Available 6 files for Comtrol VS2000 v.34
Select Files
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
Device Driver
Operating System
Citrix WinFrame 1.6
Version
2.35
Size Driver
372KB
File Name
1800002b.exe
Observations
Do NOT install this driver in Windows 2000/XP operating systems Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS
Use this file to install the Comtrol software. This readme
file covers:
- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information
VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.
VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.
This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES
This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER
Comtrol recommends removing older versions of the driver
before installing new releases.
1. Open the Control Panel and start the Network applet.
2. Select the Adapters tab.
3. Highlight Comtrol VS1000/VS2000.
4. Click the Remove button.
5. Close the Network applet.
6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER
After you have extracted the driver files, follow these steps:
1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.
2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.
3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.
4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
Device Driver
Operating System
Citrix WinFrame 1.7
Version
2.35
Size Driver
372KB
File Name
1800002b.exe
Observations
Do NOT install this driver in Windows 2000/XP operating systems Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS
Use this file to install the Comtrol software. This readme
file covers:
- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information
VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.
VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.
This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES
This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER
Comtrol recommends removing older versions of the driver
before installing new releases.
1. Open the Control Panel and start the Network applet.
2. Select the Adapters tab.
3. Highlight Comtrol VS1000/VS2000.
4. Click the Remove button.
5. Close the Network applet.
6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER
After you have extracted the driver files, follow these steps:
1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.
2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.
3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.
4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
AT Command Set
Information
Manual PDF
Operating System
Manual
Version
B
Size Driver
265KB
File Name
2000052b.pdf
Observations
Also contains +MS AT command information. AT Command Set for
RocketModem Series, VS2000, and
RocketPort USB Modem Hub
Overview
This document discusses the following topics. Blue underlined text denotes hypertext links.
• Basic AT commands
• ECC Commands
• MNP 10 Commands
• W-Class Commands
• Fax Class 1 Commands
• Fax Class 2 Commands
• Error Control and Synchronous Mode Selection (+ES) (RocketPort USB Modem Hub, only)
• Select Modulation (+MS)
• AT Command Result Codes
• S-Register Summary
• Factory Defaults
• S-Register Definitions
Basic AT Commands
The following table lists the AT commands recognized by Comtrol V.34 and V.90 modems. For more detailed
descriptions of these commands, see the RC336D/RC336LD (V.34) and RC56D/RC56LD (V.90)
Select Modulation (+MS)
This extended-format AT command uses one to five subparameters to:
• Select the modulation.
• Optionally, enable or disable automode.
• Specify the lowest and highest connection rates.
• Select m-Law or A-Law codec type.
• Enable or disable robbed bit signaling generation (server modem) or detection (client modem.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
Software Installation
Information
Manual PDF for Windows NT 3.51
Operating System
Manual
Version
A
Size Driver
776KB
File Name
0000_a.pdf
Observations
Table of Contents
List of Tables
Introduction
Scope ...................................................................................................... 9
Operating System Requirements .................................................... 9
Connectivity Requirements.............................................................. 9
Installation Overview....................................................................... 10
Initial Installation - Quick Reference ........................................... 10
Installing VS-Link Updates - Quick Reference ............................ 10
Adding a Unit to an Existing Installation - Quick Reference...... 11
“Hot-Swapping” Hardware - Quick Reference .............................. 11
Obtaining Software or Document Updates................................. 12
Comtrol Corporate Headquarters.................................................. 12
Comtrol Europe .............................................................................. 12
Technical Support............................................................................. 13
Windows NT
VS-Link Installation and Configuration Overview................... 15
Removing Existing VS-Link Software.......................................... 17
VS-Link Software Installation ....................................................... 19
Extracting the Files........................................................................ 19
Installing a New Version of VS-Link............................................. 20
Verifying the Installation............................................................... 29
Using VS-Link .................................................................................... 30
Accessing VS-Link Menus ............................................................. 31
Changing Configuration Parameters ............................................ 33
Configuring the Backup Server Feature ....................................... 34
Adding Units After the Initial Installation................................... 35
“Hot-Swapping” Units.................................................................... 36
Using Optional VS-Link Features................................................. 37
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
Hardware Installation
Information
Manual PDF
Operating System
Manual
Version
A
Size Driver
54KB
File Name
6631.pdf
Observations
InterChangeVS 2000 V.34 North America
Hardware Installation Card
Product Overview
The InterChangeVS 2000 is an analog multimodem
virtual server that can be stacked or mounted in a rack.
This VS2000 contains eight 33.6K bps modem ports.
VS2000 features include:
• Eight RJ11 modem ports ready to connect to your
phone lines
• Diagnostic LEDs
VS-Link software provides the following features, which
are discussed in the VS2000 VS-Link Installation and
Configuration Guide:
• Backup server
• “Hot-swapping”
• Individual modem reset capability
• Terminal program (WCOM32)
• Port Monitor program (PORTMON)
See the VS2000 VS-Link™ Installation and
Configuration Guide for information about installing
the software for this product and for reference
information for the AT command set.
Installing VS2000 Hardware
Use the following procedure to connect the VS2000.
1. Record the model and serial numbers of the VS2000.
2. Optionally, mount the VS2000 into the rack using
the enclosed mounting brackets. The unit is
designed to install in the rack with the front or back
of the unit facing the front of the rack.
Warning: If mounting the VS2000 into a rack mount
unit, make sure the rack is not top heavy.
3. Connect the cable from the appropriate Ethernet
connection (10Base-T or AUI) on the VS2000 to your
server or Ethernet hub.
Note: If connecting the VS2000 directly to the server, an
Ethernet crossover cable is required.
Safety Notices
Installation of inside wire may bring you close to
electrical wire, conduit, terminals and other electrical
facilities. Extreme caution must be used to avoid
electrical shock from such facilities. Avoid contact with
electrical current by following these guidelines:
• Use tools with insulated handles.
• Do not place telephone wiring or connections in any
conduit, outlet or junction box containing electrical
wiring.
Note: Do not work on your telephone wiring at all if you
wear a pacemaker. Telephone lines carry
electrical current.
• Telephone wiring must be at least 6 feet from bare
power wiring or lightning rods and associated wires,
and at least 6 inches from other wire (antenna
wires, doorbell wires, wires from transformers to
neon signs), steam or hot water pipes, and heating
ducts.
• Before working with existing inside wiring, check all
electrical outlets for a square telephone dial light
transformer and unplug it from the electrical outlet.
Failure to unplug all telephone transformers can
cause electrical shock.
• Do not place a jack where it would allow a person to
use the telephone while in a bathtub, shower,
swimming pool, or similar hazardous location.
• Protectors and grounding wire placed by the service
provider must not be connected to, removed, or
modified by the customer.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS2000 v.34
Description
Device Driver
Operating System
Windows NT 3.51
Version
2.35
Size Driver
372KB
File Name
1800002b.exe
Observations
Do NOT install this driver in Windows 2000/XP operating systems. Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS
Use this file to install the Comtrol software. This readme
file covers:
- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information
VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.
VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.
This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES
This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER
Comtrol recommends removing older versions of the driver
before installing new releases.
1. Open the Control Panel and start the Network applet.
2. Select the Adapters tab.
3. Highlight Comtrol VS1000/VS2000.
4. Click the Remove button.
5. Close the Network applet.
6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER
After you have extracted the driver files, follow these steps:
1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.
2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.
3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.
4. Enter the drive and directory path to the installation files
and click OK
Access to Official Website Comtrol
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.