Available 10 files for Creatix CTX402 8 DSP

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Manual for V9x DSP

Information

Manual PDF

Operating System

Manual

Size Driver

614KB

File Name

manual_dsp_gb.pdf

Observations

Table of Contents
Chapter 1 INTRODUCTION ................................1-1
What is a Modem? ......................................................................................1-1
About this Modem .......................................................................................1-1
The 56K Technology....................................................................................1-2
General Description ....................................................................................1-2
Auto-Answering............................................................................................1-3
Connection Instructions...............................................................................1-3
Installation Instructions Windows ME..................................................1-3
Windows 2000...............................................1-4
Windows XP..................................................1-4
Factory Settings ..........................................................................................1-5
Manufacturer Declaration ...........................................................................1-5
Electromagnetic Conformity.........................................................................1-5
Safety Requirements ..................................................................................1-5
Chapter 2 AT COMMANDS: DATA MODEM ......2-1
Guidelines for Using AT Commands ..........................................................2-1
Modem Commands (Table standard commands).......................................2-2
AT - Attention Code ....................................................................................2-3
The ESC Sequence.....................................................................................2-4
A - Answer Mode.........................................................................................2-4
A/ - Repeat Last Command Line ................................................................2-4
D - Automatic Dialling and Dialling Parameters...........................................2-5
E – Echo Function ......................................................................................2-6
H – Switch Hook Check (Replace Handset) – Go "On Hook" ....................2-6
I – Firmware Information..............................................................................2-6
L – Volume Level.........................................................................................2-6
M – Switching the Loudspeaker On and .....................................................2-6
O – Return to online Operation....................................................................2-7
P – Select pulse dialling...............................................................................2-7
Q – Modem Messages On / Off ..................................................................2-7
S – Reading and Modifying Registers ........................................................2-7
T – Select tone dialling................................................................................2-7
V – Verbal or Numeric Modem Messages ..................................................2-7
W – Controlling Connect Messages ...........................................................2-8
X – Result Code Type/Call Progress ..........................................................2-8
Y – Long Space Disconnect .......................................................................2-9
Z – Reset Modem/Record Stored Profile ....................................................2-9

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Installation instruction under Mandrake 10

Information

Manual PDF

Operating System

Manual

Size Driver

86KB

File Name

inst-dsp-mandrake10_gb.pdf

Observations

Installation of the modem V9x DSP under Mandrake 10.0
Requirements:
- Intel driver for the modem 536ep (intel-536EP-2.56.76.0.tgz). Look at
http://linmodems.technion.ac.il/resources.html for downloading.
- Login as root and work with console
- You have to install the packages kernel-source (adequate to your kernel
version) and kdenetwork-kppp-3.1.3-37mdk for KPPP
Installation:
1. Copy the driver intel-536EP-2.56.76.0.tgz into the directory /usr/src.
2. Go into this directory /usr/src
3. Unzipped the driver with the command tar – intel-536EP-2.56.76.0.tgz
4. This will create the a new directory called intel-536EP-2.56.76.0
5. Change into this directory.
6. Set the commands
make clean
make 536
make install
If you get the error “make command not found” install the kernel-sources!
7. Now you can find the device 536ep at /dev. The driver also creates a link from
/dev/modem to /dev/536ep for using KPPP.
Configuration:
1. MINICOM:
minicom is not a package of the standard installation and has to be installed
additional. Start the program with the command minicom –s. With the arrow
keys and the return taste go to “serial port setup” and change the entry for A
into /dev/modem and for E into 115200 8 n 1 . Change these settings with
“save setup as dfl” and click on “exit”. Now the terminal program is starting and
you can communicate with modem with at commands. Check the country
settings with ATI12 and change it with the command AT+GCI=xx (xx= B4 for
UK, 7B for the Netherlands, 3D for France, B5 for USA).
0A AUT (43) Österreich – Austria
31 DNK (45) Dänemark – Denmark
3D FRA (33) Frankreich – France
04 DEU (49) Deutschland – Germany
7B NLD (31) Niederlande – The Netherlands
A6 CHE (41) Schweiz – Suisse
B4 GBR (44) Großbritanien – United Kingdom
B5 USA
Now try to make a connection with the command ATDT[phone number of a
provider][enter].
2. KPPP connection:
to configure a KPPP connection look at your distribution manual. Check the
modem init. It should be AT&F.

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Installation instruction under Mandriva 2006

Information

Manual PDF

Operating System

Manual

Size Driver

85KB

File Name

inst-dsp-mandriva2006_gb.pdf

Observations

Installation of the modem V9x DSP under Mandriva 2006
Requirements:
- Intel driver for the modem 536ep (Intel-536EP-4.71.tgz). Look at
http://developer.intel.com/design/modems/support/drivers.htm for downloading.
- Login as root and work with console
- You have to install the packages kernel-source (adequate to your kernel
version) and kdenetwork-kpppfor KPPP
Installation:
1. Copy the driver Intel-536EP-4.71.tgz into the directory /usr/src.
2. Go into this directory /usr/src
3. Unzipped the driver with the command tar – Intel-536EP-4.71.tgz
4. This will create the a new directory called intel-536
5. Change into this directory.
6. Set the commands
make clean
make 536
make install
If you get the error “make command not found” install the kernel-sources!
7. Now you can find the device 536ep at /dev. The driver also creates a link from
/dev/modem to /dev/536ep for using KPPP.
Configuration:
1. MINICOM:
minicom is not a package of the standard installation and has to be installed
additional. Start the program with the command minicom –s. With the arrow
keys and the return taste go to “serial port setup” and change the entry for A
into /dev/modem and for E into 115200 8 n 1 . Change these settings with
“save setup as dfl” and click on “exit”. Now the terminal program is starting and
you can communicate with modem with at commands. Check the country
settings with ATI12 and change it with the command AT+GCI=xx (xx= B4 for
UK, 7B for the Netherlands, 3D for France, B5 for USA).
0A AUT (43) Österreich – Austria
31 DNK (45) Dänemark – Denmark
3D FRA (33) Frankreich – France
04 DEU (49) Deutschland – Germany
7B NLD (31) Niederlande – The Netherlands
A6 CHE (41) Schweiz – Suisse
B4 GBR (44) Großbritanien – United Kingdom
B5 USA
Now try to make a connection with the command ATDT[phone number of a
provider][enter].
2. KPPP connection:
to configure a KPPP connection look at your distribution manual. Check the
modem init. It should be AT&F.

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Installation instruction under SuSe 9.2

Information

Manual PDF

Operating System

Manual

Size Driver

73KB

File Name

inst-dsp-suse92_gb.pdf

Observations

Installation of V9x under SuSE 9.2
The modem is recognized of SuSE 9.2 as intel536ep and could be configured with
this package.
To use the modem with kinternet or wvdial you have to configure it with YAST. The
link from /dev/536ep0 to /dev/modem exists so you can use it. Choose 115200 bps
for baud rate and AT&F as init1. Now you could configure your provider and then it
should be possible to get an internet connection.
Country settings:
Normally the modem is set on USA1. to change this you have to use a terminal
program like minicom.
minicom is not a package of the standard installation and has to be installed
additional. Start the program with the command minicom –s. With the arrow keys and
the return taste go to “serial port setup” and change the entry for A into /dev/modem
and for E into 115200 8 n 1 . Change these settings with “save setup as dfl” and click
on “exit”. Now the terminal program is starting and you can communicate with
modem with at commands. Check the country settings with ATI12 and change it with
the command AT+GCI=xx (xx= B4 for UK, 7B for the Netherlands, 3D for France, B5
for USA).

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Installation instrcution under SuSE 9.0 and 9.1

Information

Manual PDF

Operating System

Manual

Size Driver

90KB

File Name

inst-dsp-suse90-91_gb.pdf

Observations

Installation of the modem V9x DSP under SuSE 9.1 (Kernel 2.6.) and SuSE 9.0 (Kernel 2.4.x)
Requirements:
- Do not use the delivered driver 4.51 (in SuSE 9.0) for this modem
- Intel driver for the modem 536ep (intel-536EP-2.56.76.0.tgz). Look at
http://linmodems.technion.ac.il/resources.html for downloading.
- Install the package kernel-source (adequate to your kernel version), gcc and make
- Install the package minicom for testing the modem
- Log in as root
Installation:
1. Delete the delivered driver of SuSE 9.0 if it is installed (Delete the software package under
hardware – modem)
2. Copy the driver intel-536EP-2.56.76.0.tgz into the directory /usr/src.
3. Go into this directory /usr/src
4. Unzipped the driver with the command tar – xzvf intel-536EP-2.56.76.0.tgz
5. This will create the a new directory called intel-536EP-2.56.76.0
6. Change into this directory.
7. Set the commands
make clean
make 536
make install
If you get the error “make command not found” install the kernel-sources!
8. Now you can find the device 536ep at /dev. The driver also creates a link from /dev/modem to
/dev/536ep for using KPPP.
Configuration:
1. MINICOM:
minicom is not a package of the standard installation and has to be installed additional. Start
the program with the command minicom –s. With the arrow keys and the return taste go to
“serial port setup” and change the entry for A into /dev/modem and for E into 115200 8 n 1 .
Change these settings with “save setup as dfl” and click on “exit”. Now the terminal program is
starting and you can communicate with modem with at commands. Check the country settings
with ATI12 and change it with the command AT+GCI=xx (xx= B4 for UK, 7B for the
Netherlands, 3D for France, B5 for USA).
0A AUT (43) Österreich – Austria
31 DNK (45) Dänemark – Denmark
3D FRA (33) Frankreich – France
04 DEU (49) Deutschland – Germany
7B NLD (31) Niederlande – The Netherlands
A6 CHE (41) Schweiz – Suisse
B4 GBR (44) Großbritanien – United Kingdom
B5 USA
Now try to make a connection with the command ATDT[phone number of a provider][enter].
2. Kinternet/wvdial connection:
Configure the modem with YAST. It is important to choose “others (not recognized)”
because otherwise SuSE wants to install the package for the 4.51 driver if you choose V9x
DSP modem. Configure this entry “others” with the baud rate 115200 and the Init1 AT&F.
Then configure your provider. Now the Internet connection should function.

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Driver for V9x DSP Installation instruction included.

Operating System

Windows 2000

Size Driver

340KB

File Name

dsp-448-w2k.zip

Observations

Installation V9x DSP Data Fax Modem under Windows 2000 (4.48)

Installation Instructions
The driver can only be installed, if the PCI-Card is recognized as a new hardware, do not update existing drivers with the instruction “Update driver”.
Existing drivers has to be de-installed. De-install the device at the device manager (Control panel – System). If there is a new operating system and no driver installed, the card should be detected automatically at the device manager (Control panel – System) under “Others / unknown components / devices” as “PCI Communication Controller (simple)”.
Installation DSP under Windows 2000
1. Unpack the driver (Disc, CD or Internet) into a temporary directory.
2. After installing the card and rebooting the PC, the card will be recognized as a new hardware -> PCI Communication Controller (simple) and the hardware assistant will be started.
3. Search for -> “The best driver for the device (recommended)” and activate “Declare other sources”.
4. Here you choose the directory in which the driver has been unpacked. The file of the driver is called “…ctxs51.inf.”.
5. Confirm this message.
6. After copying the files, the hardware assistant for “Creatix V.92 DSP Data Fax Modem” can be finished.

The modem should be available at the control panel under “Telephone- and
Modem options”.
Uninstallation DSP under Windows 2000
1. Delete the entry of the modem in the device manager (control panel – system – hardware):
Creatix V9x DSP Data Fax Modem under Modems
2. Delete in the hidden directory \WINDOWS\INF the file oem*.inf (the * stand for a number, which describes the modem). The oem-files can be opened with a double click.
The file looks in the beginning as follows:
[version]
Signature = $CHICAGO$”
Class=Modem
ClassGUID={4D36E96D-E325-11CE-BFC1-08002BE10318}
Provider=%Oem%
CatalogFile=CTXH51.CAT
DriverVer=03/09/2002, 4.48.00
. . .

3. Control in the registration file (start – run – regedit) if the following entry is still existing (only this entry) and delete it.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\PCI\VEN_8086&DEV_1040&SUBSYS_10078086&REV_00

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Driver for V9x DSP Installation instruction included.

Operating System

Windows 98

Size Driver

485KB

File Name

dsp-w98.zip

Observations

Installation of the driver 4.47.2 for the Creatix Modem V9X HAM under Windows ME

Installation Instructions
The driver can only be installed, if the PCI-Card is recognized as a new hardware, do not update existing drivers
with the instruction "Update driver".
Existing drivers has to be de-installed. De-install the device at the device manager (Control panel – System). If
there is a new operating system and no driver installed, the card should be detected automatically at the device
manager (Control panel – System) under "Others / unknown components / devices" as "PCI Communication
Device (simple)".

1. Extract the driver into a temporary directory.

2. De-install the old driver (see also de-installation of the driver after this paragraph) or delete, after
a new installation of the operating system, the entry for the modem ("PCI Communication
Device") at the device manager (start – settings – control panel – system – device manager)
under "Other components".

3. Reboot your PC.

4. "Windows driver data bank will be updated".

5. "New Hardware found : PCI Communication Device". The hardware assistant will be started.

6. "PCI Communication Device" found . . . what would you like to do?" – Choose "Specify position
of the driver" and click the button "Next".

7. "Search the best driver for your device (recommended)" and activate the paragraph
"Specify position". At this point you have to specify either the directory, where you have
extracted the driver or search the position with the option "search". Important is, that you have
given the complete path. Confirm this window with "Next".

8. "Search the driver file for the following device: Creatix V9X HAM WDM Modem driver".
Driverposition: . . . \CtxH21.inf. Continue with "Next".

9. "Creatix V9X HAM WDM Modem driver. New Hardware component has been installed." Continue
with "Finish".

10. "New Hardware component found : Modem Device!"

11. The Hardware assistant will be started again. Same procedure as point 6 and 7 describes.

12. "The driver file for the following device will be searching: Creatix V.90 HAM Data Fax Modem".
Driverposition: . . .\CtxH22.inf. Continue with "Next".

13. "Creatix V9X HAM Data Fax Modem. New Hardware component has been installed". Continue
with "Finish".

14. Now an additional window of the Creatix V9X HAM WDM Modem driver opens up for choosing
the country settings "International settings". Choose the country where you use the modem and
confirm with "Ok".

15. Now the installation is finished and the modem should show up at the control panel. The country
settings can be changed under "Creatix WDM Modem Driver" at the control panel.

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Driver for V9x DSP Installation instruction included.

Operating System

Windows ME

Size Driver

407KB

File Name

dsp-448-me.zip

Observations

Installation V9x DSP Data Fax Modem under Windows ME (448)

Installation Instructions
The driver can only be installed, if the PCI-Card is recognized as a new hardware, do not update existing drivers with the instruction “Update driver”.
Existing drivers has to be de-installed. De-install the device at the device manager (Control panel – System). If there is a new operating system and no driver installed, the card should be detected automatically at the device manager (Control panel – System) under “Others / unknown components / devices” as “PCI Communication Controller (simple)”.

Installation under Windows ME
1. Unpack the driver (Disc, CD or Internet) into a temporary directory.
2. After plugging in the card and rebooting the PC, the card will be recognized as a new hardware “PCI Communication Device (simple)” and the hardware assistant will be started.
3. Choose -> “Declare the position of the driver (expand)” -> “Search for the best driver for your device” (recommended) and activate “Declare a position”.
4. Here you choose the directory in which you have unpacked the driver before. It should be the “Creatix V92 DSP WDM Modem Driver”, with the position “…\ctxs21.inf”. Finish the hardware assistant with “Finish”.
5. Another hardware component “Modem Device” will be detected. Do the same steps as before.
6. The name of the device is “Creatix V.92 DSP Data Fax Modem”, the position for that device should be “…\ctx22.inf”. Finish the hardware assistant with “Finish”.
7. The installation will be finished with the country code conversion under “Creatix V.92 DSP WDM Modem Driver” (confirm with OK).
.

Now the modem should be available at the “Control Panel” under “Modems”.
Uninstallation under Windows ME
1. Delete the entries of the modem in the device manager:
Creatix V92 DSP Data Fax Modem under modems and
Creatix V92 DSP WDM Modem driver under WDM Enumerator.

2. Delete the entries in the hidden directory /Windows/Inf /Others:
Creatix Polymedia GmbHCTXs21.inf and
Creatix Polymedia GmbHCTXs22.inf.

Control in the registration file (start – run – regedit) if the following entries are still existing (only these entries) and delete them.
HKEY_LOCAL_MACHINE\Enum\PCI\VEN_8086&DEV_1040&SUBSYS_10078086&REV_00
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class\WDM_MODEM\0000

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Driver for V9x DSP Installation instruction included.

Operating System

Windows NT4

Size Driver

757KB

File Name

dsp-448-nt.zip

Observations

Installation of V9c DSP Data Fax Modem under Windows NT 4.0
Installation:

1. Unzip the file DSP_448_NT.zip into a temporary directory.

2. Start the program installer.exe in this directory.

3. Click on JA/YES at the message if you want to install the Creatix V9x DSP Data Fax Modem.

4. After some time the message appears that the modem is installed. Click on OK.

5. Now the modem is installed at Control Panel – Modems.
At Programs – Creatix Polymedia GmbH you can find the tool Intels41 for setting the country code. Please set your country code.

6. For using the dial-up-networking the RAS Service must be installed and configured. Also you should install service packs new.

Un-installation:

To uninstall the modem go to Control Panel – Software. Activate the entry Creatix V9x DSP Data Fax Modem and click on Add/Delete. Click on JA/YES at the question if you want to uninstall the modem. The next message confirm with OK. Now you get shown the entry of the modem at Control Panel – Modems. Click on Delete and then on YES for uninstall the modem.

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX402 8 DSP

Description

Driver for V9x DSP Installation instruction included.

Operating System

Windows XP-Vista

Size Driver

712KB

File Name

dsp-47783-xp-vista.zip

Observations

Installation V9x DSP Data Fax Modem under Windows XP (4.67.3)

Installation Instructions
The driver can only be installed, if the PCI-Card is recognized as a new hardware, do not update existing drivers with the instruction “Update driver”. Existing drivers has to be de-installed. De-install the device at the device manager (Control panel – System). If there is a new operating system and no driver installed, the card should be detected automatically at the device manager (Control panel – System) under “Others / unknown components /devices” as “PCI Communication Device (simple)”.

Installation under Windows XP
1. Unpack the driver (Disc, CD or Internet) into a temporary directory.
2. After installing the card and rebooting the PC, the card should be recognized as a new hardware -> PCI Communication Device (simple) and the hardware assistant will be started.
3. Choose “Install software from a list or from another source” (advanced user) and activate “Search for the best driver”.
4. At the point “Search also the following sources”, declare the directory in which you have unpacked the driver at the beginning.
5. You should find “Creatix V.9x DSP Data Fax Modem”. Finish the hardware assistant after copying the files with “Finish”.

The modem should be available at the control panel under “Telephone- and Modem options” (printer and other hardware).

Uninstallation under Winsow XP

For uninstalling go to Control Panel – Software and delete the entry for the modem Creatix V9x DSP Data Fax Modem

Uninstalling step-by-step if there are problems
1. Delete the entry of the modem in the device manager (control panel – system – hardware):
Creatix V9x DSP Data Fax Modem
2. Delete in the hidden directory \WINDOWS\INF the file oem*.inf (the * stand for a number, which describes the modem). The oem-files can be opened with a double click.
The file looks in the beginning as follows:
[version]
Signature = $CHICAGO$”
Class=Modem
ClassGUID={4D36E96D-E325-11CE-BFC1-08002BE10318}
Provider=%Oem%
CatalogFile=CTXH51.CAT
DriverVer=04/22/2004, 4.67.3
. . .

3. Control in the registration file (start – run – regedit) if the following entry is still existing (only this entry) and delete it.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\PCI\VEN_8086&DEV_1040&SUBSYS_104016BE&REV_00