNT.606
Version: Ver. 5.606.811.2003
Released By: Andy Liao
Release Date: 08/13/2003
Command:
For RTL8139C+:
1. Fixed the Win98 can't connect with WinNT4 by NetBEUI protocol issue
2. To pass the new Microsoft NDIS test version 4.03.0030 (packet filter)
For RTL8169/8110:
1. Fixed the Win98 can't connect with WinNT4 by NetBEUI protocol issue
2. Fixed the miniportReset routine to make it compatible with our
Windows diagnostic program
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows Me
Size Driver
45KB
File Name
winme.zip
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows NT4
Size Driver
50KB
File Name
winnt4.zip
Observations
Introduction:
-------------
This document describes the procedure to install Windows NT v4.0
driver for Realtek RTL8169 PCI Gigabit Ethernet adapter.
Location of Driver: \WINNT4\RTLNIC4.SYS
Installing driver procedure on Microsoft Windows NT :
-----------------------------------------------------
1. In the "My Computer" icon of Winnt4, choose the "Control Panel"
icon.
2. In the "Control Panel" window, choose the "Network" icon.
3. In the Network Settings dialog box, choose the "Adapters"
item. The Add Network Adapter dialog box appears.
4. In the list of network cards, select "Have Disk...", and
then press
5. Insert this driver disk in drive A, enter drive and pathname
A:\Winnt4 and then choose the
6. In the installed adapter dialog box, you will see the product
list as following:
"Realtek RTL8169/8110 Family Gigabit Ethernet NIC"
in the menu, select the exact product and use
to install it.
7. After that, installation is completed.
8. To complete network installation, remember binding the adapter
to transport drivers by choosing
Setting dialog box.
9. Restarting your system you will acquire network service.
Company
Bluestork
Categories
Networks Cards
Model
Bluestork BS-GIGA
Description
Drivers
Operating System
Windows XP
Size Driver
174KB
File Name
winxp.zip
Access to Official Website Bluestork
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.