Available 3 files for Fargo Pro-L
Select Files
Company
Fargo
Categories
Printers
Model
Fargo Pro-L
Description
Drivers
Operating System
Windows 3.x
Version
4.3.2
Size Driver
319KB
File Name
prol31.exe
Observations
Smart Card Commands
Commands to printer (in command mode):
Name Actual Code Description
ESC - S0 $1B $00 $02 $53 $30 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot and to be returned
or ejected based on the input from the two control inputs.
ESC - S1 $1B $00 $02 $53 $31 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot
and return when there is data present in the parallel port.
ESC - i $1B $00 $02 $69 Card Infeed to printing station, encode if primed.
This command feeds a card from the card hopper to the printing station.
If there is already a card at the printing station, no new card is fed.
Use this command after the ESC - S1 command.
ESC - e $1B $00 $02 $65 Card eject from printing station.
This command ejects a card from the printing station.
Use this command to eject a bad card after using the ESC - S1 command.
Print $1B $00 $FF . . . Start-of-Graphics command, enter print mode.
This command causes the printer to leave command mode and enter print mode.
The first thing that the printer will do is feed a card as if it had received
the ESC - i command. Encoding will be done if primed. The printer will print
the card and return to command mode when the card is ejected.
Typical command sequences:
TOP0:
send ESC - S0 // Prime for smart card, using control inputs.
send Print // Feed card and put in smart card slot.
wait for control inputs to be received.
if the smart card is to be ejected
input /pin5 and /pin9 // Card will be ejected with an error.
goto TOP0 // The reprint feature rewinds the buffer to do this for you.
else input /pin9 // Card will be returned to printing station.
continue print
end if
end
TOP1:
send ESC - S1 // Prime for smart card, not using control inputs.
send ESC - i // Feed card and put in smart card slot.
wait for next byte from parallel port.
if the smart card is to be ejected
send ESC - e // Eject bad card.
goto TOP1 // Repeat sequence if you want to try again.
else send Print // Enter print mode if printing is required.
end if
end
New Smart Card Connections
The 9-pin connector at the rear of the printer is now wired directly to the smart card receptacle
without going through the printer's P. C. board first. Only the signals that the printer needs
to monitor are connected to the printer's P. C. board.
The 9-pin Sub-D connector is connected directly to the smart card receptacle board as before:
X. Cut wire (ribbon cable wire #1) connected to GND on the smart card receptacle board.
1. /SW - Switch closure to GND to indicate card-in-place.
2. C5 - GND supply for system, ground reference for /SW.
3. C6 - smart card line.
4. C7 - smart card line.
5. C8 - smart card line, monitored by printer as FNB or /Error signal (mode S0).
6. C1 - smart card line.
7. C2 - smart card line.
8. C3 - smart card line.
9. C4 - smart card line, monitored by printer as FNA or /Done signal (mode S0).
Company
Fargo
Categories
Printers
Model
Fargo Pro-L
Description
Drivers
Operating System
Windows 95-98-Me
Version
4.4.0
Size Driver
366KB
File Name
prol95.exe
Observations
Smart Card Commands
Commands to printer (in command mode):
Name Actual Code Description
ESC - S0 $1B $00 $02 $53 $30 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot and to be returned
or ejected based on the input from the two control inputs.
ESC - S1 $1B $00 $02 $53 $31 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot
and return when there is data present in the parallel port.
ESC - i $1B $00 $02 $69 Card Infeed to printing station, encode if primed.
This command feeds a card from the card hopper to the printing station.
If there is already a card at the printing station, no new card is fed.
Use this command after the ESC - S1 command.
ESC - e $1B $00 $02 $65 Card eject from printing station.
This command ejects a card from the printing station.
Use this command to eject a bad card after using the ESC - S1 command.
Print $1B $00 $FF . . . Start-of-Graphics command, enter print mode.
This command causes the printer to leave command mode and enter print mode.
The first thing that the printer will do is feed a card as if it had received
the ESC - i command. Encoding will be done if primed. The printer will print
the card and return to command mode when the card is ejected.
Typical command sequences:
TOP0:
send ESC - S0 // Prime for smart card, using control inputs.
send Print // Feed card and put in smart card slot.
wait for control inputs to be received.
if the smart card is to be ejected
input /pin5 and /pin9 // Card will be ejected with an error.
goto TOP0 // The reprint feature rewinds the buffer to do this for you.
else input /pin9 // Card will be returned to printing station.
continue print
end if
end
TOP1:
send ESC - S1 // Prime for smart card, not using control inputs.
send ESC - i // Feed card and put in smart card slot.
wait for next byte from parallel port.
if the smart card is to be ejected
send ESC - e // Eject bad card.
goto TOP1 // Repeat sequence if you want to try again.
else send Print // Enter print mode if printing is required.
end if
end
New Smart Card Connections
The 9-pin connector at the rear of the printer is now wired directly to the smart card receptacle
without going through the printer's P. C. board first. Only the signals that the printer needs
to monitor are connected to the printer's P. C. board.
The 9-pin Sub-D connector is connected directly to the smart card receptacle board as before:
X. Cut wire (ribbon cable wire #1) connected to GND on the smart card receptacle board.
1. /SW - Switch closure to GND to indicate card-in-place.
2. C5 - GND supply for system, ground reference for /SW.
3. C6 - smart card line.
4. C7 - smart card line.
5. C8 - smart card line, monitored by printer as FNB or /Error signal (mode S0).
6. C1 - smart card line.
7. C2 - smart card line.
8. C3 - smart card line.
9. C4 - smart card line, monitored by printer as FNA or /Done signal (mode S0).
Company
Fargo
Categories
Printers
Model
Fargo Pro-L
Description
Drivers
Operating System
Windows NT-2000-XP
Version
2.0.2
Size Driver
196KB
File Name
prolnt.exe
Observations
Smart Card Commands
Commands to printer (in command mode):
Name Actual Code Description
ESC - S0 $1B $00 $02 $53 $30 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot and to be returned
or ejected based on the input from the two control inputs.
ESC - S1 $1B $00 $02 $53 $31 Smart Card primer, follow with ESC - i or Printing.
This command causes the card to be put into the smart card slot
and return when there is data present in the parallel port.
ESC - i $1B $00 $02 $69 Card Infeed to printing station, encode if primed.
This command feeds a card from the card hopper to the printing station.
If there is already a card at the printing station, no new card is fed.
Use this command after the ESC - S1 command.
ESC - e $1B $00 $02 $65 Card eject from printing station.
This command ejects a card from the printing station.
Use this command to eject a bad card after using the ESC - S1 command.
Print $1B $00 $FF . . . Start-of-Graphics command, enter print mode.
This command causes the printer to leave command mode and enter print mode.
The first thing that the printer will do is feed a card as if it had received
the ESC - i command. Encoding will be done if primed. The printer will print
the card and return to command mode when the card is ejected.
Typical command sequences:
TOP0:
send ESC - S0 // Prime for smart card, using control inputs.
send Print // Feed card and put in smart card slot.
wait for control inputs to be received.
if the smart card is to be ejected
input /pin5 and /pin9 // Card will be ejected with an error.
goto TOP0 // The reprint feature rewinds the buffer to do this for you.
else input /pin9 // Card will be returned to printing station.
continue print
end if
end
TOP1:
send ESC - S1 // Prime for smart card, not using control inputs.
send ESC - i // Feed card and put in smart card slot.
wait for next byte from parallel port.
if the smart card is to be ejected
send ESC - e // Eject bad card.
goto TOP1 // Repeat sequence if you want to try again.
else send Print // Enter print mode if printing is required.
end if
end
New Smart Card Connections
The 9-pin connector at the rear of the printer is now wired directly to the smart card receptacle
without going through the printer's P. C. board first. Only the signals that the printer needs
to monitor are connected to the printer's P. C. board.
The 9-pin Sub-D connector is connected directly to the smart card receptacle board as before:
X. Cut wire (ribbon cable wire #1) connected to GND on the smart card receptacle board.
1. /SW - Switch closure to GND to indicate card-in-place.
2. C5 - GND supply for system, ground reference for /SW.
3. C6 - smart card line.
4. C7 - smart card line.
5. C8 - smart card line, monitored by printer as FNB or /Error signal (mode S0).
6. C1 - smart card line.
7. C2 - smart card line.
8. C3 - smart card line.
9. C4 - smart card line, monitored by printer as FNA or /Done signal (mode S0).
Access to Official Website Fargo
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.