Kyocera LDC-870 Download Drivers

Available 3 files for LDC-870
Company
Kyocera
Categories
Printers
Model
Kyocera LDC-870
Description
Print Drivers
Operating Systems
Windows 95-98
Size Driver
1.2Mb
File Name
ldc800w9598.exe
Information
1. Foreword
This printer driver is compatible for use with
Microsoft(r) Windows(tm) 95/98.

2. Recommended computer environment
System software: Microsoft Windows 95/98
Hardware: PC/AT compatible computer
Minimum 66MHz 486DX CPU
Minimum 8MB installed RAM
5MB free hard disk space
2-way parallel cable
Compatible printer: Mita LDC/Ti 800 Duplex Series

3. Installing the printer driver software
To use this unit as a printer, it is first necessary to install the
Mita LDC/Ti 800 Duplex Series printer driver in your computer.
1) Start up Windows 95/98.
Quit all other applications that may be open.
2) Insert the Windows 95/98 Printer Driver Installer Disk into
a Floppy Drive.
3) Click on [Start] in the Task Bar.
4) Use the mouse to point to [Settings] and click on
[Printers] in the submenu which is displayed.
5) The [Printers] folder will open. Double-click on the [Add
printer] icon.
6) Continue the installation procedure by following each of the
steps described on-screen.
7) The Mita LDC/Ti 800 Duplex Series will be designated as the
default printer in the [Set As Default] setting.

4. Removing the printer driver software
1) Start up Windows 95/98.
Quit all other applications that may be open.
2) Click on [Start] in the Task Bar. Use the mouse to point to
[Settings] and click on [Printers] in the submenu that is
displayed.
3) Use the right mouse button to click on the
[Mita LDC/Ti 800 Duplex Series] icon and then click on [Delete].
4) Continue the removal procedure by following each of the steps
described on-screen.

5. Cautions for use
1) If any another printer driver is installed in your computer, it
is possible that printing will not be accomplished correctly. If
you experience trouble, remove the other printer driver and then
attempt to print once again. Refer to the instruction manual of
the other printer driver for details on removal.
2) If the Mita LDC/Ti 800 Duplex Series is selected as a network
printer during installation of the printer driver, a message will
appear which tells you that the "MFC40.TMP" and "MSVCRT40.TMP"
files could not be found. At this point, click on [Skip] to
continue the installation procedure.
3) The [General] and [Separate Page] menus will be displayed when
you use the Mita LDC/Ti 800 Duplex Series, but neither of them
will be functional.
4) Even if [Start printing after 1st page is spooled] is selected,
it will not be functional and a system error message
(insufficient memory) may appear. In this case, lower the
printing resolution or select [Start printing after last page is
spooled], and then attempt to print once again.
5) The [Spool MS-DOS print job] and [Check port state before
printing] sub-menus will be displayed in the [Detail] and [Port
setting...] menus when you use the Mita LDC/Ti 800 Duplex Series,
but neither of them will be functional.
6) If printing troubles develop, first cancel the print job
currently in progress and then turn the power to the printer OFF
and then ON again. Then attempt to print once again. If the
trouble persists, contact your service representative, an
authorised service centre or the place of purchase.
7) Depending upon the application in use, if there is insufficient
space on your hard disk or insufficient RAM installed in your
computer, printing may be terminated prior to completion.
In this case, free up space on your hard disk or add memory to
your computer, as appropriate, and try to print again.
Company
Kyocera
Categories
Printers
Model
Kyocera LDC-870
Description
Print Driver Disk 1
Operating Systems
Windows NT4
Size Driver
1Mb
File Name
ldc800nt1.exe
Information
1. Foreword
This printer driver is compatible for use with Microsoft(r) Windows
(tm) NT4.0.

2. Recommended computer environment
System software: Microsoft Windows NT4.0
Hardware: PC/AT compatible computer
Minimum 33MHz 486DX CPU
Minimum 8MB installed RAM
10MB free hard disk space
2-way parallel cable
Compatible printer: Mita LDC/Ti 800 Duplex Series

3. Installing the printer driver software
In order to actually print out from your printer,
it is necessary to install the Mita LDC/Ti 800 Duplex Series printer
driver in your Windows environment.

Cautions for use
Service Pack 3 must be installed under Windows NT before
installation of the printer driver. If it has not been installed,
install Service Pack 3 before installing the printer driver.

1) Start up Windows NT and quit all other applications that may
be open.
2) Insert the Windows NT Printer Driver Installer Disk 1 into
a floppy disk drive.
3) Click on [Start].
4) Point to [Run...], type in "a:\setup" and click on [OK].
5) Continue the installation procedure by following each of
the steps described on-screen.
6) Insert the Windows NT Printer Driver Installer Disk 2
into the floppy disk drive and click on [OK].
7) Once installation is complete, restart your computer.
8) Set the Mita LDC/Ti 800 Duplex Series printer as the
[Default printer].

4. Removing the printer driver software
1) Start up Windows NT and quit all other applications
that may be open.
2) Carry out the procedure to [Add/Remove Programs]
in the [Control Panel].
3) Select [Mita LDC/Ti 800 Duplex Series] in the list of installed
applications that is displayed in the window to add and
remove applications.
4) Click on [Add/Remove...].
5) Once the printer name is deleted from the list,
restart your computer.

5. Cautions during printing
1) If any another printer driver is installed in your computer,
it is possible that printing will not be accomplished correctly.
If you experience trouble, remove the other printer driver
and then attempt to print once again. Refer to the instruction
manual of the other printer driver for details on removal.
2) The [General] and [Separate Page] menus will be displayed when
you use the Mita LDC/Ti 800 Duplex Series, but neither of them
will be functional.
3) Even if [Start printing after 1st page is spooled] is selected,
it will not be functional and a system error message
(insufficient memory) may appear. In this case, lower the
printing resolution or select [Start printing after last page is
spooled], and then attempt to print once again.
4) The [Spool MS-DOS print job] and [Check port state before
printing] sub-menus will be displayed in the [Detail] and [Port
setting...] menus when you use the Mita LDC/Ti 800 Duplex Series,
but neither of them will be functional.
5) If printing troubles develop, first cancel the print job
currently in progress and then turn the power to the printer OFF
and then ON again. Then attempt to print once again. If the
trouble persists, contact your service representative, an
authorised service centre or the place of purchase.
Company
Kyocera
Categories
Printers
Model
Kyocera LDC-870
Description
Print Driver Disk 2
Operating Systems
Windows NT4
Size Driver
461Kb
File Name
ldc800nt2.exe
HelpDrivers Since March 2000