Conceptronic CMC4 Fax & Modem & ISDN

Company

Conceptronic

Categories

Fax & Modem & ISDN

Model

Conceptronic CMC4

Description

Drivers

Operating System

Windows 2000

Version

1.0

Size Driver

2.3MB

File Name

w2kmult.exe

Observations

Readme2k V1.1 - MultiCom
--------------------------------------------------------------------
Edited by D. Slagers
DS/26-05-2000
2L International BV
1st public beta release for Multicom
---------------------------------------------------------------------
Known issues:

- Dialback for ISDN does not function
- MSN / Callerparty for ISDN cannot be used
- Switch type not standard EuroISDN (EDDS1)
- Use only manual switch from ISDN/MODEM/GSM
- Analog modem can cause BSOD and reboot. (under investigation)
- Activating ISDN line can be difficult / switch from ISDN to modem
And back.
---------------------------------------------------------------------

QUICK START INSTALLATION GUIDE FOR WINDOWS 2000

Congratulations on your purchase of the MultiCom.
This quick start installation aims to get you using the product in the shortest possible time.
If you have purchases the XP-Modem; XP-ISDN; or XP-GSM upgrade kits this guide will also show you how to install them.

Installing MultiCom drivers using CD-ROM:
(1) Insert the MultiCom into an available PCMCIA (Type II or III) slot. Windows 2000 will detect the MultiCom and pop up "Welcome to the Found New Hardware Wizard" dialog box. Click on "Next>" to let the wizard search for the drivers.

(2) Select "Search for the best driver for your device (Recommended)", click on "Next>" again. Choose CD-ROM drive as the option for installation.

(3) Insert the MultiCom Installation CD-ROM into the CD-ROM drive; then click on "Next" to continue. The Wizard will read the installation information file in the CD-ROM and display a dialog box showing that it has found a driver for the device.

(4) Click on "Next>", the Wizard will start to copy some file. Next, the dialog box "Completing the Found New Hardware Wizard" will appear. Click "Finish" and Windows 2000 will start to add the following Multifunction devices that its has found:
- WAVEXA XP-BUS Controller
- MultiCom XP-LAN Ethernet Adapter
- MultiCom XP-ISDN Adapter

(5) If there are dialog boxes "Digital Signature Not Found" appear, click "Yes" to continue the installation.

(6) First half of the installation has completed.

(7) Second half of installation can be launch by clicking on the "Start" button and run d:\Win2k\setup (assuming that d: is your CD-ROM drive). Click on "Next>" to continue.

(8) WAVEXA Setup will install MultiCom 56K Modem and MultiCom GSM Modem. If there are dialog boxes "Digital Signature Not Found" appear, click "Yes" to continue the installation.

(9) Once "Installation Completed" dialog appear, it indicate that the second half of installation has end and reboot of system is needed.

(10) Click on "Finish" to restart Windows. You will have to configure your MultiCom XP-LAN Adapter before accessing the network. On network configuration, please consult your system administrator.
Setting MultiCom Modem Country Type
(1) Click on the WAVEXA diagnostic icon in Control Panel.

(2) Insert modem NSAU (Dongle).

(3) In the Modem property page, click on "Configure" button to select the country where you are dialing from. Choose the country and click on "OK" button to confirm it.
Note: Please make use of the WAVEXA diagnostic program in Control Panel to configure or test the various functions. For more information, please refer to the user manual in the CD-ROM.

Company

Conceptronic

Categories

Fax & Modem & ISDN

Model

Conceptronic CMC4

Description

Drivers

Operating System

Windows NT4

Version

1.06

Size Driver

2.5MB

File Name

mltnt106.exe

Observations

README.TXT - MultiCom
---------------------------------------------------------------------
Please take the time to review this file before installing and using

INSTALLATION
------------
1. Insert PCMCIA card in an available slot in your notebook, do not
connect the any NSAU to either of the ports.

2. Run a:\setup, the setup will continue until clicking finish to
reboot system.

3. Add "MultiCom XP-LAN Ethernet Adapter"
. Click "Network" under Control Panel, Click "Add" under "Adapters"
Table
. Click "Have Disk", make sure Disk3 inside the floppy drive
. Type in A:\LAN and Click "OK"
. The Miscrosoft TCP/IP Properties Dialog appear, please fill in
your IP address and Subnet MASK such as 255.255.255.0
. The XPLAN Ethernet Adapter install is finished, please choose not
to restart the system

4. Add "MultiCom XP-ISDN Adapter"
. Click "Network" under Control Panel, Click "Add" under "Adapters"
Table
. Click "Have Disk", make sure Disk3 inside the floppy drive
. Type in A:\ISDN and Click "OK"
. The Miscrosoft TCP/IP Properties Dialog appear, please fill in
your IP address and Subnet MASK such as 255.255.255.0
. The ISDNWAN install is finished, please restart system

UNINSTALL
---------
1. Remove "MultiCom XP-ISDN Adapter"
. Click "Network" under Control Panel, choose Adapters Table
. Highlight "MultiCom XP-ISDN Adapter" and Click "Remove"

2. Remove "MultiCom XP-LAN Ethernet Adapter"
. Click "Network" under Control Panel, choose Adapters Table
. Highlight "MultiCom XP-LAN Ethernet Adapter" and Click "Remove"

3. Remove V.90 Modem, registery and files
. Click "Add/Remove Programs"
. Highlight "MultiCom Release 1.xx" and click "Remove"
4. Reboot System

Access to Official Website Conceptronic

Home English Home German

Welcome to the HelpDrivers, driver for printers.

Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more

You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.

Do not rename the file you're downloading, it may cause installation problems.

Available 3 files for Conceptronic CMC4

Select Files