EnGenius EOC-3610S EXT Download Manual and Firmware

Release Date Jan 31, 2008
Firmware :EOC-3610-1.0.1.04
Changed
• base on firmware 1.1.02
• add checksum on runtime_config.c
• add nv_cash on runtime_config.c

Release Date Oct 30, 2007
Firmware :ECB-3610-1.0.1.02
Features Enhanced
• The firmware v1.0.0.0.2 fixed in connecting 12th, 13th channel issue, but it still
can site survey (12th, 13th) channel. (20070705_1)
• ETSI and FCC Mode can site survey 1~14ch. (20070705_1 #1)
• The default SSID should be changed from "Engenius" to "EnGenius".
(20070712_2 #7)
• In CB info.html, the note "...please close this screen...." should be changed to
"…please close this window to get best performance.". (20070712_2 #8)
• In AP & CB mode, the SuperAG_mode info. should be re-added on the
*info.html because PM has decided to re-enable the mode. (20070712_2 #9)
• When setting the country code with super user/pass, the message should be
changed to "Please set channel information at Wireless web page after device
reboot!". (20070712_2 #11)
• In CB mode, the "info" on line#283 of info2.html is not defined so that the RSSI
cannot be displayed in WPA/WPA2 mode. (20070712_2 #12)
• CB send link down trap continuously in 11b mode, when CB don't associate with
any AP.

Release Date Aug 22, 2007
Firmware :ECB-3610-1.0.1.01
New Features
• SuperG function
• RSSI process bar
Features Enhanced
• When the power interrupte many times, the device setting will reset to default.
(NCB-8610-SQA-PIL-08102007.xls 20070510_01)
• ColdStart should be done in the boot process. (20070712_1 #1)
• WarmStart should be sent when rebooting the device. (20070712_1 #2)
• Two definitions for same type "DisplayString" in AP MIB. (20070712_1 #3)
• In CB mib, the type of "PhysAddress" has two imports. (20070712_1 #4)
• Two definitions for same type "PhysAddress" in AP MIB. (20070712_1 #5)
• In CB mib, the type of "DisplayString" has two imports. (20070712_1 #6)
• In AP mode, the mib of wdsAPMACAddress has no value when it is enabled.
(20070712_1 #7)
• In the AP MIB descrption, the WDS format should be noted as
"ABCDEF123456". (20070712_1 #8)

Release Date Aug 17, 2007
Firmware :ECB-3610-1.0.0.04
Changed
• Disable UART(RS-232) function.

Release Date July 17, 2007
Firmware :1.0.0.03
Features Enhanced
• In the apply?link= web page under CB mode, the Wireless "Bridger" should be
changed to Wireless "Bridge".(20070712_2)
• The Turbo_mode on the *.info.html should be removed because PM has decided
to remove turbo mode in AP mode.(20070712_2)
• In CB mode, the Turbo_mode info should be removed PM has decided to remove
turbo mode in AP mode.(20070712_2)
• The Preferred BSSID has no value in CB mode.(20070712_3)
• In adhoc mode, the Preferred BSSID has no value.(20070712_3)

Release Date July 9, 2007
Firmware :1.0.0.02
New Features
• follow 3610 firmware 1.0.0.01
Features Enhanced
• CB mode FCC card can connect ETSI 11/12 channel.
Changed
• Disable FCC3 function

Indoor Application
ECB-3610S/8610S/8610 Series
1. Place the unit in an appropriate place
after conducting a site survey.
2. Plug one end of the Ethernet cable into
the RJ-45 port of the device and another
end into your PC/Notebook.
3. Insert the DC-inlet of the power adapter
into the port labeled “DC-IN” and the
other end into the power socket on the
wall.
Outdoor Application
EOC-3610S/8610S/8610 Series
1. Place the unit in an appropriate place
after conducting a site survey.
2. Plug one end of the Ethernet cable into
the AP port of the PoE Injector and the
other end into the Bridge/AP.
3. Place one end of another Ethernet cable
into the Network port of the PoE Injector
and another end into your PC/Notebook.
4. Insert the DC-inlet of the power adapter
into the port labeled “DC-IN” and the
other end into the power socket on the
wall.
IP Address Configuration
This device can be configured as a Client
Bridge The default IP address of the device is
192.168.1.1 (CB mode) In order to log into
this device, you must first configure the
TCP/IP settings of your PC/Notebook.
1. In the control panel, double click
Network Connections and then double
click on the connection of your Network
Interface Card (NIC). You will then see
the following screen.
2. Select Internet Protocol (TCP/IP) and
then click on the Properties button. This
will allow you to configure the TCP/IP
settings of your PC/Notebook.
3. Select Use the following IP Address
radio button and then enter the IP
address (192.168.1.21) and subnet
mask (255.255.255.0). Ensure that the
IP address and subnet mask are on the
same subnet as the device.
4. Click on the OK button to close this
window, and once again to close LAN
properties window.
Logging In
1. To configure the Bridge through the
web-browser, enter the IP address of the
Bridge (default: 192.168.1.1) into the
address bar of the web-browser and
press Enter.
2. After connecting to the IP address, the
web-browser will display the login page.
Specify the User Name and Password.
The device does not have a user name
and password configured by default,
leave user name and password field blank
and then click on the Login button.