Emulex DS3000 Download Drivers, Utilities, Manual, Firmware and BIOS

Available 61 files for DS3000
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 x86 BootBIOS
Operating Systems
Boot Code
Version BIOS
2.02a2
Size BIOS
38Kb
File Name
bb202a2.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: Intel (32-bit) The adapter boot BIOS provides x86 boot capability through the use of INT13
system BIOS calls. The adapter Boot BIOS supports:

(1) Multi-topology: Fabric Point to Point; FC-AL: Private loop and Public loop
topologies.
(2) Multi-initiators: The adapter BIOS supports up to 32 Emulex LightPulse
adapters in a system.
(3) Multi-LUNs: The adapter BIOS supports up to 256 LUNs.
(4) Multi-boot: The adapter BIOS complies with the BIOS Boot Specification
(BBS).
(5) EDD (Enhanced Disk Drive Services): The adapter BIOS supports both the
EDD 3.0 and EDD 2.1 specifications depending on the selection in the
adapter BIOS configuration utility.
(6) Boot fail over feature: There are eight boot entries that can be
configured in the adapter BIOS configuration utility. If the first boot
entry fails the system is still able to boot from the second configured
boot entry and so on.
\2.02a2.txt this file you are reading

\DB202a2.PRG Lp8000 adapter boot BIOS version 2.02a2
\CB202a2.PRG Lp9000 adapter boot BIOS version 2.02a2
\HB202a2.PRG Lp9802 adapter boot BIOS version 2.02a2
\TB202a2.PRG Lp10000 adapter boot BIOS version 2.02a2
\BB202a2.PRG Lp11000 adapter boot BIOS version 2.02a2
\QB202a2.PRG Lp850 adapter boot BIOS version 2.02a2
\RB202a2.PRG Lp952 adapter boot BIOS version 2.02a2
\LB202a2.PRG Lp982 adapter boot BIOS version 2.02a2
\MB202a2.PRG Lp1050 adapter boot BIOS version 2.02a2
\JB202a2.PRG Lp1150 adapter boot BIOS version 2.02a2
\EB202a2.PRG Lp101 adapter boot BIOS version 2.02a2
\YB202a2.PRG LPe111 adapter boot BIOS version 2.02a2
\AB202a2.PRG Lp21000 adapter boot BIOS version 2.02a2
\WB202a2.PRG LPe1150 adapter boot BIOS version 2.02a2
\ZB202a2.PRG LPe11000 adapter boot BIOS version 2.02a2
\UB202a2.PRG LPe12000 adapter boot BIOS version 2.02a2
\OB202a2.PRG LPe1250 adapter boot BIOS version 2.02a2
\PB202a2.PRG LPe121 adapter boot BIOS version 2.02a2


***** Important Note ******

(1) BIOS downloading

The adapter boot BIOS image has increased in size to 49K. As a result, it might
fail during the downloading of the BIOS .prg file. One way to correct the
problem is to download the firmware .AWC file WITHOUT the BIOS image
(for example: dd390a7.awc) and then download the adapter boot BIOS .prg file.
(2) BIOS was not activated (Enabled)

If the adapter boot BIOS is not enabled by LP6DUTIL or an Emulex O.S.
configuration utility, the adapter and the drives connected to the adapter
cannot not be configured to be used to boot the system. In addition if there is
a "No BIOS support" message displayed next to this adapter in the adapter BIOS
configuration utility the user must use LP6DUTIL or other Emulex O.S.
configuration utility to enable the adapter boot BIOS in order to allow this adapter
to be used a bootable controller by the host system.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 OpenBoot
Operating Systems
Boot Code
Version Driver
3.10a3
Size Driver
42Kb
File Name
bo310a3.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 4095).
\readme.txt This file you are reading

\SO310a3.PRG Lp7000 Open Firmware 3.10a3
\DO310a3.PRG Lp8000 Open Firmware 3.10a3
\CO310a3.PRG Lp9000 Open Firmware 3.10a3
\HO310a3.PRG Lp9802 Open Firmware 3.10a3
\MO310a3.PRG Lp1050 Open Firmware 3.10a3
\TO310a3.PRG Lp10000 Open Firmware 3.10a3
\BO310a3.PRG Lp11000 Open Firmware 3.10a3
\ZO310a3.PRG Lpe11000 Open Firmware 3.10a3
\UO310a3.PRG LPe12000 Open Firmware 3.10a3
\AO310a3.PRG LP21000 Open Firmware 3.10a3
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.

(1) This procedure assumes there is already a 'local' boot disk.

(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.

(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding ('nailing' a specific scsi id to a specific wwpn or did).

(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.

----------------------------------------------------------------------

----------------------- NEW CHANGES 3.10a3 ------------------------

1. Fixed the issue for the in-correct device id of (LP21000) HBA, and
cause the system fail to initialize the (LP21000) HBA during POST.
(CR75595)
----------------------- NEW CHANGES 3.10a2 ------------------------
1. In some UNIX server, the HBA adapter does not get initialized when DR
is initiated, the cause of the issue is during DR operation, some
Forth word commands from Fcode can't use in HBA's device memory
instead it can only runs under system memory, and that makes the error
message "Segmentation Fault" by the system's Fcode interpreter. This
release fixed the issue by replace different methods for those Forth
word commands to make it compatible with the DR operation. (CR073924)
----------------------- NEW CHANGES 3.10a1 ------------------------

1. Supported multi-Luns from 0 upto 4095, added "set-max-lun" command
to allow user to select the maxmium lun support, the default max lun
is 255. (CR29372)

2. Fixed the issue on fail to update the FC boot target when system
comes up from POST. (CR29373)

3. Fixed the issue for system hangs in scan disk if the link topology
changed after system firmware discovered the bootable lun with
a different topology. (CR29019)

4. Fixed the issue on some system will fail to init the config-port when
option command "set-post-linkup" was enabled. (CR29249)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 EFIBoot
Operating Systems
Boot Code
Version Driver
4.00a1
Size Driver
219Kb
File Name
be400a1.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: Intel Itanium (64-bit) The current EFI (Extensible Firmware Interface) Boot provides 64-bit system
boot capability through the use of the EFI Shell. EFIBoot supports EFI
Specification 1.10 and EFI Source Code version 1.10.14.61 and 1.10.14.62.

EFIBoot supports:

(1) Multi-Topology : Fabric Point-to-Point; FC-AL: Private Loop and Public
Loop.

(2) EFI Protocols : Configuration, Component Name, Firmware Update, VPD,
LunCtrlAttrs and Diagnostics are supported.

(3) Operating System : Windows Server 2003 and Red-Hat Linux

(4) Multi-Device path : Fibre/SCSI device path selectable through the Driver
Configuration Protocol.

(5) Multi-Initiators : Up to 128 adapters in a system.

(6) Multi-Boot : Eight targets/controller selectable through the Driver
configuration Protocol.

(7) Multi-LUNs : Up to 4096 LUNs/target for a volume set device.
Up to 256 LUNs/target for a peripheral device.

(8) Multi-Mode : Peripheral and Volume Set devices are supported.

(9) Multi-Utility : Setup and firmware update are supported.
Files included in this release:

EFI Byte Code Driver Images:

\rel_notes.txt this file you are reading
\HE400A1.PRG Lp9802 EFIBoot version 4.00A1
\LE400A1.PRG Lp982 EFIBoot version 4.00A1
\TE400A1.PRG Lp10000 EFIBoot version 4.00A1
\ME400A1.PRG Lp1050 EFIBoot version 4.00A1
\EE400A1.PRG Lp101 EFIBoot version 4.00A1
\BE400A1.PRG Lp11000 EFIBoot version 4.00A1
\JE400A1.PRG Lp1150 EFIBoot version 4.00A1
\ZE400A1.PRG Lpe11000 EFIBoot version 4.00A1
\WE400A1.PRG Lpe1150 EFIBoot version 4.00A1
\YE400A1.PRG Lpe111 EFIBoot version 4.00A1
\UE400A1.PRG Lpe12000 EFIBoot version 4.00A1
\OE400A1.PRG Lpe1250 EFIBoot version 4.00A1
\ElxCli400A1.efi

***** Important Note ******

(1) EFIBoot was not enabled from loading to system memory:

If the adapter EFIBoot is not enabled from loading to system, this adapter
will not be configured. User must use LP6dutil or some other OS Utility to
enable the EFIBoot in order to make this card bootable.

(2) EFIBoot Bios was enabled to configure the adapter and No Link:

EFIBoot will wait for 15 seconds/adapter to confirm a link.

(3) If two or more adapters have same EFIBoot driver version, EFIBoot will
load only one driver.

(4) If there are adapters with different EFIBoot driver versions, EFIBoot
will load the highest version of the EFIBoot driver.

(5) In order to display Linkup speed, use the latest version of the firmware.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.03a4
Size Driver
303Kb
File Name
bu503a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Contains: x86 BootBIOS 2.02a2, OpenBoot 3.10a3 and EFIBoot 4.00a1 This Universal Boot version 5.03a4 contains:

(1) x86 BootBIOS version 2.02a2
(2) OpenBoot version 3.10a3
(3) EFIBoot version 4.00a1

For detailed information about x86 BootBIOS, please refer to section II below,
for OpenBoot, section III, and for EFIBoot, section IV. This Universal Boot can
boot on either Intel x86 Platform, Non-Intel Fcode, or EFI environment. In other
words, the platform is transparent and the user should not be concerned with any
differences with regard to x86 BootBIOS, OpenBoot, or EFIBoot.

Universal Boot is a complete image, whenever it is enabled by any Emulex OS
utility, the whole image (x86 BootBIOS, OpenBoot and EFIBoot) is enabled. This
is also true for disable.
Files included in this release:

\503a4.txt this file you are reading
\HU503a4.PRG LP9802 Universal Boot
\TU503a4.PRG LP10000 Universal Boot
\BU503a4.PRG LP11000 Universal Boot
\ZU503a4.PRG LPe11000 Universal Boot
\UU503a4.PRG LPe12000 Universal Boot
\AU503a4.PRG LP21000 Universal Boot
\elxcli400a1.efi EFI 4.00a1 Driver
Universal Boot Load Procedure

The Light Pulse Universal Boot is distributed as a .PRG file. This file may be
downloaded to the Adapter using the firmware upgrade procedure with the following
Utility in Various systems.

1. "Drvcfg" : EFI based Systems.

Please refer to section 4 in EFIBoot for user interface how to download
Universal Boot in EFI based systems.

2. LP6DUTIL.EXE : DOS based utility.

Please refer to the LP6DUTIL version 9.0a13, or later, documentation for user
interface how to download EFIBoot in DOS PCI systems.

3. LPUTILNT : Windows Miniport Driver.

Please refer to the utility user manual for details on using the above tool.

4. Emulex Configuration Tool : Windows Port Driver.

Please refer to the elxcfg user manual for details on using the above tool.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Boot Code Update Manual
Operating Systems
Boot Code
Size Manual
4.9Mb
File Name
bootcode.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive. Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 x86 BootBIOS
Operating Systems
Boot Code
Version BIOS
2.02a2
Size BIOS
38Kb
File Name
bb202a2.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: Intel (32-bit) The adapter boot BIOS provides x86 boot capability through the use of INT13
system BIOS calls. The adapter Boot BIOS supports:

(1) Multi-topology: Fabric Point to Point; FC-AL: Private loop and Public loop
topologies.
(2) Multi-initiators: The adapter BIOS supports up to 32 Emulex LightPulse
adapters in a system.
(3) Multi-LUNs: The adapter BIOS supports up to 256 LUNs.
(4) Multi-boot: The adapter BIOS complies with the BIOS Boot Specification
(BBS).
(5) EDD (Enhanced Disk Drive Services): The adapter BIOS supports both the
EDD 3.0 and EDD 2.1 specifications depending on the selection in the
adapter BIOS configuration utility.
(6) Boot fail over feature: There are eight boot entries that can be
configured in the adapter BIOS configuration utility. If the first boot
entry fails the system is still able to boot from the second configured
boot entry and so on.
\2.02a2.txt this file you are reading

\DB202a2.PRG Lp8000 adapter boot BIOS version 2.02a2
\CB202a2.PRG Lp9000 adapter boot BIOS version 2.02a2
\HB202a2.PRG Lp9802 adapter boot BIOS version 2.02a2
\TB202a2.PRG Lp10000 adapter boot BIOS version 2.02a2
\BB202a2.PRG Lp11000 adapter boot BIOS version 2.02a2
\QB202a2.PRG Lp850 adapter boot BIOS version 2.02a2
\RB202a2.PRG Lp952 adapter boot BIOS version 2.02a2
\LB202a2.PRG Lp982 adapter boot BIOS version 2.02a2
\MB202a2.PRG Lp1050 adapter boot BIOS version 2.02a2
\JB202a2.PRG Lp1150 adapter boot BIOS version 2.02a2
\EB202a2.PRG Lp101 adapter boot BIOS version 2.02a2
\YB202a2.PRG LPe111 adapter boot BIOS version 2.02a2
\AB202a2.PRG Lp21000 adapter boot BIOS version 2.02a2
\WB202a2.PRG LPe1150 adapter boot BIOS version 2.02a2
\ZB202a2.PRG LPe11000 adapter boot BIOS version 2.02a2
\UB202a2.PRG LPe12000 adapter boot BIOS version 2.02a2
\OB202a2.PRG LPe1250 adapter boot BIOS version 2.02a2
\PB202a2.PRG LPe121 adapter boot BIOS version 2.02a2


***** Important Note ******

(1) BIOS downloading

The adapter boot BIOS image has increased in size to 49K. As a result, it might
fail during the downloading of the BIOS .prg file. One way to correct the
problem is to download the firmware .AWC file WITHOUT the BIOS image
(for example: dd390a7.awc) and then download the adapter boot BIOS .prg file.
(2) BIOS was not activated (Enabled)

If the adapter boot BIOS is not enabled by LP6DUTIL or an Emulex O.S.
configuration utility, the adapter and the drives connected to the adapter
cannot not be configured to be used to boot the system. In addition if there is
a "No BIOS support" message displayed next to this adapter in the adapter BIOS
configuration utility the user must use LP6DUTIL or other Emulex O.S.
configuration utility to enable the adapter boot BIOS in order to allow this adapter
to be used a bootable controller by the host system.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 OpenBoot
Operating Systems
Boot Code
Version Driver
3.10a3
Size Driver
42Kb
File Name
bo310a3.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 4095).
\readme.txt This file you are reading

\SO310a3.PRG Lp7000 Open Firmware 3.10a3
\DO310a3.PRG Lp8000 Open Firmware 3.10a3
\CO310a3.PRG Lp9000 Open Firmware 3.10a3
\HO310a3.PRG Lp9802 Open Firmware 3.10a3
\MO310a3.PRG Lp1050 Open Firmware 3.10a3
\TO310a3.PRG Lp10000 Open Firmware 3.10a3
\BO310a3.PRG Lp11000 Open Firmware 3.10a3
\ZO310a3.PRG Lpe11000 Open Firmware 3.10a3
\UO310a3.PRG LPe12000 Open Firmware 3.10a3
\AO310a3.PRG LP21000 Open Firmware 3.10a3
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.

(1) This procedure assumes there is already a 'local' boot disk.

(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.

(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding ('nailing' a specific scsi id to a specific wwpn or did).

(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.

----------------------------------------------------------------------

----------------------- NEW CHANGES 3.10a3 ------------------------

1. Fixed the issue for the in-correct device id of (LP21000) HBA, and
cause the system fail to initialize the (LP21000) HBA during POST.
(CR75595)
----------------------- NEW CHANGES 3.10a2 ------------------------
1. In some UNIX server, the HBA adapter does not get initialized when DR
is initiated, the cause of the issue is during DR operation, some
Forth word commands from Fcode can't use in HBA's device memory
instead it can only runs under system memory, and that makes the error
message "Segmentation Fault" by the system's Fcode interpreter. This
release fixed the issue by replace different methods for those Forth
word commands to make it compatible with the DR operation. (CR073924)
----------------------- NEW CHANGES 3.10a1 ------------------------

1. Supported multi-Luns from 0 upto 4095, added "set-max-lun" command
to allow user to select the maxmium lun support, the default max lun
is 255. (CR29372)

2. Fixed the issue on fail to update the FC boot target when system
comes up from POST. (CR29373)

3. Fixed the issue for system hangs in scan disk if the link topology
changed after system firmware discovered the bootable lun with
a different topology. (CR29019)

4. Fixed the issue on some system will fail to init the config-port when
option command "set-post-linkup" was enabled. (CR29249)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 EFIBoot
Operating Systems
Boot Code
Version Driver
4.00a1
Size Driver
219Kb
File Name
be400a1.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Platform: Intel Itanium (64-bit) The current EFI (Extensible Firmware Interface) Boot provides 64-bit system
boot capability through the use of the EFI Shell. EFIBoot supports EFI
Specification 1.10 and EFI Source Code version 1.10.14.61 and 1.10.14.62.

EFIBoot supports:

(1) Multi-Topology : Fabric Point-to-Point; FC-AL: Private Loop and Public
Loop.

(2) EFI Protocols : Configuration, Component Name, Firmware Update, VPD,
LunCtrlAttrs and Diagnostics are supported.

(3) Operating System : Windows Server 2003 and Red-Hat Linux

(4) Multi-Device path : Fibre/SCSI device path selectable through the Driver
Configuration Protocol.

(5) Multi-Initiators : Up to 128 adapters in a system.

(6) Multi-Boot : Eight targets/controller selectable through the Driver
configuration Protocol.

(7) Multi-LUNs : Up to 4096 LUNs/target for a volume set device.
Up to 256 LUNs/target for a peripheral device.

(8) Multi-Mode : Peripheral and Volume Set devices are supported.

(9) Multi-Utility : Setup and firmware update are supported.
Files included in this release:

EFI Byte Code Driver Images:

\rel_notes.txt this file you are reading
\HE400A1.PRG Lp9802 EFIBoot version 4.00A1
\LE400A1.PRG Lp982 EFIBoot version 4.00A1
\TE400A1.PRG Lp10000 EFIBoot version 4.00A1
\ME400A1.PRG Lp1050 EFIBoot version 4.00A1
\EE400A1.PRG Lp101 EFIBoot version 4.00A1
\BE400A1.PRG Lp11000 EFIBoot version 4.00A1
\JE400A1.PRG Lp1150 EFIBoot version 4.00A1
\ZE400A1.PRG Lpe11000 EFIBoot version 4.00A1
\WE400A1.PRG Lpe1150 EFIBoot version 4.00A1
\YE400A1.PRG Lpe111 EFIBoot version 4.00A1
\UE400A1.PRG Lpe12000 EFIBoot version 4.00A1
\OE400A1.PRG Lpe1250 EFIBoot version 4.00A1
\ElxCli400A1.efi

***** Important Note ******

(1) EFIBoot was not enabled from loading to system memory:

If the adapter EFIBoot is not enabled from loading to system, this adapter
will not be configured. User must use LP6dutil or some other OS Utility to
enable the EFIBoot in order to make this card bootable.

(2) EFIBoot Bios was enabled to configure the adapter and No Link:

EFIBoot will wait for 15 seconds/adapter to confirm a link.

(3) If two or more adapters have same EFIBoot driver version, EFIBoot will
load only one driver.

(4) If there are adapters with different EFIBoot driver versions, EFIBoot
will load the highest version of the EFIBoot driver.

(5) In order to display Linkup speed, use the latest version of the firmware.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.03a4
Size Driver
303Kb
File Name
bu503a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Contains: x86 BootBIOS 2.02a2, OpenBoot 3.10a3 and EFIBoot 4.00a1 This Universal Boot version 5.03a4 contains:

(1) x86 BootBIOS version 2.02a2
(2) OpenBoot version 3.10a3
(3) EFIBoot version 4.00a1

For detailed information about x86 BootBIOS, please refer to section II below,
for OpenBoot, section III, and for EFIBoot, section IV. This Universal Boot can
boot on either Intel x86 Platform, Non-Intel Fcode, or EFI environment. In other
words, the platform is transparent and the user should not be concerned with any
differences with regard to x86 BootBIOS, OpenBoot, or EFIBoot.

Universal Boot is a complete image, whenever it is enabled by any Emulex OS
utility, the whole image (x86 BootBIOS, OpenBoot and EFIBoot) is enabled. This
is also true for disable.
Files included in this release:

\503a4.txt this file you are reading
\HU503a4.PRG LP9802 Universal Boot
\TU503a4.PRG LP10000 Universal Boot
\BU503a4.PRG LP11000 Universal Boot
\ZU503a4.PRG LPe11000 Universal Boot
\UU503a4.PRG LPe12000 Universal Boot
\AU503a4.PRG LP21000 Universal Boot
\elxcli400a1.efi EFI 4.00a1 Driver
Universal Boot Load Procedure

The Light Pulse Universal Boot is distributed as a .PRG file. This file may be
downloaded to the Adapter using the firmware upgrade procedure with the following
Utility in Various systems.

1. "Drvcfg" : EFI based Systems.

Please refer to section 4 in EFIBoot for user interface how to download
Universal Boot in EFI based systems.

2. LP6DUTIL.EXE : DOS based utility.

Please refer to the LP6DUTIL version 9.0a13, or later, documentation for user
interface how to download EFIBoot in DOS PCI systems.

3. LPUTILNT : Windows Miniport Driver.

Please refer to the utility user manual for details on using the above tool.

4. Emulex Configuration Tool : Windows Port Driver.

Please refer to the elxcfg user manual for details on using the above tool.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Boot Code Update Manual
Operating Systems
Boot Code
Size Manual
4.9Mb
File Name
bootcode.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive. Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.02a4
Size Driver
206Kb
File Name
zu502a4.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Contains: x86 BootBIOS 2.00a1, OpenBoot 1.50a9 and EFIBoot 3.11a5
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.10a2
Size Driver
352Kb
File Name
zu510a2.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Universal BOOT 5.10a2 is required for uEFI support on IBM x3550 M2 Type 7946 and x3650 M2 Type 7947 Servers. Insure this version is installed on this Host Bus Adapter. This Universal Boot version 5.10a2 contains:

(1) x86 BootBIOS version 2.11a0
(2) OpenBoot version 3.10a3
(3) EFIBoot version 4.11a2

For detailed information about x86 BootBIOS, please refer to section II below,
for OpenBoot, section III, and for EFIBoot, section IV. This Universal Boot can
boot on either Intel x86 Platform, Non-Intel Fcode, or EFI environment. In other
words, the platform is transparent and the user should not be concerned with any
differences with regard to x86 BootBIOS, OpenBoot, or EFIBoot.

Universal Boot is a complete image, whenever it is enabled by any Emulex OS
utility, the whole image (x86 BootBIOS, OpenBoot and EFIBoot) is enabled. This
is also true for disable.
Files included in this release:

\510a2.txt this file you are reading
\HU510a2.PRG LP9802 Universal Boot
\TU510a2.PRG LP10000 Universal Boot
\BU510a2.PRG LP11000 Universal Boot
\ZU510a2.PRG LPe11000 Universal Boot
\UU510a2.PRG LPe12000 Universal Boot
\AU510a2.PRG LP21000 Universal Boot
\elxcli411a2.efi EFI 4.11a2 Driver
Universal Boot Load Procedure

The Light Pulse Universal Boot is distributed as a .PRG file. This file may be
downloaded to the Adapter using the firmware upgrade procedure with the following
Utility in Various systems.

1. "Drvcfg" : EFI based Systems.

Please refer to section 4 in EFIBoot for user interface how to download
Universal Boot in EFI based systems.

2. DosLpCfg.EXE : DOS based utility.

Please refer to the utility user manual for details on using the above tool.

3. LPUTILNT : Windows Miniport Driver.

Please refer to the utility user manual for details on using the above tool.

4. Emulex Configuration Tool : Windows Port Driver.

Please refer to the elxcfg user manual for details on using the above tool.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Boot Code Update Manual
Operating Systems
Boot Code
Size Manual
4.9Mb
File Name
bootcode.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive. Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.02a4
Size Driver
206Kb
File Name
zu502a4.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Contains: x86 BootBIOS 2.00a1, OpenBoot 1.50a9 and EFIBoot 3.11a5
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Universal Boot
Operating Systems
Boot Code
Version Driver
5.10a2
Size Driver
352Kb
File Name
zu510a2.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive.
Universal BOOT 5.10a2 is required for uEFI support on IBM x3550 M2 Type 7946 and x3650 M2 Type 7947 Servers. Insure this version is installed on this Host Bus Adapter. This Universal Boot version 5.10a2 contains:

(1) x86 BootBIOS version 2.11a0
(2) OpenBoot version 3.10a3
(3) EFIBoot version 4.11a2

For detailed information about x86 BootBIOS, please refer to section II below,
for OpenBoot, section III, and for EFIBoot, section IV. This Universal Boot can
boot on either Intel x86 Platform, Non-Intel Fcode, or EFI environment. In other
words, the platform is transparent and the user should not be concerned with any
differences with regard to x86 BootBIOS, OpenBoot, or EFIBoot.

Universal Boot is a complete image, whenever it is enabled by any Emulex OS
utility, the whole image (x86 BootBIOS, OpenBoot and EFIBoot) is enabled. This
is also true for disable.
Files included in this release:

\510a2.txt this file you are reading
\HU510a2.PRG LP9802 Universal Boot
\TU510a2.PRG LP10000 Universal Boot
\BU510a2.PRG LP11000 Universal Boot
\ZU510a2.PRG LPe11000 Universal Boot
\UU510a2.PRG LPe12000 Universal Boot
\AU510a2.PRG LP21000 Universal Boot
\elxcli411a2.efi EFI 4.11a2 Driver
Universal Boot Load Procedure

The Light Pulse Universal Boot is distributed as a .PRG file. This file may be
downloaded to the Adapter using the firmware upgrade procedure with the following
Utility in Various systems.

1. "Drvcfg" : EFI based Systems.

Please refer to section 4 in EFIBoot for user interface how to download
Universal Boot in EFI based systems.

2. DosLpCfg.EXE : DOS based utility.

Please refer to the utility user manual for details on using the above tool.

3. LPUTILNT : Windows Miniport Driver.

Please refer to the utility user manual for details on using the above tool.

4. Emulex Configuration Tool : Windows Port Driver.

Please refer to the elxcfg user manual for details on using the above tool.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Boot Code Update Manual
Operating Systems
Boot Code
Size Manual
4.9Mb
File Name
bootcode.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Boot Code works with the existing BIOS on supported systems and allows the system to boot from a connected Fibre Channel drive. Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Dual Port
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
431Kb
File Name
zf270a5.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Compatibility:

This kit supports the LPe11002 PCI host adapter.

This kit includes the following files:

README.TXT The file you are reading

ZF270A5.ALL All firmware components, no boot code

LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:

----- Changes between 2.70a5 and previous releases ----

With VNP enabled and no registered VNPs, firmware will now function
as if VNPs are not enabled. (CR 23132)

Port number generation for virtual ports has been corrected.
(CR 23051, 23131)

Corrected handling of AHB parity errors. (CR 23049, 23050)

A timeout is prevented by allowing the firmware to process fatal DMA
engine errors even if the DMA is not complete, such as during a PCI
master abort. (CR 22563)

The R_A_TOV field is now properly expressed in milliseconds. (CR 22562)

Any attentions pending during link down are now sent. (CR 22510)

Firmware now seperates BDL DMA requests so that one is stopped before
another is started. (CR 22162, 22179)

QDR memory POST was modified to establish proper ECC and prevent false
memory read errors. (CR 22519, 22520)

Corrected processing of BDL with unexpected offset to properly handle
incoming data frame. (CR 22564)

Incorporated new Emulex SLI-3 protocol. (CR 20834, 20843)

SLI-3 coding inconsistencies were found during in-house test with no
reported instances of failure.
- Proper wakeup parameters have been generated (CR 21597)
- Mailbox response interlock correction (CR 22051)
- READ_REV command had to be corrected (CR 22067, 22114)
- Corrected data abort by assuring all data structures
are initialized to zero before allocation. (CR 22513)

Allow VPD offset to be outside of specification for greater flexibility
with some systems. (CR 21548)

Corrected PCI configuration to advertise VPD access for Zephyr 1.1 ASICs.
(CR 21391)

Protocol testing with invalid conditions revealed protocol response
errors which have had no reported instances of failure in the field.
(CR 17199, 17200, 17203, 20788)

An I/O timeout during tape operation was eliminated by delaying
processing of any FCP2 errors during discovery. (CR 18287)

Improved DMA error handling of split errors where host memory has been
made unavailable. (CR 19348)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Single Port
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
430Kb
File Name
zd270a5.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Offline Utility Version 1.0a6
Operating Systems
Firmware
Version Utilities
2.70a5
Size Utilities
95Kb
File Name
doslpcfg_10a6.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Firmware Update Manual
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
106Kb
File Name
fwupdate.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Dual Port
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
293Kb
File Name
bf280a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Compatibility:

This kit supports the LP11002 and LP1105 PCI-X host adapters.

This kit includes the following files:

README.TXT The file you are reading
BF280A4.ALL All firmware components, no boot code
Changes and Corrections:

-- Changes in version 2.80a4 --

Volatile WWNs now indicate presence in the Host Status Register.
(CR 83090, 83091, 83092)

-- Changes in version 2.80a3 --

Bringing up the loop was made more tolerant and consistent. (CR 82586,
82587)

READ_CONFIG mailbox command no longer returns wrong information on system
running Solaris for x86. (CR 82588)

Changed Receive Timeout default timer value to avoid one-second
shortfall. (CR 82591)

-- Changes in version 2.80a2 --

VPI values are now set to zero after a system reboot. (CR 75272)

Fixed code to correctly process link counter update on link down (cable
pull). (CR 75618, 82314)

Performing a firmware update using HBAnyware 4.0 across platforms no
longer results in the firmware update failing and causing the HBA to
appear offline when seen from a remote HBA while appearing online to
the local system. (CR 82162, 82163)

Revised command queueing method so that transmit buffer actions do not
starve generic sequence operations. (CR 82331, 82332)

Corrected dump table formatting and size issue. (CR 82361, 82362)

-- Changes in version 2.80a1 --

Allow 32-bit firmware counters RxWords, TxWords, RxFrames, and TxFrames
to roll over for continued use by statistical applications. (CR 74512,
74911)

The internal loopback test now works properly. (CR 74539)

PCI-e HBAs use "no soft reset" capability present in PCIPM 1.2 to
preserve values across reset. (CR 75198, 75199, 75200, 75201)

UNREG_LOGIN with RPI=0xFFFF and VPI=0xFFFF now performs an
UNREG_LOGIN_ALL for all virtual N_Ports. (CR 75273)

Correct code is used for VNP FLOGI handling. (CR 75274)

Enhanced SLI-3 UNREG_LOGIN command to check for RPI. (CR 75336)

-- Changes in version 2.80a0 --

Firmware download is now successful on both ports of a dual-port HBA.
(CR 25956, 28844)

The link activity LED no longer continues to blink after link down
following a cable pull. (CR 26947, 28876)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Single Port
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
293Kb
File Name
bd280a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Compatibility:

This kit supports the LP11000 PCI-X host adapter.

This kit includes the following files:

README.TXT The file you are reading
BD280A4.ALL All firmware components, no boot code
Changes and Corrections:

-- Changes in version 2.80a4 --

Volatile WWNs now indicate presence in the Host Status Register.
(CR 83090, 83091, 83092)

-- Changes in version 2.80a3 --

Bringing up the loop was made more tolerant and consistent. (CR 82586,
82587)

READ_CONFIG mailbox command no longer returns wrong information on system
running Solaris for x86. (CR 82588)

Changed Receive Timeout default timer value to avoid one-second
shortfall. (CR 82591)

-- Changes in version 2.80a2 --

VPI values are now set to zero after a system reboot. (CR 75272)

Fixed code to correctly process link counter update on link down (cable
pull). (CR 75618, 82314)

Performing a firmware update using HBAnyware 4.0 across platforms no
longer results in the firmware update failing and causing the HBA to
appear offline when seen from a remote HBA while appearing online to
the local system. (CR 82162, 82163)

Revised command queueing method so that transmit buffer actions do not
starve generic sequence operations. (CR 82331, 82332)

Corrected dump table formatting and size issue. (CR 82361, 82362)

-- Changes in version 2.80a1 --

Allow 32-bit firmware counters RxWords, TxWords, RxFrames, and TxFrames
to roll over for continued use by statistical applications. (CR 74512,
74911)

The internal loopback test now works properly. (CR 74539)

PCI-e HBAs use "no soft reset" capability present in PCIPM 1.2 to
preserve values across reset. (CR 75198, 75199, 75200, 75201)

UNREG_LOGIN with RPI=0xFFFF and VPI=0xFFFF now performs an
UNREG_LOGIN_ALL for all virtual N_Ports. (CR 75273)

Correct code is used for VNP FLOGI handling. (CR 75274)

Enhanced SLI-3 UNREG_LOGIN command to check for RPI. (CR 75336)

-- Changes in version 2.80a0 --

Firmware download is now successful on both ports of a dual-port HBA.
(CR 25956, 28844)

The link activity LED no longer continues to blink after link down
following a cable pull. (CR 26947, 28876)

Firmware now forces a new sequence on BA_ACC. (CR 27411)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Firmware Update Manual
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
106Kb
File Name
fwupdate.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Dual Port
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
293Kb
File Name
bf280a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Compatibility:

This kit supports the LP11002 and LP1105 PCI-X host adapters.

This kit includes the following files:

README.TXT The file you are reading
BF280A4.ALL All firmware components, no boot code
Changes and Corrections:

-- Changes in version 2.80a4 --

Volatile WWNs now indicate presence in the Host Status Register.
(CR 83090, 83091, 83092)

-- Changes in version 2.80a3 --

Bringing up the loop was made more tolerant and consistent. (CR 82586,
82587)

READ_CONFIG mailbox command no longer returns wrong information on system
running Solaris for x86. (CR 82588)

Changed Receive Timeout default timer value to avoid one-second
shortfall. (CR 82591)

-- Changes in version 2.80a2 --

VPI values are now set to zero after a system reboot. (CR 75272)

Fixed code to correctly process link counter update on link down (cable
pull). (CR 75618, 82314)

Performing a firmware update using HBAnyware 4.0 across platforms no
longer results in the firmware update failing and causing the HBA to
appear offline when seen from a remote HBA while appearing online to
the local system. (CR 82162, 82163)

Revised command queueing method so that transmit buffer actions do not
starve generic sequence operations. (CR 82331, 82332)

Corrected dump table formatting and size issue. (CR 82361, 82362)

-- Changes in version 2.80a1 --

Allow 32-bit firmware counters RxWords, TxWords, RxFrames, and TxFrames
to roll over for continued use by statistical applications. (CR 74512,
74911)

The internal loopback test now works properly. (CR 74539)

PCI-e HBAs use "no soft reset" capability present in PCIPM 1.2 to
preserve values across reset. (CR 75198, 75199, 75200, 75201)

UNREG_LOGIN with RPI=0xFFFF and VPI=0xFFFF now performs an
UNREG_LOGIN_ALL for all virtual N_Ports. (CR 75273)

Correct code is used for VNP FLOGI handling. (CR 75274)

Enhanced SLI-3 UNREG_LOGIN command to check for RPI. (CR 75336)

-- Changes in version 2.80a0 --

Firmware download is now successful on both ports of a dual-port HBA.
(CR 25956, 28844)

The link activity LED no longer continues to blink after link down
following a cable pull. (CR 26947, 28876)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Single Port
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
293Kb
File Name
bd280a4.zip
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Compatibility:

This kit supports the LP11000 PCI-X host adapter.

This kit includes the following files:

README.TXT The file you are reading
BD280A4.ALL All firmware components, no boot code
Changes and Corrections:

-- Changes in version 2.80a4 --

Volatile WWNs now indicate presence in the Host Status Register.
(CR 83090, 83091, 83092)

-- Changes in version 2.80a3 --

Bringing up the loop was made more tolerant and consistent. (CR 82586,
82587)

READ_CONFIG mailbox command no longer returns wrong information on system
running Solaris for x86. (CR 82588)

Changed Receive Timeout default timer value to avoid one-second
shortfall. (CR 82591)

-- Changes in version 2.80a2 --

VPI values are now set to zero after a system reboot. (CR 75272)

Fixed code to correctly process link counter update on link down (cable
pull). (CR 75618, 82314)

Performing a firmware update using HBAnyware 4.0 across platforms no
longer results in the firmware update failing and causing the HBA to
appear offline when seen from a remote HBA while appearing online to
the local system. (CR 82162, 82163)

Revised command queueing method so that transmit buffer actions do not
starve generic sequence operations. (CR 82331, 82332)

Corrected dump table formatting and size issue. (CR 82361, 82362)

-- Changes in version 2.80a1 --

Allow 32-bit firmware counters RxWords, TxWords, RxFrames, and TxFrames
to roll over for continued use by statistical applications. (CR 74512,
74911)

The internal loopback test now works properly. (CR 74539)

PCI-e HBAs use "no soft reset" capability present in PCIPM 1.2 to
preserve values across reset. (CR 75198, 75199, 75200, 75201)

UNREG_LOGIN with RPI=0xFFFF and VPI=0xFFFF now performs an
UNREG_LOGIN_ALL for all virtual N_Ports. (CR 75273)

Correct code is used for VNP FLOGI handling. (CR 75274)

Enhanced SLI-3 UNREG_LOGIN command to check for RPI. (CR 75336)

-- Changes in version 2.80a0 --

Firmware download is now successful on both ports of a dual-port HBA.
(CR 25956, 28844)

The link activity LED no longer continues to blink after link down
following a cable pull. (CR 26947, 28876)

Firmware now forces a new sequence on BA_ACC. (CR 27411)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Firmware Update Manual
Operating Systems
Firmware
Version Firmware
2.80a4
Size Firmware
106Kb
File Name
fwupdate.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407)
Note: For the Solaris SFS driver, version 1.11i or 2.11i (or later) must be installed before you update to firmware version 2.80a4. Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Dual Port
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
431Kb
File Name
zf270a5.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Compatibility:

This kit supports the LPe11002 PCI host adapter.

This kit includes the following files:

README.TXT The file you are reading

ZF270A5.ALL All firmware components, no boot code

LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:

----- Changes between 2.70a5 and previous releases ----

With VNP enabled and no registered VNPs, firmware will now function
as if VNPs are not enabled. (CR 23132)

Port number generation for virtual ports has been corrected.
(CR 23051, 23131)

Corrected handling of AHB parity errors. (CR 23049, 23050)

A timeout is prevented by allowing the firmware to process fatal DMA
engine errors even if the DMA is not complete, such as during a PCI
master abort. (CR 22563)

The R_A_TOV field is now properly expressed in milliseconds. (CR 22562)

Any attentions pending during link down are now sent. (CR 22510)

Firmware now seperates BDL DMA requests so that one is stopped before
another is started. (CR 22162, 22179)

QDR memory POST was modified to establish proper ECC and prevent false
memory read errors. (CR 22519, 22520)

Corrected processing of BDL with unexpected offset to properly handle
incoming data frame. (CR 22564)

Incorporated new Emulex SLI-3 protocol. (CR 20834, 20843)

SLI-3 coding inconsistencies were found during in-house test with no
reported instances of failure.
- Proper wakeup parameters have been generated (CR 21597)
- Mailbox response interlock correction (CR 22051)
- READ_REV command had to be corrected (CR 22067, 22114)
- Corrected data abort by assuring all data structures
are initialized to zero before allocation. (CR 22513)

Allow VPD offset to be outside of specification for greater flexibility
with some systems. (CR 21548)

Corrected PCI configuration to advertise VPD access for Zephyr 1.1 ASICs.
(CR 21391)

Protocol testing with invalid conditions revealed protocol response
errors which have had no reported instances of failure in the field.
(CR 17199, 17200, 17203, 20788)

An I/O timeout during tape operation was eliminated by delaying
processing of any FCP2 errors during discovery. (CR 18287)

Improved DMA error handling of split errors where host memory has been
made unavailable. (CR 19348)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Single Port
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
430Kb
File Name
zd270a5.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Offline Utility Version 1.0a6
Operating Systems
Firmware
Version Utilities
2.70a5
Size Utilities
95Kb
File Name
doslpcfg_10a6.zip
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Firmware Update Manual
Operating Systems
Firmware
Version Firmware
2.70a5
Size Firmware
106Kb
File Name
fwupdate.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Installation Manual LPe11000
Operating Systems
Hardware Manuals
Size Manual
786Kb
File Name
lpe11000.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction..................................................................................................................................................1
Major Features...............................................................................................................................1
Compatibility...................................................................................................................................1
Prerequisites...................................................................................................................................1
Setting the Jumpers.....................................................................................................................................2
Installing the Host Bus Adapter....................................................................................................................3
Attaching Media...........................................................................................................................................5
Applying Power............................................................................................................................................7
Viewing the LEDs...........................................................................................................................7
POST Conditions and Results.........................................................................................................7
References..................................................................................................................................................9
Specifications.................................................................................................................................9
FCC and Regulatory Notices.........................................................................................................11
Declaration of Conformity..............................................................................................................12
Laser Safety Notice.......................................................................................................................14

Introduction
This manual describes the Emulex® LPe12000, LPe12002 and LPe12004, 8 gigabit per second (Gb/s)
Fibre Channel (FC) to Peripheral Component Interconnect Express (PCIe) host bus adapters (HBAs).
They feature a revolutionary design with integrated ARM-1156 cores, integrated SERDES, integrated
SRAM, and external Double-Data Rate (DDRII SRAM) memory structure. The LPe12000 is a singlechannel
adapter. The LPe12002 is a dual-channel adapter.The LPe12004 is a four-channel adapter.
The core technology of these HBAs is the ninth generation FC controller by Emulex. The controller
incorporates a multifunction native PCIe core that is compliant to the PCIe Base Specification 2.0 and
PCI Express CEM Specification 2.0. The HBAs support packet transfers up to 5 gigatransfers per
second (5.0 GT/s) on the PCIe link. The supported physical PCIe connector is x4 or x8. The fully
featured FC port is compliant to various American National Standards Institute (ANSI) FC standards.
The product is targeted at FC storage networking environments that require the highest degrees of
robustness, performance and ease of management.

Major Features
• PCIe device with one FC port
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCIe to FC controller with one internal processor
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCIe and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processor with instruction and data cache for each port
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb core for FC and 2.5-Gb cores for PCIe
• Complies with the PCIe base and CEM 1.0a specifications:
•x1 or x4 lane link interface (auto-negotiated with system) at 2.5-Gb/s
•Supports VC0 (1 Virtual Channel) and TC0 (1 Traffic Class)
•Configuration /IO/ Memory read/write, completion and message
•Supports 64-bit addressing
•ECRC for all transmitted PCIe data packets
•Link CRC on all PCIe packets and message
information
•Supports large payload size- 2048 bytes for read/write
•Supports large read request size- 4096 bytes
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LPe11000 HBA provides an embedded short wave optical (LC) connection with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Installation Manual LPe11002
Operating Systems
Hardware Manuals
Size Manual
804Kb
File Name
lpe11002.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction..................................................................................................................................................1
Major Features...............................................................................................................................1
Compatibility...................................................................................................................................2
Prerequisites...................................................................................................................................2
Setting the Jumpers.....................................................................................................................................2
Installing the Host Bus Adapter....................................................................................................................3
Attaching Media...........................................................................................................................................5
Applying Power............................................................................................................................................6
Viewing the LEDs...........................................................................................................................6
POST Conditions and Results.........................................................................................................6
References..................................................................................................................................................8
Specifications.................................................................................................................................8
FCC and Regulatory Notices...........................................................................................................9
Declaration of Conformity..............................................................................................................10
Laser Safety Notice.......................................................................................................................12

Introduction
The Emulex® LPe11002 host bus adapter (HBA) is a dual-channel, 4.25 gigabit per second (Gb/s), Fibre
Channel (FC) Peripheral Component Interconnect Express (PCIe) HBA. The core technology of this
HBA is Emulex’s eighth generation FC controller. The controller incorporates a multifunction native PCIe
core that is compliant to the PCIe Base Specification 1.0a and PCI Express CEM Specification 1.0a. The
HBA supports packet transfers up to 2048 bytes on the PCIe link with support for x1 or x4 lane
negotiation. The supported physical PCIe connector is x4 or higher (x8 or x16). The two independent,
fully featured FC ports are compliant to various American National Standards Institute (ANSI) FC
standards. The product is targeted at FC storage networking environments that require the highest
degrees of robustness, performance and ease of management.

Major Features
• Multifunction PCIe device with two fully independent FC ports
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCIe to FC controller with two internal processors
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCIe and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processors with instruction and data cache for each port
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb cores for FC and 2.5-Gb cores for PCIe
• Complies with the PCIe base and CEM 1.0a specifications:
•x1 or x4 lane link interface (auto-negotiated with system) at 2.5-Gb/s
•Supports VC0 (1 Virtual Channel) and TC0 (1 Traffic Class)
•Configuration /IO/ Memory read/write, completion and message
•Supports 64-bit addressing
•ECRC for all transmitted PCIe data packets
•Link CRC on all PCIe packets and message
information
•Supports large payload size- 2048 bytes for read/write
•Supports large read request size- 4096 bytes
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LPe11002 HBA provides two embedded short wave optical (LC) connections with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware (per port):
•Up to 510 FC port logins
•Up to 1023 concurrent exchanges
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11002-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Installation Manual LPe11000
Operating Systems
Hardware Manuals
Size Manual
786Kb
File Name
lpe11000.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction..................................................................................................................................................1
Major Features...............................................................................................................................1
Compatibility...................................................................................................................................1
Prerequisites...................................................................................................................................1
Setting the Jumpers.....................................................................................................................................2
Installing the Host Bus Adapter....................................................................................................................3
Attaching Media...........................................................................................................................................5
Applying Power............................................................................................................................................7
Viewing the LEDs...........................................................................................................................7
POST Conditions and Results.........................................................................................................7
References..................................................................................................................................................9
Specifications.................................................................................................................................9
FCC and Regulatory Notices.........................................................................................................11
Declaration of Conformity..............................................................................................................12
Laser Safety Notice.......................................................................................................................14

Introduction
This manual describes the Emulex® LPe12000, LPe12002 and LPe12004, 8 gigabit per second (Gb/s)
Fibre Channel (FC) to Peripheral Component Interconnect Express (PCIe) host bus adapters (HBAs).
They feature a revolutionary design with integrated ARM-1156 cores, integrated SERDES, integrated
SRAM, and external Double-Data Rate (DDRII SRAM) memory structure. The LPe12000 is a singlechannel
adapter. The LPe12002 is a dual-channel adapter.The LPe12004 is a four-channel adapter.
The core technology of these HBAs is the ninth generation FC controller by Emulex. The controller
incorporates a multifunction native PCIe core that is compliant to the PCIe Base Specification 2.0 and
PCI Express CEM Specification 2.0. The HBAs support packet transfers up to 5 gigatransfers per
second (5.0 GT/s) on the PCIe link. The supported physical PCIe connector is x4 or x8. The fully
featured FC port is compliant to various American National Standards Institute (ANSI) FC standards.
The product is targeted at FC storage networking environments that require the highest degrees of
robustness, performance and ease of management.

Major Features
• PCIe device with one FC port
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCIe to FC controller with one internal processor
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCIe and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processor with instruction and data cache for each port
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb core for FC and 2.5-Gb cores for PCIe
• Complies with the PCIe base and CEM 1.0a specifications:
•x1 or x4 lane link interface (auto-negotiated with system) at 2.5-Gb/s
•Supports VC0 (1 Virtual Channel) and TC0 (1 Traffic Class)
•Configuration /IO/ Memory read/write, completion and message
•Supports 64-bit addressing
•ECRC for all transmitted PCIe data packets
•Link CRC on all PCIe packets and message
information
•Supports large payload size- 2048 bytes for read/write
•Supports large read request size- 4096 bytes
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LPe11000 HBA provides an embedded short wave optical (LC) connection with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Installation Manual LPe11002
Operating Systems
Hardware Manuals
Size Manual
804Kb
File Name
lpe11002.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Introduction..................................................................................................................................................1
Major Features...............................................................................................................................1
Compatibility...................................................................................................................................2
Prerequisites...................................................................................................................................2
Setting the Jumpers.....................................................................................................................................2
Installing the Host Bus Adapter....................................................................................................................3
Attaching Media...........................................................................................................................................5
Applying Power............................................................................................................................................6
Viewing the LEDs...........................................................................................................................6
POST Conditions and Results.........................................................................................................6
References..................................................................................................................................................8
Specifications.................................................................................................................................8
FCC and Regulatory Notices...........................................................................................................9
Declaration of Conformity..............................................................................................................10
Laser Safety Notice.......................................................................................................................12

Introduction
The Emulex® LPe11002 host bus adapter (HBA) is a dual-channel, 4.25 gigabit per second (Gb/s), Fibre
Channel (FC) Peripheral Component Interconnect Express (PCIe) HBA. The core technology of this
HBA is Emulex’s eighth generation FC controller. The controller incorporates a multifunction native PCIe
core that is compliant to the PCIe Base Specification 1.0a and PCI Express CEM Specification 1.0a. The
HBA supports packet transfers up to 2048 bytes on the PCIe link with support for x1 or x4 lane
negotiation. The supported physical PCIe connector is x4 or higher (x8 or x16). The two independent,
fully featured FC ports are compliant to various American National Standards Institute (ANSI) FC
standards. The product is targeted at FC storage networking environments that require the highest
degrees of robustness, performance and ease of management.

Major Features
• Multifunction PCIe device with two fully independent FC ports
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCIe to FC controller with two internal processors
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCIe and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processors with instruction and data cache for each port
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb cores for FC and 2.5-Gb cores for PCIe
• Complies with the PCIe base and CEM 1.0a specifications:
•x1 or x4 lane link interface (auto-negotiated with system) at 2.5-Gb/s
•Supports VC0 (1 Virtual Channel) and TC0 (1 Traffic Class)
•Configuration /IO/ Memory read/write, completion and message
•Supports 64-bit addressing
•ECRC for all transmitted PCIe data packets
•Link CRC on all PCIe packets and message
information
•Supports large payload size- 2048 bytes for read/write
•Supports large read request size- 4096 bytes
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LPe11002 HBA provides two embedded short wave optical (LC) connections with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware (per port):
•Up to 510 FC port logins
•Up to 1023 concurrent exchanges
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LPe11000-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LPe11000/LPe11002 HBAs
Emulex 4GB FC Single-Port PCI-E HBA (IBM P/N 42C2069)
Emulex 4GB FC Dual-Port PCI-E HBA (IBM P/N 42C2071) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Installation Manual LP11000
Operating Systems
Hardware Manuals
Size Manual
309Kb
File Name
install_lp11000.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Introduction .................................................................................................................................................1
Major Features ...............................................................................................................................1
Compatibility ..................................................................................................................................2
Prerequisites ..................................................................................................................................2
Setting the Jumpers ....................................................................................................................................3
Installing the Host Bus Adapter ...................................................................................................................4
Attaching Media ..........................................................................................................................................5
Applying Power ...........................................................................................................................................6
Viewing the LEDs ...........................................................................................................................6
POST Conditions and Results ........................................................................................................6
References .................................................................................................................................................7
Specifications ................................................................................................................................7
FCC and Regulatory Notices ..........................................................................................................8
Declaration of Conformity ...............................................................................................................9
Laser Safety Notice ......................................................................................................................11

Introduction
The Emulex® LP11000 host bus adapter (HBA) is a single-channel, 4-gigabit per second (Gb/s), Fibre
Channel (FC) PCI-X 2.0 HBA. The core technology of this HBA is Emulex’s seventh generation FC
controller. The controller incorporates a multi-function native PCI-X 2.0 core that is compliant to the
Peripheral Component Interconnect (PCI) and PCI-X local bus specifications. The HBA supports burst
data transfers up to 266-megahertz (MHz) PCI-X Mode 2, 133 MHz PCI-X Mode 1, or 66 MHz PCI. The
fully featured FC port is compliant to various American National Standards Institute (ANSI) FC standards.
The product is targeted at FC storage networking environments that require the highest degrees of
robustness, performance and ease of management.
Major Features
• Multi-function PCI-X device with one FC port
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCI-X 2.0 FC controller with one internal processor
• Complies with the PCI-X 2.0a and PCI 3.0 specifications for 3.3-V add-in cards
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCI-X and FC functionality is contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processor with instruction and data cache
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb core
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LP11000 HBA provides an embedded short wave optical (LC) connection with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802 and LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware:
•Up to 510 FC port logins
•Up to 2047 concurrent exchanges
•I/O multiplexing down to the FC frame level
• Data buffers are capable of supporting 64+ buffer-to-buffer (BB) credits for short-wave
applications
• Link management and recovery are handled by the firmware
• On-board diagnostic capability is accessible via optional connection
• Parts and construction are compliant to the European Union Directive of Restriction of
Hazardous Substances (RoHS)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Installation Manual LP11002
Operating Systems
Hardware Manuals
Size Manual
322Kb
File Name
install_lp11002.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Introduction .................................................................................................................................................1
Major Features ...............................................................................................................................1
Compatibility ..................................................................................................................................2
Prerequisites ..................................................................................................................................2
Setting the Jumpers ....................................................................................................................................3
Installing the Host Bus Adapter ...................................................................................................................4
Attaching Media ..........................................................................................................................................5
Applying Power ...........................................................................................................................................6
Viewing the LEDs ...........................................................................................................................6
POST Conditions and Results ........................................................................................................6
References .................................................................................................................................................7
Specifications ................................................................................................................................7
FCC and Regulatory Notices ..........................................................................................................8
Declaration of Conformity ...............................................................................................................9
Laser Safety Notice ......................................................................................................................11

Introduction
The Emulex® LP11002 host bus adapter (HBA) is a dual-channel, 4-gigabit per second (Gb/s), Fibre
Channel (FC) PCI-X 2.0 HBA. The core technology of this HBA is Emulex’s seventh generation FC
controller. The controller incorporates a multi-function native PCI-X 2.0 core that is compliant to the
Peripheral Component Interconnect (PCI) and PCI-X local bus specifications. The HBA supports burst
data transfers up to 266-megahertz MHz PCI-X Mode 2, 133 MHz PCI-X Mode 1, or 66 MHz PCI. The
two independent, fully featured FC ports are compliant to various American National Standards Institute
(ANSI) FC standards. The product is targeted at FC storage networking environments that require the
highest degrees of robustness, performance and ease of management.
Major Features
• Multi-function PCI-X device with two fully independent FC ports
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCI-X 2.0 to FC controller with two internal processors
• Complies with the PCI-X 2.0a and PCI 3.0 specifications for 3.3-V add-in cards
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCI-X and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processors with instruction and data cache
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb cores
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LP11002 HBA provides an embedded short wave optical (LC) connections with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware (per port):
•Up to 510 FC port logins
•Up to 1023 concurrent exchanges
•I/O multiplexing down to the FC frame level
• Data buffers capable of supporting 16 buffer-to-buffer (BB) credits for short-wave applications
• Link management and recovery handled by the firmware
• On-board diagnostic capability accessible via optional connection
• Parts and construction compliant to the European Union Directive of Restriction of Hazardous
Substances (RoHS)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11002-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Installation Manual LP11000
Operating Systems
Hardware Manuals
Size Manual
309Kb
File Name
install_lp11000.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Introduction .................................................................................................................................................1
Major Features ...............................................................................................................................1
Compatibility ..................................................................................................................................2
Prerequisites ..................................................................................................................................2
Setting the Jumpers ....................................................................................................................................3
Installing the Host Bus Adapter ...................................................................................................................4
Attaching Media ..........................................................................................................................................5
Applying Power ...........................................................................................................................................6
Viewing the LEDs ...........................................................................................................................6
POST Conditions and Results ........................................................................................................6
References .................................................................................................................................................7
Specifications ................................................................................................................................7
FCC and Regulatory Notices ..........................................................................................................8
Declaration of Conformity ...............................................................................................................9
Laser Safety Notice ......................................................................................................................11

Introduction
The Emulex® LP11000 host bus adapter (HBA) is a single-channel, 4-gigabit per second (Gb/s), Fibre
Channel (FC) PCI-X 2.0 HBA. The core technology of this HBA is Emulex’s seventh generation FC
controller. The controller incorporates a multi-function native PCI-X 2.0 core that is compliant to the
Peripheral Component Interconnect (PCI) and PCI-X local bus specifications. The HBA supports burst
data transfers up to 266-megahertz (MHz) PCI-X Mode 2, 133 MHz PCI-X Mode 1, or 66 MHz PCI. The
fully featured FC port is compliant to various American National Standards Institute (ANSI) FC standards.
The product is targeted at FC storage networking environments that require the highest degrees of
robustness, performance and ease of management.
Major Features
• Multi-function PCI-X device with one FC port
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCI-X 2.0 FC controller with one internal processor
• Complies with the PCI-X 2.0a and PCI 3.0 specifications for 3.3-V add-in cards
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCI-X and FC functionality is contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processor with instruction and data cache
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb core
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LP11000 HBA provides an embedded short wave optical (LC) connection with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802 and LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware:
•Up to 510 FC port logins
•Up to 2047 concurrent exchanges
•I/O multiplexing down to the FC frame level
• Data buffers are capable of supporting 64+ buffer-to-buffer (BB) credits for short-wave
applications
• Link management and recovery are handled by the firmware
• On-board diagnostic capability is accessible via optional connection
• Parts and construction are compliant to the European Union Directive of Restriction of
Hazardous Substances (RoHS)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Installation Manual LP11002
Operating Systems
Hardware Manuals
Size Manual
322Kb
File Name
install_lp11002.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Introduction .................................................................................................................................................1
Major Features ...............................................................................................................................1
Compatibility ..................................................................................................................................2
Prerequisites ..................................................................................................................................2
Setting the Jumpers ....................................................................................................................................3
Installing the Host Bus Adapter ...................................................................................................................4
Attaching Media ..........................................................................................................................................5
Applying Power ...........................................................................................................................................6
Viewing the LEDs ...........................................................................................................................6
POST Conditions and Results ........................................................................................................6
References .................................................................................................................................................7
Specifications ................................................................................................................................7
FCC and Regulatory Notices ..........................................................................................................8
Declaration of Conformity ...............................................................................................................9
Laser Safety Notice ......................................................................................................................11

Introduction
The Emulex® LP11002 host bus adapter (HBA) is a dual-channel, 4-gigabit per second (Gb/s), Fibre
Channel (FC) PCI-X 2.0 HBA. The core technology of this HBA is Emulex’s seventh generation FC
controller. The controller incorporates a multi-function native PCI-X 2.0 core that is compliant to the
Peripheral Component Interconnect (PCI) and PCI-X local bus specifications. The HBA supports burst
data transfers up to 266-megahertz MHz PCI-X Mode 2, 133 MHz PCI-X Mode 1, or 66 MHz PCI. The
two independent, fully featured FC ports are compliant to various American National Standards Institute
(ANSI) FC standards. The product is targeted at FC storage networking environments that require the
highest degrees of robustness, performance and ease of management.
Major Features
• Multi-function PCI-X device with two fully independent FC ports
• Auto-negotiation between 1-Gb, 2-Gb or 4-Gb link attachments
• High performance FC HBA with the PCI-X 2.0 to FC controller with two internal processors
• Complies with the PCI-X 2.0a and PCI 3.0 specifications for 3.3-V add-in cards
• Full support for all FC topologies including point-to-point, arbitrated loop and fabric
• Full support for FC service class 2 and 3
• Maximum FC throughput achieved via full duplex hardware support
• End-to-end data path-parity and cyclical redundancy check (CRC) protection, including internal
data path random-access memory (RAM)
• Architectural support for multiple upper layer protocols
• State-of-the-art circuitry:
•All PCI-X and FC functionality contained within a single, custom, high-density, fully integrated FC controller
•Internal ARM 1136J-S processors with instruction and data cache
•Internal serializer deserializer (SerDes) 1-Gb/2-Gb/4-Gb cores
• Internal high-speed static RAM (SRAM)
• Error correcting code (ECC) protection of local memory, including single-bit correction and
double-bit protection
• The LP11002 HBA provides an embedded short wave optical (LC) connections with link
diagnostics capability.
• Host interface via Emulex standard drivers or through custom drivers written to the Emulex
Service Level Interface (SLI-2) that is compatible with the many existing Emulex drivers for
products such as LP8000, LP9002L, LP9802, LP10000 HBAs
• Comprehensive array of operating system (OS) drivers:
•Emulex standard and OEM derivatives of device drivers for Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX
•OEM-specific drivers for AIX and some other operating systems
•Some drivers support both SCSI and IP protocols
•Support for remote and fabric boot functionality
• On-board context management by the firmware (per port):
•Up to 510 FC port logins
•Up to 1023 concurrent exchanges
•I/O multiplexing down to the FC frame level
• Data buffers capable of supporting 16 buffer-to-buffer (BB) credits for short-wave applications
• Link management and recovery handled by the firmware
• On-board diagnostic capability accessible via optional connection
• Parts and construction compliant to the European Union Directive of Restriction of Hazardous
Substances (RoHS)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
LP11000-M4 Troubleshooting Manual
Operating Systems
Hardware Manuals
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
IBM Branded LP11000 / LP11002 HBAs
Emulex 4GB FC Single-Port PCI-X HBA (IBM P/N 42D0405)
Emulex 4GB FC Dual-Port PCI-X HBA (IBM P/N 42D0407) Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
Linux 2.4 Kernel
Version Driver
7.3.6
Size Driver
300Kb
File Name
lpfc_2.4_driver_kit-7.3.6-2.tar.gz
Information
7.3.6 RHEL3 u8 (Linux CD), u7, u6, SLES8 SP4
SUSE Linux Enterprise Server 8 Service Pack 4 or higher
Red Hat Enterprise Linux 3 Updates 6 or higher
Base driver, application helper module and install script (306 KB gz file)

1. System Requirements
2. Description of Install Process
2.1 Driver Installation
2.2 Driver Uninstallation
3. Release Notes

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex LPFC
driver:

Red Hat Enterprise Linux 3 Update 6 and higher
SuSE Linux Enterprise Server 8 with Service Pack 3 and 4

The Emulex LPFC driver and LPFC DFC driver RPMs require gcc compiler
tools and the kernel sources for the running kernel be installed on
the system in order for the driver installation to succeed.
2. Description of Install Process

The lpfc-install script installs both the LPFC driver and the LPFC
DFC driver RPMs. These RPMs install their driver sources to the
/usr/src/lpfc directory, build their drivers for the currently
running kernel, and then install the drivers to the proper
directory for the currently running kernel.

Once the RPMs are installed, the lpfc-install script creates a new
ramdisk for the currently running kernel so that the LPFC driver
is loaded when the kernel is initialized during system startup.

Please refer to the LPFC Linux 7.3 documentation on the Emulex
website at http://www.emulex.com for an installation manual that
includes a complete set of options for the lpfc-install program.

Emulex strongly recommends uninstalling any old LPFC driver kits
before installing the new driver kit. Please refer to the "Driver
Uninstallation" section to uninstall previous versions of the
Emulex LPFC 7.x or older driver.
2.1 Driver Installation

Log in as the user 'root' to a terminal, change to the directory in
which the Emulex LPFC 7.3 driver kit is installed, and execute the
'lpfc-install' script with no options to install the driver:

./lpfc-install

Once the 'lpfc-install' script has completed successfully, the
Emulex LPFC and LPFC DFC drivers will be loaded, and fibre channel
disks that are properly connected to the system should be
accessible. However, a reboot of the system is recommended to load
the LPFC driver through the ramdisk.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Applications Kit
Operating Systems
Linux 2.4 Kernel
Version Driver
7.3.6
Size Driver
175.7Mb
File Name
elxlinuxapps-2.1a29-7.3.6-1-5.tar
Information
7.3.6 RHEL3 u8 (Linux CD), u7, u6, SLES8 SP4
SUSE Linux Enterprise Server 8 Service Pack 4 or higher
Red Hat Enterprise Linux 3 Updates 6 or higher
Remote Management Utility HBAnyware version 2.1a29 and Diagnostic Utility (lputil) version 2.0a12 (185 MB tar file)

HBAnyware 2.1a29 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a29
SSC version 2.1a29
DFC Library version 1.2.1-1
Lputil version 2.0a12
HBAAPI version 2.0.f

Dependencies:

lpfc driver version 7.3.6 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Linux User Manual
Operating Systems
Linux 2.4 Kernel
Version Manual
7.3.6
Size Manual
6Mb
File Name
set.pdf
Information
7.3.6 RHEL3 u8 (Linux CD), u7, u6, SLES8 SP4
SUSE Linux Enterprise Server 8 Service Pack 4 or higher
Red Hat Enterprise Linux 3 Updates 6 or higher
Installation, Configuration and Troubleshooting (3,451 KB pdf file)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.1.6.8
Size Driver
177Kb
File Name
lpfc_2.6_driver_kit-8.1.6.8-2.tar.gz
Information
8.1.6.8 SLES10
SUSE Linux Enterprise Server 10 distribution.
Base driver and install script (214 KB gz file)

1. System Requirements
1.1 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 Loading order of LPFC driver in initial ramdisk
3.1.1 Background
3.1.2 Observed Problem
3.1.3 Workaround
3.2 PCI Hot Plug Support for applications
3.2.1 Observed problem
3.2.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

SuSE Linux Enterprise Server 10

1.1 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the LPFC driver build to succeed. For
example, a system with the 2.6.16.11-7-ppc64 kernel would need the
kernel-source-2.6.16.11-7 package.
2. Description of Install Procedure

The lpfc-install script installs the LPFC driver RPM. This RPM
installs the driver sources to the /usr/src/lpfc directory, builds
the driver for the currently running kernel, and then installs the
driver to the proper directory for the currently running kernel.

Once the RPM is installed, the lpfc-install script creates a new
ramdisk for the currently running kernel so that the 'lpfc' driver
is loaded when the kernel is initialized during system startup.
3. Known Issues

3.1 Loading order of LPFC driver in initial ramdisk

3.1.1 Background

In SLES10, the modules to be loaded as part of the initial ramdisk are
specified through the variable INITRD_MODULES in /etc/sysconfig/kernel. The
modules are loaded in exactly the order in which they appear in
INITRD_MODULES. This is important when starting the system via the initial
ramdisk and accessing the root file system.

The LPFC driver installation adds the "lpfc" driver in the INITRD_MODULES
list of modules at the end of the list, if the "lpfc" list entry is not
already there. If it is already present it will not make any updates.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Applications Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.1.6.8
Size Driver
165.8Mb
File Name
elxlinuxapps-3.2a7-8.1.6.8-2-1.tar
Information
8.1.6.8 SLES10
SUSE Linux Enterprise Server 10 distribution.
HBAnyware utility 3.2a7, lputil 2.0a14, Application helper module 2.1.1 (170 MB tar file)

HBAnyware 3.2a7 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.2a7
SSC version 3.2a7
DFC Library version 80.162-9
Lputil version 2.0a14
HBAAPI version 2.1.e
DFC helper module

Dependencies:

lpfc driver version 8.1.6.8 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

HBAnyware requires the kernel development environment as described here:

This kit installs the Emulex Application Helper Module for the
currently running kernel. Since this installation procedure builds
the module for the currently running kernel, the kernel development
environment must be installed. For systems running Red Hat Enterprise
Linux (RHEL) 4, the appropriate kernel-devel package is required; for
example, a system with the 2.6.9-22.EL kernel would need the
kernel-devel-2.6.9-22.EL package, and a system with the 2.6.9-22.ELsmp
kernel would need the kernel-smp-devel-2.6.9-22.EL package. For
systems running SuSE Linux Enterprise Server (SLES) 9, the appropriate
kernel-source package is required; for example, a system with the
2.6.5-7.139-bigsmp kernel would need the kernel-source-2.6.5-7.139
package.
A log of each installation and uninstallation is recorded in the
following file:

/usr/src/lpfcdfc/utils-install.log
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.1.6.8
Size Manual
2.9Mb
File Name
manual_81.pdf
Information
8.1.6.8 SLES10
SUSE Linux Enterprise Server 10 distribution.
Manual Installation, Configuration and Troubleshooting (2.92 MB) Installation...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 2
Known Issues.................................................................................................... 2
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 4
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex HBA ................................... 6
Installing the Application Helper Module and Utilities .............................................. 7
Prerequisites ............................................................................................... 7
Procedure ................................................................................................... 7
Utilities Directory Structure.......................................................................... 8
Installing the HBAnyware Security Configurator ................................................ 9
Prerequisites ............................................................................................... 9
Procedure ................................................................................................... 9
Installing HBAnyware, lputil and the Application Helper Module using the
Upgrade Kernel Option...................................................................................... 9
Prerequisites ............................................................................................... 9
Procedure ................................................................................................... 9
Uninstalling the Driver Kit ................................................................................ 10
Uninstalling a Previous Application Helper Module
(Stand Alone Kit) ............................................................................................. 11
Uninstalling the Utilities ......................................................................................... 12
Uninstalling the HBAnyware Security Configurator.......................................... 12
Uninstalling HBAnyware, lputil and the Application Helper Module ................. 12
Configuration ........................................................................................13
Introduction............................................................................................................ 13
Starting the HBAnyware Utility for Linux .......................................................... 14
Changing Management Mode ......................................................................... 15
The HBAnyware Utility Window Element Definitions ....................................... 16
The Menu Bar ........................................................................................... 16
The Toolbar ............................................................................................... 16
The Toolbar Buttons .................................................................................. 17
The Discovery-Tree................................................................................... 17
Property Tabs............................................................................................ 18
Status Bar ................................................................................................. 18
Using the the HBAnyware Utility Command-Line Interface.............................. 18
Using the CLI Client .................................................................................. 19
The CLI Client Command Reference ........................................................ 20
Starting the lputil Utility .................................................................................... 34
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.1.10.9
Size Driver
190Kb
File Name
lpfc_2.6_driver_kit-8.1.10.9-2.tar.gz
Information
Support Resources for PRIMEQUEST Servers
RHEL 5 GA (2.6.18-8.el5)
Base driver and install script (189 KB gz file)

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 5

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the -devel package
which matches the kernel package with the same version as the
currently running kernel must be installed for the LPFC driver
build to succeed. For example, a system with the 2.6.18-7 kernel
would need the kernel-devel-2.6.18-7 package.
2. Description of Install Procedure

The lpfc-install script installs the LPFC driver RPM. This RPM
installs the driver sources to the /usr/src/lpfc directory, builds
the driver for the currently running kernel, and then installs the
driver to the proper directory for the currently running kernel.

Once the RPM is installed, the lpfc-install script creates a new
ramdisk for the currently running kernel so that the 'lpfc' driver
is loaded when the kernel is initialized during system startup.
3. Known Issues

3.1 PCI Hot Plug Support for applications

3.1.1 Observed problem

PCI Hot Plug has been found to cause applications (HBAnyware utilities or
third party applications) that use the Emulex libraries (i.e. HBAAPI), to
misbehave or malfunction.

3.1.2 Workaround

A user should stop all applications that are accessing LPFC's HBAAPI
interface (HBAnyware utilities or third party applications) before
performing PCI Hot Plug of an LPFC HBA.

Use the following command to stop the HBAnyware application:
#/usr/sbin/hbanyware/stop_hbanyware

After performing PCI Hot Plug of the HBA you can restart the applications.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Applications Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.1.10.9
Size Driver
207.1Mb
File Name
elxlinuxapps-3.2a14-8.1.10.9-2-1.tar
Information
8.1.10.9 RHEL5, 5.1 (Linux CD) SLES10 SP1
Red Hat Enterprise Linux 5, 5.1
SUSE Linux Enterprise Server 10 SP1
HBAnyware utility 3.2a14, lputil 2.0a14 (207 MB tar file)

HBAnyware 3.2a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.2a14
SSC version 3.2a14
DFC Library version 2-15-1005
Lputil version 2.0a14
HBAAPI version 2.1.e

Dependencies:

HBAnyware requires that the lpfc driver module be installed.
The lpfc driver version 8.1.10.9 and all 8.1.10.x based driver releases are
supported with this version of HBAnyware.
This support includes the RHEL5 and SLES10-SP1 in-distro 8.1.10.3 lpfc driver.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.1.10.9
Size Manual
2.9Mb
File Name
manual_81.pdf
Information
8.1.10.9 RHEL5, 5.1 (Linux CD) SLES10 SP1
Red Hat Enterprise Linux 5, 5.1
SUSE Linux Enterprise Server 10 SP1
Manual Installation, Configuration and Troubleshooting (2.92 MB) Installation...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 2
Known Issues.................................................................................................... 2
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 4
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex HBA ................................... 6
Installing the Application Helper Module and Utilities .............................................. 7
Prerequisites ............................................................................................... 7
Procedure ................................................................................................... 7
Utilities Directory Structure.......................................................................... 8
Installing the HBAnyware Security Configurator ................................................ 9
Prerequisites ............................................................................................... 9
Procedure ................................................................................................... 9
Installing HBAnyware, lputil and the Application Helper Module using the
Upgrade Kernel Option...................................................................................... 9
Prerequisites ............................................................................................... 9
Procedure ................................................................................................... 9
Uninstalling the Driver Kit ................................................................................ 10
Uninstalling a Previous Application Helper Module
(Stand Alone Kit) ............................................................................................. 11
Uninstalling the Utilities ......................................................................................... 12
Uninstalling the HBAnyware Security Configurator.......................................... 12
Uninstalling HBAnyware, lputil and the Application Helper Module ................. 12
Configuration ........................................................................................13
Introduction............................................................................................................ 13
Starting the HBAnyware Utility for Linux .......................................................... 14
Changing Management Mode ......................................................................... 15
The HBAnyware Utility Window Element Definitions ....................................... 16
The Menu Bar ........................................................................................... 16
The Toolbar ............................................................................................... 16
The Toolbar Buttons .................................................................................. 17
The Discovery-Tree................................................................................... 17
Property Tabs............................................................................................ 18
Status Bar ................................................................................................. 18
Using the the HBAnyware Utility Command-Line Interface.............................. 18
Using the CLI Client .................................................................................. 19
The CLI Client Command Reference ........................................................ 20
Starting the lputil Utility .................................................................................... 34
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.2.0.27
Size Driver
214Kb
File Name
lpfc_2.6_driver_kit-8.0.16.27-1.tar.gz
Information
8.0.16.27 RHEL4 u5, u4 (Linux CD), u3, u2, SLES9 SP3, SP2
SUSE Linux Enterprise Server 9 Service Pack 2 or higher
Red Hat Enterprise Linux 4 Update 2 or higher
Base driver, application helper module and install script

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Informational
3.1 Packaging Change Involving The Application Helper Module
3.1.1 Background
3.1.2 Observed Behavior
4. Known Issues
4.1 Uninstalling the Driver Kit on Boot-from-SAN Configurations
4.1.1 Observed problem
4.1.2 Resolution
4.2 Machine Check Exception
4.2.1 Observed problem
4.2.2 Workaround
4.3 Loading order of LPFC driver in initial ramdisk
4.3.1 Background
4.3.2 Observed Problem
4.3.3 Workaround
4.4 System panic while unloading the lpfc module
4.4.1 Background
4.4.2 Observed Problem
4.4.3 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 4 (Update 3 or higher)
SuSE Linux Enterprise Server 9 (SP2 or higher)

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the kernel development
package with the same version as the currently running kernel must
be installed for the LPFC 8.0 driver build to succeed. For
example, a system with the 2.6.9-22.EL kernel would need the
kernel-devel-2.6.9-22.EL package, and a system with the
2.6.9-22.ELsmp kernel would need the kernel-smp-devel-2.6.9-22.EL
package.

1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the LPFC 8.0 driver build to succeed. For
example, a system with the 2.6.5-7.139-bigsmp kernel would need the
kernel-source-2.6.5-7.139 package.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Applications Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.2.0.27
Size Driver
187.5Mb
File Name
elxlinuxapps-3.0a14-8.0.16.27-1-8.tar
Information
8.0.16.27 RHEL4 u5, u4 (Linux CD), u3, u2, SLES9 SP3, SP2
SUSE Linux Enterprise Server 9 Service Pack 2 or higher
Red Hat Enterprise Linux 4 Update 2 or higher
HBAnyware utility 3.0a14, lputil 2.0a13, Application helper module 2.0.15

HBAnyware 3.0a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.0a14
SSC version 3.0a14
DFC Library version 80.163.7
Lputil version 2.0a13
HBAAPI version 2.1.c
DFC helper module

Dependencies:

lpfc driver version 8.0.16.27 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

HBAnyware requires the kernel development environment as described here:

This kit installs the Emulex Application Helper Module for the
currently running kernel. Since this installation procedure builds
the module for the currently running kernel, the kernel development
environment must be installed. For systems running Red Hat Enterprise
Linux (RHEL) 4, the appropriate kernel-devel package is required; for
example, a system with the 2.6.9-22.EL kernel would need the
kernel-devel-2.6.9-22.EL package, and a system with the 2.6.9-22.ELsmp
kernel would need the kernel-smp-devel-2.6.9-22.EL package. For
systems running SuSE Linux Enterprise Server (SLES) 9, the appropriate
kernel-source package is required; for example, a system with the
2.6.5-7.139-bigsmp kernel would need the kernel-source-2.6.5-7.139
package.
A log of each installation and uninstallation is recorded in the
following file:

/usr/src/lpfcdfc/utils-install.log
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.2.0.27
Size Manual
3Mb
File Name
manual.pdf
Information
8.0.16.27 RHEL4 u5, u4 (Linux CD), u3, u2, SLES9 SP3, SP2
SUSE Linux Enterprise Server 9 Service Pack 2 or higher
Red Hat Enterprise Linux 4 Update 2 or higher
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
NetWare 5.1, 6.0 and 6.5
Version Driver
2.21d
Size Driver
65Kb
File Name
nw221d.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.21d August 10, 2006
This Readme file contains the description of the 2.21d version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 5 (NW65SP5)
- NetWare 6.0 with Support Pack 5 (NW6SP5 )
- NetWare 5.1 with Support Pack 8 (NW51SP8)
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LPe111 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Manual
Operating Systems
NetWare 5.1, 6.0 and 6.5
Version Manual
2.21d
Size Manual
484Kb
File Name
manual.pdf
Information
Certification: Novell "YES" Tested and Approved
Installation, Configuration and Troubleshooting (351 KB) Installation ........................................................................................................................................... 1
Driver Information .......................................................................................................... 1
Supported Features................................................................................................. 1
Prerequisites ........................................................................................................... 1
Compatibility ............................................................................................................ 1
Things to Know Before You Download..................................................................... 1
Known Issues .......................................................................................................... 2
Installing the Driver ........................................................................................................ 3
Installing the Driver on a New NetWare Server........................................................ 3
Installing the Driver on an Existing NetWare Server ................................................ 4
The following items are required to install the driver on an existing NetWare
server: ............................................................................................................... 4
Using an Emulex HBA to Boot NetWare 6.5 .................................................................. 6
Shutting Down, Resetting and Restarting the Server............................................... 7
Updating x86 BootBIOS Using the Dos Offline Utility .............................................. 7
The following items are required to load x86 BootBIOS: ................................... 8
Configuration ................................................................................................................................... 10
Driver Parameters ................................................................................................. 10
Special Command Line Parameters ...................................................................... 14
Troubleshooting ................................................................................................................................ 17
Failback Detection Not Automatic.......................................................................... 17
Targets are Not Discovered ................................................................................... 17

Installation
Driver Information
Supported Features
• Supports 16 host bus adapters (HBAs).
• Supports a maximum of 250 targets.
• Supports suitable target hardware. (The Emulex lpfc.ham driver complies with the American
National Standards Institute [ANSI]-T11 Storage Area Network [SAN] protocols for switched
fabrics and arbitrated loops.)
Prerequisites
• NetWare 6.5 - driver tested using Support Pack 5 (NW65SP7).
• NetWare 6.0 - driver tested using Support Pack 5 (NW6SP5).
• NetWare 5.1 - driver tested using Support Pack 8 (NW51SP8).
Compatibility
• The Emulex driver for NetWare is compatible with the following Fibre Channel (FC) host bus
adapters (HBAs):
• LPe11000, LPe11002 and LPe1150 (minimum firmware version 2.50a2)
• LP11000, LP11002, and LP1150 (minimum firmware version 2.10a5)
• LP10000, LP10000DC, LP1050 and LP1050DC (minimum firmware version 2.50a2)
• LP10000ExDC, LPe1050Ex and LP1005DC (minimum firmware version 1.90a4)
• LP9802, LP9802DC, and LP982 (minimum firmware version 1.01a2).
• If you update the firmware on an LP9802DC HBA, use the DOS offline utility version
1.06a or later.
• LP9402DC, LP9002L, LP9002DC and LP952L (recommended firmware version 3.90a7).
Things to Know Before You Download
• Before you download, create a temporary directory for the driver kit.
• You can install NetWare files on an FC disk, provided a local boot disk with DOS exists.
• For NetWare 6.5, you can replace the "local boot drive" with an FC boot drive.
• If you are using NetWare 6.5 SP1 and booting from an Emulex HBA, ensure that the HBA boot
drive is connected to the first HBA loaded. See “Using an Emulex HBA to Boot NetWare 6.5” on
page 6 for more information.
• You may see "orphaned" mirror partitions under NW6SP2. NW6SP3 and the MM6UP1A patch
correct this.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Driver Kit
Operating Systems
Windows 2003
Version Driver
1.30a9
Size Driver
24.2Mb
File Name
storportminiportkit_1-30a9-1i.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note The KB916048 update to the Microsoft Storport driver is required.
Base driver, HBAnyware utility 3.1a8 and lputilnt version 1.8a19 (24 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Quick Install
Operating Systems
Windows 2003
Version Driver
1.30a9
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note The KB916048 update to the Microsoft Storport driver is required
Installing the driver using AutoPilot Installer (498 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex DS3000
Description
Manual
Operating Systems
Windows 2003
Version Manual
1.30a9
Size Manual
4.6Mb
File Name
manual.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
HelpDrivers Since March 2000