Emulex LP101-H Download Drivers, Manual, Firmware and BIOS

Available 29 files for LP101-H
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
x86 BootBIOS
Operating Systems
Boot Code
Version BIOS
1.70a3
Size BIOS
39Kb
File Name
eb170a3.zip
Information
Platform: Intel (32-bit) The current BIOS provides x86 boot capability through the use of INT13 system
BIOS calls. The BIOS supports:

(1) Multi-topology: Fabric Point to Point; FC-AL: Private loop and Public loop
(2) Multi-initiators: Up to 64 adapters in a system
(3) Multi-LUNs: Up to 256 LUNs
(4) Multi-boot: Complies with the BIOS Boot Specification (BBS).
(5) EDD (Enhanced Disk Drive Services): Supports both EDD 3.0 and EDD 2.1
depending on the selection in the BIOS Utility.
(6) Boot fail over feature: There are eight boot entries that can be configured.
If the first boot entry fails the system is still able to boot from the
second configured boot entry and so on.

\readme.txt this file you are reading

\SB170a3.PRG Lp7000 BIOS version 1.70a3
\DB170a3.PRG Lp8000 BIOS version 1.70a3
\CB170a3.PRG Lp9000 BIOS version 1.70a3
\HB170a3.PRG Lp9802 BIOS version 1.70a3
\TB170a3.PRG Lp10000 BIOS version 1.70a3

\QB170a3.PRG Lp850 BIOS version 1.70a3
\RB170a3.PRG Lp950 BIOS version 1.70a3
\LB170a3.PRG Lp982 BIOS version 1.70a3
\MB170a3.PRG Lp1050 BIOS version 1.70a3
\EB170a3.PRG Lp101 BIOS version 1.70a3

***** Important Note ******

(1) BIOS downloading

This version of BIOS image has increased size from 44K to 48K. As a result, it might
fail during the downloading of the BIOS .prg file. One way to correct the problem
is to download the firmware .AWC file WITHOUT the BIOS image
(for example: dd390a7.awc). Then, download the BIOS .prg file.

(2) BIOS was not activated (Enabled)

If the adapter BIOS is not activated (enabled) by LP6dutil or other O.S. utility,
this adapter would not be configured. Also, there is "No BIOS support" message next
to this adapter in the BIOS Utility. User must use LP6dutil or other O.S. Utility
to activate (enabled) the BIOS in order to make this card bootable.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Firmware
Operating Systems
Firmware
Version Firmware
1.91a5
Size Firmware
330Kb
File Name
em191a5.zip
Information
Compatibility:

This kit supports the LP101 PCI host adapter.

This kit includes the following files:

README.TXT The file you are reading

EM191A5.ALL All firmware components, no boot code

LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:

-- Changes and corrections between 1.91a5 and 1.91a4:

Ensure proper DMA behavior upon channel reset. (CR 19091, 19096)

Pre-initialize configuration region to avoid errors if host reads it
before the initial configuration is complete. (CR 19177, 19187, 19188)

-- Changes and corrections between 1.91a4 and 1.91a3:

Several issues with FLASH access during reset of only one port have been
eliminated by synchronizing the flash access speed of both ports.
(CR 17472, 17475, 17539, 17542, 17625, 17626, 17647, 17648, 18212,
18213, 18307)

An exceptionally rigorous test produced a timeout where the rings other
than ring 0 were ignored. The firmware has been corrected to check all
four rings. (CR 15952, 16262, 16279, 16280, 16281, 16282, 16283)

Improved handling of queued data from tape. Recovery of CRC errors
no longer indirectly trigger an abort on slow PCI environments.
(CR 17410, 17510, 17520, 17608, 17610, 17633, 17634, 17635, 18280,
18343)

Changed handling of dropped FCP-2 tape data frames. Upon detecting a
missing frame, the firmware now automatically requests a retransmission
from the drive. (CR 14851, 15184, 16975, 18329)

The firmware now correctly handles intentional IOCB starvation.
(CR 16818, 16873, 16972, 17211)

An I/O timeout during tape operation was eliminated by delaying
processing of any FCP2 errors during discovery. (CR 17363, 18287, 18288)

Improved handling of linked FCP commands in order to avoid timeouts.
(CR 15602, 16114)

Implemented a workaround to avoid a hardware DMA overrun condition.
(CR 17780, 17834, 17908)

To avoid buffer deadlocks, the HBA now completes any existing DMA for
an exchange prior to allocating more free buffers. (CR 16862, 16874,
16973, 18347)

Dump command now correctly dumps memory above 1MB. (CR 18374)

Improved buffer handling logic during error conditions to avoid aborted
exchanges. (CR 17701, 18291, 18292, 18349)

Improved handling of erroneously-sized ECHO responses. (CR 18330,
18332, 18333)

The HBA now transmits all outstanding ACKs before processing any
previously blocked data. (CR 16354, 18334, 18335)

The transmit queue is now restarted after ACK handling to avoid a
transmit hang in Class 2. (CR 18362, 18363, 18364)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.0.16.40
Size Driver
227Kb
File Name
lpfc_2.6_driver_kit-8.0.16.40-2.tar.gz
Information
SUSE Linux Enterprise Server 9 Service Pack 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Red Hat Enterprise Linux 4 Update 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Oracle Enterprise Linux 4 Update 4 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)Asianux 2.0 SP2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
Base driver and install script

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Informational
3.1 Packaging Change Involving The Application Helper Module
3.1.1 Background
3.1.2 Observed Behavior
4. Known Issues
4.1 Uninstalling the Driver Kit on Boot-from-SAN Configurations
4.1.1 Observed problem
4.1.2 Resolution
4.2 Machine Check Exception
4.2.1 Observed problem
4.2.2 Workaround
4.3 Loading order of LPFC driver in initial ramdisk
4.3.1 Background
4.3.2 Observed Problem
4.3.3 Workaround
4.4 System panic while unloading the lpfc module
4.4.1 Background
4.4.2 Observed Problem
4.4.3 Resolution
4.5 PCI Hot Plug Support for applications
4.5.1 Observed problem
4.5.2 Workaround
4.6 Storage Array discovery issues in direct-attach configurations
4.6.1 Observed problem
4.6.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 4 (Update 3 or higher)
SuSE Linux Enterprise Server 9 (SP2 or higher)

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the kernel development
package with the same version as the currently running kernel must
be installed for the LPFC 8.0 driver build to succeed. For
example, a system with the 2.6.9-22.EL kernel would need the
kernel-devel-2.6.9-22.EL package, and a system with the
2.6.9-22.ELsmp kernel would need the kernel-smp-devel-2.6.9-22.EL
package.

1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the LPFC 8.0 driver build to succeed. For
example, a system with the 2.6.5-7.139-bigsmp kernel would need the
kernel-source-2.6.5-7.139 package.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Applications Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.0.16.40
Size Driver
196.4Mb
File Name
elxlinuxapps-3.4a14-8.0.16.40-2-1.tar
Information
SUSE Linux Enterprise Server 9 Service Pack 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Red Hat Enterprise Linux 4 Update 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Oracle Enterprise Linux 4 Update 4 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)Asianux 2.0 SP2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware utility 3.4a14, Application helper module 2.0.30

HBAnyware 3.4a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.4a14
SSC version 3.4a14
DFC Library version 80.164-8
Lputil version
HBAAPI version 2.1.g

Dependencies:

lpfc driver version 8.0.16.40 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Linux User Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.0.16.40
Size Manual
1.1Mb
File Name
manual.pdf
Information
SUSE Linux Enterprise Server 9 Service Pack 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Red Hat Enterprise Linux 4 Update 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Oracle Enterprise Linux 4 Update 4 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)Asianux 2.0 SP2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
Driver for Linux User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
HBAnyware Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.0.16.40
Size Manual
3.5Mb
File Name
hbanyware.pdf
Information
SUSE Linux Enterprise Server 9 Service Pack 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Red Hat Enterprise Linux 4 Update 2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) Oracle Enterprise Linux 4 Update 4 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)Asianux 2.0 SP2 or later (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware Utility User Manual

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.2.0.29
Size Driver
285Kb
File Name
lpfc_2.6_driver_kit-8.2.0.29-1.tar.gz
Information
Red Hat Enterprise Linux 5.0 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) SUSE Linux Enterprise Server 10 SP1 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) Oracle Enterprise Linux 5 or later (x86 and x64 architectures)
Base driver and install script (288 KB gz file)

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround
3.2 Deletion of Vports/PCI Hot Unplug
3.2.1 Observed Problem
3.2.2 Background
3.3 lspci utility displays "Unknown Device" for LPe12000 HBAs
3.3.1 Observed Problem
3.3.2 Background
3.4 Speed of LPe12000 HBA (8Gb) is incorrectly displayed by HBAnyware
3.4.1 Observed Problem
3.4.2 Background
3.5 Port disabled on system boot or HBA reset with authentication enabled
3.5.1 Observed Problem
3.5.2 Workaround
3.6 LILO Boot Loader is not supported - i386 and x86_64 architectures
3.6.1 Observed Problem
3.6.2 Background
3.7 Order of lpfc module in initrd module list
3.7.1 Observed Problem
3.7.2 Workaround
3.8 Devloss timeout after swapping ports
3.8.1 Observed Problem
3.8.2 Workaround
3.9 Suspend to disk and Resume support
3.9.1 Observed Problem
3.9.2 Background
3.10 Deleting vports while devices are in use
3.10.1 Observed Problem
3.10.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 5
SuSE Linux Enterprise Server 10 (SP1 or higher)

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the -devel package
which matches the kernel package with the same version as the
currently running kernel must be installed for the LPFC driver
build to succeed. For example, a system with the 2.6.18-7 kernel
would need the kernel-devel-2.6.18-7 package.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Applications Kit
Operating Systems
Linux 2.6 Kernel
Version Driver
8.2.0.29
Size Driver
179.1Mb
File Name
elxlinuxapps-4.0a31-8.2.0.29-1-1.tar
Information
Red Hat Enterprise Linux 5.0 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) SUSE Linux Enterprise Server 10 SP1 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) Oracle Enterprise Linux 5 or later (x86 and x64 architectures)
HBAnyware utility 4.0a31 (179 MB tar file)

HBAnyware 4.0a31 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.0a31
SSC version 4.0a31
DFC Library version 3.0.25-1-1
HBAAPI version 2.1.g
Multipulse version 3.0.30-1
FCAUTHD version 1.17-1-1
Dependencies:

lpfc driver version 8.2.0.29 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Linux User Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.2.0.29
Size Manual
1.6Mb
File Name
manual.pdf
Information
Red Hat Enterprise Linux 5.0 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) SUSE Linux Enterprise Server 10 SP1 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) Oracle Enterprise Linux 5 or later (x86 and x64 architectures)
Driver for Linux User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
HBAnyware User Manual
Operating Systems
Linux 2.6 Kernel
Version Manual
8.2.0.29
Size Manual
5.3Mb
File Name
hbanyware.pdf
Information
Red Hat Enterprise Linux 5.0 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) SUSE Linux Enterprise Server 10 SP1 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) Oracle Enterprise Linux 5 or later (x86 and x64 architectures)
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
NetWare 5.1-6.0
Version Driver
2.20e
Size Driver
59Kb
File Name
nw220e.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.20e September 30, 2005
This Readme file contains the description of the 2.20e version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 3 (NW65SP3)
- NetWare 6.0 with Support Pack 5 (NW6SP5 )
- NetWare 5.1 with Support Pack 7 (NW51SP7)
- untested with Netware 5.0 with Support Pack 6a (SP6a).
Netware 5.0 is supported by Novell, however no future work is planned for this version.
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Manual
Operating Systems
NetWare 5.1-6.0
Version Manual
2.20e
Size Manual
429Kb
File Name
manual.pdf
Information
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Solaris 8-9-10 SPARC
Version Driver
6.30g
Size Driver
25.5Mb
File Name
solaris-4.0a37-6.30g-1b.tar
Information
SPARC Solaris 8, 9 and 10 (32-bit and 64-bit)
Note This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Base driver, HBAnyware utility 4.0a37, emlxdrv utility 1.00m; emlxdrv is needed for a fresh installation of Solaris 10 Update 1

HBAnyware 4.0a37 Solaris Installation Instructions

Dependencies:

lpfc driver 6.30g or later
hbaapi 2.0.f
Java Runtime Environment

Version 1.5 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

The JRE and instructions for installation can be found at http://java.com.

JAVA NOTE:
HBAnyware needs the Java runtime binaries and libraries, so their path needs to be included
in the PATH environment variable. For example, if your java runtime binaries are in /usr/java/bin,
then include this path in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware and hbacmd currently will not run under Solaris 6. The HBAnyware and hbacmd target OS versions
include Solaris 5.8, 5.9, and 5.10.

HBAnyware is dependent on the Emulex lpfc driver being installed. Please ensure that this package is
installed prior to installing HBAnyware.

HBAnyware Installation Instructions
-----------------------------------
1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Run the unpack script : ./unpack_apps
to obtain correct package version
3. Unzip the file: gunzip HBAnyware-4.0a37-sparc.tar.gz
4. Untar the file: tar -xvf HBAnyware-4.0a37-sparc.tar
5. Run the pkgadd utility: pkgadd -d .
6. When prompted by pkgadd, choose to install HBAnyware
7. When prompted by pkgadd, answer the HBAnyware installation option questions
Running the HBAnyware GUI
-------------------------
1. su to root
2. Execute the command: /opt/HBAnyware/hbanyware
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Manual
Operating Systems
Solaris 8-9-10 SPARC
Version Manual
6.30g
Size Manual
1.6Mb
File Name
manual.pdf
Information
Note This driver is posted as is, with no new version planned.
This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
LPFC Driver for Solaris User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
HBAnyware User Manual
Operating Systems
Solaris 8-9-10 SPARC
Version Manual
6.30g
Size Manual
5.3Mb
File Name
hbanyware.pdf
Information
SPARC Solaris 8, 9 and 10 (32-bit and 64-bit)
Note This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
FCA Utilities Manual
Operating Systems
Solaris 8-9-10 SPARC
Version Manual
6.30g
Size Manual
876Kb
File Name
sfs_utilities.pdf
Information
SPARC Solaris 8, 9 and 10 (32-bit and 64-bit)
Note This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Instructions for using the FCA utilities
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.30a2
Size Driver
14.2Mb
File Name
fcportkit_2-30a2c-3f.exe
Information
Port Driver - IA32
Microsoft WHQL qualified for Windows 2000 Server and 32-bit Windows Server 2003
Base driver and Emulex Configuration Utility (elxcfg) version 1.41a16 (12,927 KB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.30a2
Size Driver
90Kb
File Name
quick_installation.pdf
Information
Port Driver - IA32
Microsoft WHQL qualified for Windows 2000 Server and 32-bit Windows Server 2003
Quick Install Installing the driver using AutoPilot Installer (90 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.30a2
Size Manual
1.4Mb
File Name
manual.pdf
Information
Port Driver - IA32
Microsoft WHQL qualified for Windows 2000 Server and 32-bit Windows Server 2003
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
5.30a2
Size Driver
18.4Mb
File Name
scsiportminiportkit_5-30a2-1d.exe
Information
SCSI Port Driver - IA32
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Windows Server 2003 Upgrade Notice: If you are currently running the Emulex SCSIport Miniport driver version 5.10a10 or earlier, follow these Upgrade Instructions before upgrading from Windows 2000 Server to Windows Server 2003.
Base driver, HBAnyware utility 3.0a9 and lputilnt 1.8a18 (18 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
SMI-S Provider Kit
Operating Systems
Windows 2000-2003
Version Driver
5.30a2
Size Driver
6.9Mb
File Name
elxsmiprovider1.0.12-1.exe
Information
SCSI Port Driver - IA32
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Windows Server 2003 Upgrade Notice: If you are currently running the Emulex SCSIport Miniport driver version 5.10a10 or earlier, follow these Upgrade Instructions before upgrading from Windows 2000 Server to Windows Server 2003.
SMI-S HBA Provider, compliant with the SMI-S 1.0.2 specification and certified against the SNIA-CTP v1.0.2.23 suite
Pre-packaged with OpenPegasus CIMOM v2.3.2, as a turnkey SMI-S agent for ease of installation and deployment (6.97 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
5.30a2
Size Driver
115Kb
File Name
quick_installation.pdf
Information
SCSI Port Driver - IA32
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Windows Server 2003 Upgrade Notice: If you are currently running the Emulex SCSIport Miniport driver version 5.10a10 or earlier, follow these Upgrade Instructions before upgrading from Windows 2000 Server to Windows Server 2003.
Installing the driver using AutoPilot Installer (468 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
5.30a2
Size Manual
4.3Mb
File Name
manual.pdf
Information
SCSI Port Driver - IA32
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Windows Server 2003 Upgrade Notice: If you are currently running the Emulex SCSIport Miniport driver version 5.10a10 or earlier, follow these Upgrade Instructions before upgrading from Windows 2000 Server to Windows Server 2003.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Driver Kit
Operating Systems
Windows 2003-2008
Version Driver
2.10a7
Size Driver
11.6Mb
File Name
storportminiportkit_2-10a7-1e.exe
Information
Storport Miniport Driver
Qualification: Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by both Windows Sever 2003 and Windows Server 2008.
Note For Windows Server 2003, SP2 and the KB932755 update to the Microsoft Storport driver are required. KB945119 is recommended. The Storport KB update must be applied before the Emulex Storport Miniport driver can be installed.
Base driver, HBAnyware utility 4.0a32 (11.6 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Quick Installation Manual
Operating Systems
Windows 2003-2008
Version Manual
2.10a7
Size Manual
256Kb
File Name
quick_installation.pdf
Information
Storport Miniport Driver
Qualification: Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by both Windows Sever 2003 and Windows Server 2008.
Note For Windows Server 2003, SP2 and the KB932755 update to the Microsoft Storport driver are required. KB945119 is recommended. The Storport KB update must be applied before the Emulex Storport Miniport driver can be installed.
AutoPilot Installer for Windows Server 2003 and Windows Server 2008

Introduction
AutoPilot Installer® for Emulex® drivers provides installation options that range from a simple installation
with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.
Note: Complete driver and utilities documentation may be downloaded from the Emulex Web site
(www.emulex.com). Click Support at the top of the Web page and navigate by clicking the appropriate
links.
Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.
Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
Distribution Executable File Procedure
To run the distribution executable file:
1. Download the distribution executable file from the Emulex Web site to your system.
2. Double-click the distribution executable file. A window is displayed with driver version
information and Emulex contact information
3. Click Next to access the Location window or click Cancel to close the window.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
User Manual
Operating Systems
Windows 2003-2008
Version Manual
2.10a7
Size Manual
1.2Mb
File Name
manual.pdf
Information
Storport Miniport Driver
Qualification: Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by both Windows Sever 2003 and Windows Server 2008.
Note For Windows Server 2003, SP2 and the KB932755 update to the Microsoft Storport driver are required. KB945119 is recommended. The Storport KB update must be applied before the Emulex Storport Miniport driver can be installed.
Storport Miniport Driver Version 2.10 for Windows Server 2003 and Windows Server 2008

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
HBAnyware User Manual
Operating Systems
Windows 2003-2008
Version Manual
2.10a7
Size Manual
5.3Mb
File Name
hbanyware.pdf
Information
Storport Miniport Driver
Qualification: Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by both Windows Sever 2003 and Windows Server 2008.
Note For Windows Server 2003, SP2 and the KB932755 update to the Microsoft Storport driver are required. KB945119 is recommended. The Storport KB update must be applied before the Emulex Storport Miniport driver can be installed.
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Windows Kit
Operating Systems
Windows Kit
Version Driver
1.30a1
Size Driver
8.4Mb
File Name
elxsmbdriverskit_1.30a1.exe
Information
x86 and x64 Storport Miniport 1.20a3
AutoPilot Manager 2.0a3
AutoPilot Installer 3.1.7
Note: A problem with the auto persistent binding service can cause a system crash when updating to a new version of the Storport Miniport driver. To avoid this problem, stop the auto persistent binding service (Emulex AutoPB) using Administrative Tools and Component Services before installing a new Storport Miniport driver.
Windows Kit1.30a1 (8.7 MB .exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP101-H
Description
Windows Kit
Operating Systems
Windows Kit
Version Driver
1.10a0
Size Driver
5Mb
File Name
elxlp101driverskit_1.10a0.exe
Information
x86 SCSIport Minport 5.20a9
AutoPilot Manager 1.2a5
ApInstall 3.1.7
HelpDrivers Since March 2000