Exsys EX-44098 Download Drivers and Manual

Available 2 files for EX-44098
Company
Exsys
Categories
Other Peripherals
Model
Exsys EX-44098
Description
PCI-Express 8S Serial RS-232 card (Oxford)
Operating Systems
Manual
Size Manual
314Kb
File Name
ex-44098.pdf
Info
HARDWARE INSTALLATION :
Attention! Do not install the card before running the setup utility. Please install
the drivers for the card first. If not the card might not be installed correctly!!! If
you already do install the drivers please proceed with the following Instructions.
If you are ready with the jumper settings, please proceed with the following installation
instructions. Because the designs of computers are different, only general installation
instructions are given. Please refer your computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Computer
and gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of your
computer. Make sure it is the right expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make
sure the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer’s cover and the mounting screws.

DRIVER INSTALLATION :
Windows 9x/ME/2000/XP & Vista:
After starting Windows it recognizes a new “PCI Controller“ and opens the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating
system “95_98_ME“ “2000“ “XP32“ “XP64“ “Vista32“ or “Vista64“ into the box for
the Path/Source and click at >next/continue<. Now Windows searches for the drivers
in the specified directory. Follow the hardware assistant and finish the installation. If
Windows recognizes other new devices repeat the above described steps. Attention!
Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows
that opens select >Device Manager<. Under „Ports (COM and LPT)“ you should find
a new „PCI Port“ as sample (LPT2) or (Com3). If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example COM 3 to COM5, open the >Device
Manager< click at >COM3<, >Settings< and then >Advance<. There you can change
between COM 3 till 256. The LPT Ports can be changed in the same way!
Windows Server 2000/2003:
After starting Windows it recognizes a new “PCI Controller“ and opens the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating
system for Server 2000: “2000“ and for Server 2003: “XP32“ or “XP64“ into the box
for the Path/Source and click at >next/continue<. Now Windows searches for the
drivers in the specified directory. Follow the hardware assistant and finish the installation.
If Windows recognizes other new devices repeat the above described steps.
Attention! Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows
that opens select >Device Manager<. Under „Ports (COM and LPT)“ you should find
a new „PCI Port“ as sample (LPT2) or (Com3). If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example COM 3 to COM5, open the >Device
Manager< click at >COM3<, >Settings< and then >Advance<. There you can change
between COM 3 till 256. The LPT Ports can be changed in the same way!
Windows NT 4.0:
Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:).
Click at >Start< >Run< and enter „D:\IO\OXFORD\NT4\Install_Serial.exe" then click
>OK<. Windows NT will now start the setup program and install the driver. Please
Restart Windows NT after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at >Start< >Programs< >Administrative Tools[Common]< >Windows NT-
Diagnostics< then click at >Resource< >IRQ<. Here you should find the entry „09
oxser 0 PCI“. Then click at >I/O-Port< here you should see the entries „D400-D407
oxser 0 PCI“ „D800-D802 oxser 0 PCI“ and „DC00-DC1F oxser 0 PCI“
for the ports. The I/O addresses can change depends which system and card is installed.
If you see these or similar entry's the card is installed correctly.
LINUX:
There are no drivers available for Linux, but the card is supported by the most versions
of Linux. Because each individual distribution and kernel version of Linux is different,
sadly we cant provide a installation instruction. Please refer to the installation manual
for standard IO ports from your Linux version! In some newer versions the card will
even be installed automatically after starting Linux.
Company
Exsys
Categories
Other Peripherals
Model
Exsys EX-44098
Description
PCI-Express 8S Serial RS-232 card (Oxford)
Operating Systems
Windows 98-98Se-Me-NT4-2000-XP-2003-Vista-Linux
Size Driver
1.5Mb
File Name
ex-44098.zip
Info
Windows Vista 32 / 64 bit User Manual
Revision 0.1
Table of Contents
1. INTRODUCTION 2
2. OBTAINING DRIVER 2
3. DRIVER INSTALLATION 2
4. VERIFYING DRIVER INSTALLATION 5
5. SERIAL PORT PROPERTIES SHEET: 5
6. SERIAL PORT FEATURES AND MODE CHANGES: 9
7. DIRECT MEMORY ACCESS (DMA): 14
8. PARALLEL PORT FEATURES AND MODE CHANGES: 15
9. USB MODE: 16
10. UNINSTALLING DRIVERS: 16
11. SUGGESTIONS / SUPPORT: 17

=========================================================================

DOS Driver Installation User Manual
Table of Contents
1. Description:........................................................................................................................................1
2. Contents available with Moschip DOS Driver Disk:........................................................................1
3. Options:..............................................................................................................................................1
4. Installation Procedure:.....................................................................................................................2
5. Loop back connections:...................................................................................................................6
Revision history.........................................................................................................................................6
1. Description:
This document provides the information about how to install the serial and parallel drivers for MosChip MCS9901 PCIe to Serial and Parallel I/O ports on DOS 6.22 environment. Normally any serial and parallel I/O ports can be supported by BIOS call services in DOS environment. However DOS supports only 4 serial ports and 3 parallel ports.
HelpDrivers Since March 2000