eTurboTouch Turbo Pen Download Drivers

This notice is for eTurboWare V1.00build 0615 for Mac 9.1 OS , it’s only compatible with eTurbo Touch T4/T6 USB controller .

A. you may copy the file “ eTurbo Ware Installer “ to Mac , the file maby cannot show full name in Mac 9.1.
B. unzip file by “ Stuffit Expander “ , this will create an “eTurbo ware installer “ shortcut on desk top .
C. click the installer shortcut to install driver .
D. you may choose the forder or create a new one for save eTurbo Ware’s files while installing , it will create an “ eTurbo Ware “ shortcut on desk top .
E. after installation completed , it’s not necessary re-boot Mac to launch driver .
F. click the eTurbo Ware short cut to launch touch control panel , the first page of panel will showing the controller type & firmware version of controller .
G. you may launch calibration function by choose the calibrate page .
H. if the controller is an brand new controller , we strongly recommend it’s have to do 5 point calibration first before start to using touch function .
I. you may do the 25 point calibration only when the accuracy is not fit your request , the 25 point data will showing on the “ memory info “ page , you can clear it by press clear button then press “ download “ button .
J. please don’t type any word in the “ terminal emulator “ page unless you’re familiar the controller command set , this is only for expert of firmware engineer use .

Platform.reg.......... Setting only for a build image that will run on a x86 PC
=======================================================================================
IF BSP_NOSERIAL !
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial]
;+01
"SysIntr"=dword:14
"IoBase"=dword:03F8
;+01
;-01 "SysIntr"=dword:13
;-01 "IoBase"=dword:02F8
"IoLen"=dword:8
"DeviceArrayIndex"=dword:0
"Prefix"="COM"
"Dll"="Com16550.Dll"
"Order"=dword:0
"Priority"=dword:0

[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial\Unimodem]
"Tsp"="Unimodem.dll"
"DeviceType"=dword:0
"FriendlyName"=LOC_FRIENDLYNAME_SERIAL
"DevConfig"=hex: 10,00, 00,00, 05,00,00,00, 10,01,00,00, 00,4B,00,00, 00,00, 08, 00, 00, 00,00,00,00
ENDIF ; BSP_NOSERIAL

IF BSP_SERIAL2
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial2]
;+01
"SysIntr"=dword:13
"IoBase"=dword:02E8
;+01
;-01 "SysIntr"=dword:14
;-01 "IoBase"=dword:03E8
"IoLen"=dword:8
"DeviceArrayIndex"=dword:1
"Prefix"="COM"
"Dll"="Com16550.Dll"
"Order"=dword:0

[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial2\Unimodem]
"Tsp"="Unimodem.dll"
"DeviceType"=dword:0
"FriendlyName"=LOC_FRIENDLYNAME_SERIAL2
"DevConfig"=hex: 10,00, 00,00, 05,00,00,00, 10,01,00,00, 00,4B,00,00, 00,00, 08, 00, 00, 00,00,00,00
ENDIF

=======================================================================================
;Project.BIB <=== Please add following setting to this file before you build the image
;Following setting assume you copy eTouch.dll,Touch32Ex.dll,eTurboWare.exe and TouchTray.exe
;under the directory D:\WinCE\X86
=======================================================================================
MODULES
eTouch.dll D:\WinCE\X86\eTouch.dll NK SH
Touch32Ex.dll D:\WinCE\X86\Touch32Ex.dll NK SH
eTurboWare.exe D:\WinCE\X86\eTurboWare.exe NK S
TouchTray.exe D:\WinCE\X86\TouchTray.exe NK S

FILES
eTurboWare.lnk D:\WinCE\InstallSource\X86RELEASE\eTurboWare.lnk NK S
TouchTray.lnk D:\WinCE\InstallSource\X86RELEASE\TouchTray.lnk NK S

1. Preface ..............................................................................................5
Introduction...................................................................................................................5
Installation...................................................................................................................6
Uninstall the Software.................................................................................................6
Support Services...........................................................................................................7
2. Using eTurboWare.............................................................................8
Using eTurboWare.......................................................................................................8
Controller List ..............................................................................................................9
Calibrating Your Screen..........................................................................................10
2-Point Calibration.......................................................................................11
5-Point Calibration.......................................................................................12
25-Point Calibration .....................................................................................13
Draw Test Window ........................................................................................14
Touch Setting.............................................................................................................15
Touch Mode....................................................................................................16
Right Click Tool.............................................................................................16
Touch Sound...................................................................................................17
Double Click ...................................................................................................17
25pt Parameters........................................................................................................17
eTurboWare Mouse Icon..........................................................................................18
On-Line Help .............................................................................................................18
Exiting the eTurboWare...........................................................................................19
3. Troubleshooting ..............................................................................20
Important Notice.......................................................................................................20
Q & A ..........................................................................................................................21
Introduction
eTurboWare converts the data from the touch panel to emulate input from a
mouse device. eTurboWare for Windows is the software for the eTurboTouch
touch panel. It provides full touch panel functionality for all applications running
under Microsoft Windows 9X, Windows NT and WindowsMe.
After you finished installing eTurboWare, you can select and drag objects using
the touch panel. To make a selection, simply touch the screen slightly.
This manual provides the following information and will be described later by
chapters.
n Install this software
n Use the touch panel (control panel) to customize your work environment
n Troubleshooting

Installation
To install the eTurboWare for Windows9X and WindowsMe, please follow the
steps below:
1. Make sure that there are no other applications open.
2. Insert the eTurboWare CD into your CD-ROM drive.
3. From the Start Menu, select “Run” and browse to the folder to choose
“Setup.exe” file.
4. The setup program starts. A welcome message appears. Click “Next”. Please
follow the onscreen instructions to install the application software.
5. After the installation is finished, please restart your system to let Windows
detect and load driver automatically.