Available 3 files for Keydata Keynote 8320 - Green 732
Select Files
Company
Keydata
Categories
Fax & Modem & ISDN
Model
Keydata Keynote 8320 - Green 732
Description
User Manual 15 Inch LCD
Information
User Manual
Operating System
Manual
Size Driver
3.2MB
File Name
8320-15.pdf
Observations
The best kind of AC power source to connect your Notebook to is a UPS (Uninterruptible Power Supply). Lacking this, use a power strip with a built-in surge protector. Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery.
Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry.
Turning On Your Notebook Computer
Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The Power-On Self Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows ME, Windows 2000…. etc) is installed, it should start automatically.
To turn the Notebook off, save your work and close all open applications, click on Start, then Shut Down and select Shut down the computer and click "Yes" or press the power button for 4-6 seconds.
Operating on Battery Power
Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions:
Company
Keydata
Categories
Fax & Modem & ISDN
Model
Keydata Keynote 8320 - Green 732
Description
User Manual 16 Inch LCD
Information
User Manual
Operating System
Manual
Size Driver
3.2MB
File Name
8320-16.pdf
Observations
Please read these safety instructions carefully.
Please keep this User's Manual for later reference.
Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible.
Please keep this equipment from humidity.
Lay this equipment on a reliable surface when installed. A drop or fall could cause injury.
Make sure to use the right voltage for the power source when connecting the
equipment to the power outlet.
Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage.
Never pour any liquid into the opening, this could cause fire or electrical shock.
Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel.
If on the following situations arises, get the equipment checked by a service personnel:
The Power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to the user's manual.
The equipment has dropped and damaged.
If the equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned, storage temperature above 60°C (140°f), it may damage the equipment.
The unit can be operated at an ambient temperature of max. 35°C.
The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A).
Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection.
• The cord set must be approved for the country in which it is used.
• The appliance coupler must have a configuration for mating with a CEE22/EN6032/IEC 320 appliance inlet.
Company
Keydata
Categories
Fax & Modem & ISDN
Model
Keydata Keynote 8320 - Green 732
Description
WiFi Driver
Operating System
Windows 95-98-Me-NT-2000
Size Driver
10.1MB
File Name
8320-minipci.exe
Observations
Manual Installation
To install the driver manually, follow the step-by-step procedures described on each individual section for a more clear installation.
Installing the ActionTec 802MR Combo Card/Realtek 8180 Wireless LAN Driver for WinXP
1. Click the "My Computer" icon and click on the "Control Panel" item to open the Control Panel.
2. Double click on the "System" icon. Click the "Device Manager" tab.
3. Click on the "Other Devices" (denoted by the yellow mark symbol), select the "Ethernet Controller" and click on the "Properties" tab.
4. From the "Ethernet Controller Properties" window, click on the "Driver" tab and select the "Update Driver" button.
5. Click on the "Specify the location of the driver (Advanced)" and again click on the "Next" button.
6. Select the "Specify a location" and click the "Browse" button to locate the disk drive of your DVD-ROM driver.
D:\Driver\MiniPCI\Actiontec802MR\Wireless\WinXP to proceed with the installation.
-----------------------------------------------------------------------------------------------------------------------------------------
Installing the Actiontec Combo/Wireless LAN Driver for WinXP
1. Click the "My Computer" icon and click on the "Control Panel" item to open the Control Panel.
2. Double click on the "System" icon. Click the "Device Manager" tab.
3. Click on the "Other Devices" (denoted by the yellow mark symbol), select the "Ethernet Controller" and click on the "Properties" tab.
4. From the "Ethernet Controller Properties" window, click on the "Driver" tab and select the "Update Driver" button.
5. Click on the "Specify the location of the driver (Advanced)" and again click on the "Next" button.
6. Select the "Specify a location" and click the "Browse" button to locate the disk drive of your DVD-ROM driver.
D:\Driver\MiniPCI\Actiontec\Wireless\WinXP to proceed with the installation.
--------------------------------------------------------------------------------------------------
Installing the Accton Combo/Wireless LAN Driver for WinXP
1. Click the "My Computer" icon and click on the "Control Panel" item to open the Control Panel.
2. Double click on the "System" icon. Click the "Device Manager" tab.
3. Click on the "Other Devices" (denoted by the yellow mark symbol), select the "Network Controller" and click on the "Properties" tab.
4. From the "Network Controller Properties" window, click on the "Driver" tab and select the "Update Driver" button.
5. Click on the "Specify the location of the driver (Advanced)" and again click on the "Next" button.
6. Select the "Specify a location" and click the "Browse" button to locate the disk drive of your DVD-ROM driver.
D:\Driver\MiniPCI\Accton\wireless to proceed with the installation.
Access to Official Website Keydata
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.