Available 5 files for Accton EN1207D
Select Files
Company
Accton
Categories
Networks Cards
Model
Accton EN1207D
Description
Fast Ethernet Adapter
Operating System
DOS-Windows 95-98-Me-NT-2000-XP-OS/2-Linux
Size Driver
501KB
File Name
en1207d.zip
Observations
How to Config Your PCI adapter
==============================
1. Go to the PCI configuration item in BIOS setup.
2. Follow these steps to configure the PCI slot:
a). You should know which slot your adapter is plugged in to.
Look for the physical location of the slot in your PCI
motherboard.
b). Set the "this device" field to "Enable".
c). Set the "this item" field to "Master".
The EN1207D/EN2242A series PCI adapter MUST be installed in an
expansion slot that supports "Bus Master".
Refer to your system documentation to determine which slots
support Bus Mastering.
d). Some BIOS Setups allow you to select which interrupt line you
can use. In this case, select "INT A" for the "this item" field.
e). Select an IRQ of your choice; make sure it does not conflict
with existing IRQs in use.
d). Select the "Trigger method" by which the IRQ is assigned or
routed to the PCI slot. Choose the "level-trigger" option.
Multiple EN1207D/EN2242A series PCI adapters can share the same PCI
interrupt, but all must use INTA with level-trigger mode.
3. Run the diagnostic program found in the driver diskette under DOS.
If any problem arises during the installation, contact your dealer or
Accton Technology Corporation for support.
Conflict with Microsoft EMM386
==============================
The PCI adapters can only function with the EMM386.EXE memory manager
program version 4.49 or later. You can verify its version number by
entering EMM386 at the DOS Prompt.
Do not specify the "highscan" option with the EMM386.exe statement
in your config.sys file or your system will hang.
If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert
the HIGHSCAN flag into the EMM386 command line. This parameter cannot
be manually removed once it's installed, doing so will cause the
extended memory manager to malfunction.
Company
Accton
Categories
Networks Cards
Model
Accton EN1207D
Description
Drivers
Operating System
Windows 2000-XP
Size Driver
46KB
File Name
accton_en1207_95b.zip
Observations
(A) Installing NDIS4 Miniport driver in Microsoft Windows 95 OSR2
=================================================================
1. Plug Accton's EN1207D series adapter into one of the Master PCI
slots of your PCI platform.
2. Turn the power ON then boot into Windows 95.
3. Windows 95 will prompt with "PCI Ethernet Controller" in
the "New Hardware Found" dialog box and "Update Device Driver
Wizard" dialog box.
4. Insert the Accton EN1207D Series Driver Diskette in your floppy drive.
5. Click the "Next >" button in "Update Device Driver Wizard"
dialog box.
6. Windows 95 will prompt with "Accton EN1207D Series PCI Fast Ethernet
Adapter" in the "Update Device Driver Wizard" dialog box.
7. Click the "Finish" button in the "Update Device Driver Wizard"
dialog box.
8. Enter the full pathname A:\WIN95SR2 of the ACC07D.INF file, then
click the OK button in the "Copying Files..." dialog box.
9. Follow the screen's prompt to insert the "Windows 95 CD-ROM"
and click the OK button in the "Insert Disk" dialog box.
10. Otherwise enter the full pathname of the "Windows 95 CD-ROM"
installation files in "Copying Files..." dialog box,
and then click the OK button.
11. Windows 95 will copy the driver (ACC07D.SYS) from A:\WIN95
to C:\WINDOWS\SYSTEM directory and the ACC07D.INF file from
A:\WIN95 to C:\WINDOWS\INF directory.
12. Remove the Accton EN1207D Series Driver Diskette from your floppy drive.
13. Restart your computer to initialize the network function.
NOTICE!! C:\WINDOWS is the directory where your Windows 95 OSR2
O.S. is located.
(B) Configuring NDIS4 Miniport driver in Microsoft Windows 95 OSR2
====================================================================
1. Click the "My Computer" icon in the Main Program Group.
2. Click the "Control Panel" icon in the My Computer window.
3. Click the "Network" icon in the Control Panel window.
4. Select the "Accton EN1207D Series PCI Fast Ethernet Adapter" item
from the "Network" dialog box, and then click the "Properties"
button.
5. Click the "Advanced" button in the "Accton EN1207D Series PCI Fast
Ethernet Adapter Properties" dialog box.
6. Select the Line Speed value (Auto,100full,100half,10full,10half
from the "Value" item, and then click the OK button in the
"Accton EN1207D Series PCI Fast Ethernet Adapter Properties" dialog box.
7. Click the OK button in the "Network" dialog box.
8. Restart your computer to initialize the new configuration.
Company
Accton
Categories
Networks Cards
Model
Accton EN1207D
Description
Drivers
Operating System
Windows 95A
Version
1.08.99.0119
Size Driver
15KB
File Name
accton_en1207_w95.zip
Observations
(A) Installing NDIS3 Miniport driver in Microsoft Windows 95 (OSR1)
===================================================================
1. Plug Accton's EN1207D series adapter into one of the Master PCI
slots of your PCI platform.
2. Turn the power ON and then boot into Windows 95.
3. Windows 95 will prompt with "PCI Ethernet Controller" in
the "New Hardware Found" dialog box.
4. Select "Driver from disk provided by hardware manufacturer"
from the "New Hardware Found" dialog box, then click the OK button.
5. Insert the Accton EN1207D Series Driver Diskette in your floppy
drive.
6. Enter the driver pathname, i.e. A:\WIN95, then click the OK
button in the "Install from Disk" dialog box.
7. Follow the screen's prompt to insert the "Windows 95 CD-ROM"
and click the OK button in the "Insert Disk" dialog box.
8. Otherwise enter the full pathname of the "Windows 95 CD-ROM"
installation files in the "Copying Files..." dialog box,
then click the OK button.
9. Windows 95 will copy the driver (ACC07D.SYS) from A:\WIN95
to C:\WINDOWS\SYSTEM directory and the ACC07D.INF file
from A:\WIN95 to C:\WINDOWS\INF directory.
10. Remove the Accton EN1207D Series Driver Diskette from your floppy
drive.
11. Restart your computer to initialize the network function.
NOTICE!! C:\WINDOWS is the directory where your Windows 95
O.S. is located.
(B) Configuring NDIS3 Miniport driver in Microsoft Windows 95 (OSR1)
====================================================================
1. Click the "My Computer" icon in the Main Program Group.
2. Click the "Control Panel" icon in the My Computer window.
3. Click the "Network" icon in the Control Panel window.
4. Select the "Accton EN1207D Series PCI Fast Ethernet Adapter" item
from the "Network" dialog box, and then click the "Properties"
button.
5. Click the "Advanced" button in the "Accton EN1207D Series PCI Fast
Ethernet Adapter Properties" dialog box.
6. Select the Line Speed value (Auto,100full,100half,10full,10half
from the "Value" item, and then click the OK button in the
"Accton EN1207D Series PCI Fast Ethernet Adapter Properties" dialog box.
7. Click the OK button in the "Network" dialog box.
8. Restart your computer to initialize the new configuration.
Company
Accton
Categories
Networks Cards
Model
Accton EN1207D
Description
Drivers
Operating System
Windows 95B
Version
1.10.0820
Size Driver
46KB
File Name
accton_en1207_95b.zip
Observations
(A) Installing NDIS4 Miniport driver in Microsoft Windows 95 OSR2
=================================================================
1. Plug Accton's EN1207D series adapter into one of the Master PCI
slots of your PCI platform.
2. Turn the power ON then boot into Windows 95.
3. Windows 95 will prompt with "PCI Ethernet Controller" in
the "New Hardware Found" dialog box and "Update Device Driver
Wizard" dialog box.
4. Insert the Accton EN1207D Series Driver Diskette in your floppy drive.
5. Click the "Next >" button in "Update Device Driver Wizard"
dialog box.
6. Windows 95 will prompt with "Accton EN1207D Series PCI Fast Ethernet
Adapter" in the "Update Device Driver Wizard" dialog box.
7. Click the "Finish" button in the "Update Device Driver Wizard"
dialog box.
8. Enter the full pathname A:\WIN95SR2 of the ACC07D.INF file, then
click the OK button in the "Copying Files..." dialog box.
9. Follow the screen's prompt to insert the "Windows 95 CD-ROM"
and click the OK button in the "Insert Disk" dialog box.
10. Otherwise enter the full pathname of the "Windows 95 CD-ROM"
installation files in "Copying Files..." dialog box,
and then click the OK button.
11. Windows 95 will copy the driver (ACC07D.SYS) from A:\WIN95
to C:\WINDOWS\SYSTEM directory and the ACC07D.INF file from
A:\WIN95 to C:\WINDOWS\INF directory.
12. Remove the Accton EN1207D Series Driver Diskette from your floppy drive.
13. Restart your computer to initialize the network function.
NOTICE!! C:\WINDOWS is the directory where your Windows 95 OSR2
O.S. is located.
(B) Configuring NDIS4 Miniport driver in Microsoft Windows 95 OSR2
====================================================================
1. Click the "My Computer" icon in the Main Program Group.
2. Click the "Control Panel" icon in the My Computer window.
3. Click the "Network" icon in the Control Panel window.
4. Select the "Accton EN1207D Series PCI Fast Ethernet Adapter" item
from the "Network" dialog box, and then click the "Properties"
button.
5. Click the "Advanced" button in the "Accton EN1207D Series PCI Fast
Ethernet Adapter Properties" dialog box.
6. Select the Line Speed value (Auto,100full,100half,10full,10half
from the "Value" item, and then click the OK button in the
"Accton EN1207D Series PCI Fast Ethernet Adapter Properties" dialog box.
7. Click the OK button in the "Network" dialog box.
8. Restart your computer to initialize the new configuration.
Company
Accton
Categories
Networks Cards
Model
Accton EN1207D
Description
Drivers
Operating System
Windows 98-98Se-Me
Size Driver
19KB
File Name
accton_en1207.zip
Observations
(A) Installing the NDIS5 Miniport driver on Microsoft Windows 98
=================================================================
1. Plug Accton's EN1207D series adapter into one of the Master PCI
slots of your PCI platform.
2. Turn pthe ower ON, then boot from Windows 98.
3. When Windows 98 prompts with "PCI Ethernet Controller" in
"New Hardware Found" dialog box, click the "Next" button.
4. Select "Search for the best driver for your device (Recommended)"
form the "Add New Hardware Wizard" dialog box, then click the
"Next" button.
5. Insert the Accton EN1207D Series Driver Diskette in your floppy drive.
6. Select "Specify a location" and type Path "A:\WIN98" in the
"Add New Hardware Wizard" dialog box, then click the "Next" button.
7. Click the "Next" button in the "Add New Hardware Wizard" dialog box.
8. Windows 98 will prompt with "Accton EN1207D Series PCI Fast Ethernet
Adapter" in the "Add New Hardware Wizard" dialog box.
9. Click the "Next" button in the "Add New Hardware Wizard" dialog box, then
Windows 98 will copy the driver (ACC07D.SYS) from A:\WIN98
to the C:\WINDOWS\SYSTEM directory and the NETACC07.INF file from A:\WIN98
to the C:\WINDOWS\INF directory.
10. When Windows prompts with "Accton EN1207D Series PCI Fast Ethernet
Adapter" in the "Add New Hardware Wizard" dialog box, click the "Finsh"
button.
11. Remove the Accton EN1207D Series Driver Diskette from your floppy drive.
12. Restart your computer to initialize the network function.
NOTICE!! C:\WINDOWS is the directory where your Windows 98
O.S. is located.
(B) Configuring the NDIS5 Miniport driver on Microsoft Windows 98
====================================================================
1. Click the "My Computer" icon in the Main Program Group.
2. Click the "Control Panel" icon in the My Computer window.
3. Click the "Network" icon in the Control Panel window.
4. Select the "Accton EN1207D Series PCI Fast Ethernet Adapter" item
from the "Network" dialog box, then click the "Properties" button.
5. Click the "Advanced" button in the "Accton EN1207D Series PCI Fast
Ethernet Adapter Properties" dialog box.
6. Select the Line Speed value (Auto,100full,100half,10full,10half)
for the "Value" item, then click the OK button in the "Accton
EN1207D Series PCI Fast Ethernet Adapter Properties" dialog box.
7. Click the OK button in the "Network" dialog box.
8. Restart your computer to implement the new configuration.
Access to Official Website Accton
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.