Emulex LP9002C Download Drivers, Utilities, Manual and Firmware

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA
Platform: SPARC, PowerPC This version of Open Boot supports FC-AL: Private loop and Public
loop, and Fabric Point to Point. Also, it supports multi-initiators
and multi-LUNs (0 through 4095).
\readme.txt This file you are reading

\SO310a3.PRG Lp7000 Open Firmware 3.10a3
\DO310a3.PRG Lp8000 Open Firmware 3.10a3
\CO310a3.PRG Lp9000 Open Firmware 3.10a3
\HO310a3.PRG Lp9802 Open Firmware 3.10a3
\MO310a3.PRG Lp1050 Open Firmware 3.10a3
\TO310a3.PRG Lp10000 Open Firmware 3.10a3
\BO310a3.PRG Lp11000 Open Firmware 3.10a3
\ZO310a3.PRG Lpe11000 Open Firmware 3.10a3
\UO310a3.PRG LPe12000 Open Firmware 3.10a3
\AO310a3.PRG LP21000 Open Firmware 3.10a3
--------------- NOTES and CAUTIONS ---------------------
** Ensure that critical files on local boot disk are backed up
as a measure of protection.

(1) This procedure assumes there is already a 'local' boot disk.

(2) The size of the intended (target) fibre channel disk should
be big enough to hold all the file systems, and swap slice
of the local current boot disk.

(3) As there will probably be more than one logical disk drive on
the fibre channel adapter it will be necessary to use persistent
binding ('nailing' a specific scsi id to a specific wwpn or did).

(4) It will be necessary to correlate the intended boot disk displayed
by the 'probe-scsi-all' command to the devices displayed by the
operating system.

----------------------------------------------------------------------

----------------------- NEW CHANGES 3.10a3 ------------------------

1. Fixed the issue for the in-correct device id of (LP21000) HBA, and
cause the system fail to initialize the (LP21000) HBA during POST.
(CR75595)
----------------------- NEW CHANGES 3.10a2 ------------------------
1. In some UNIX server, the HBA adapter does not get initialized when DR
is initiated, the cause of the issue is during DR operation, some
Forth word commands from Fcode can't use in HBA's device memory
instead it can only runs under system memory, and that makes the error
message "Segmentation Fault" by the system's Fcode interpreter. This
release fixed the issue by replace different methods for those Forth
word commands to make it compatible with the DR operation. (CR073924)
----------------------- NEW CHANGES 3.10a1 ------------------------

1. Supported multi-Luns from 0 upto 4095, added "set-max-lun" command
to allow user to select the maxmium lun support, the default max lun
is 255. (CR29372)

2. Fixed the issue on fail to update the FC boot target when system
comes up from POST. (CR29373)

3. Fixed the issue for system hangs in scan disk if the link topology
changed after system firmware discovered the bootable lun with
a different topology. (CR29019)

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA Changes and Corrections:

Corrected response in a RCV_SEQ_LIST64 IOCB. (CR 11220)

Ensure that there is at least one credit when doing REG LOGIN to
fabric port. (CR 12460, 12466, 14357)

Parity errors due to loop init received during speed negotiation
are now processed properly. (CR 13463, 14239, 14241)

Corrected a problem where the download of corrupted firmware would
return the proper error, but refuse any further commands.
(CR 13241, 14584)

Improved handling of the RESET_RING command to completely initialize
the ring and no longer return an unnecessary response.
(CR 13325, 13631, 13632, 13374, 14446, 14450, 14589)

Ensure that no frames waiting for resources are accidentally released
on to the link when killing exchanges.
(CR 12183, 13630, 14591, 14447)

Invalid exchange handling was improved by not issuing an error when
buffers are returned for use. (CR 13413, 14593)

Added code to correctly process and count error counter overflows.
(CR 13328, 13629, 14444, 14594)

Receiving a LIP while loop master and while waiting for LIHA will no
longer cause a timeout. (CR 13636, 13638, 14448, 14595)

Response to an unsolicited IP broadcast frame was corrected to comply
with FC spec. (CR 11019, 14596)

Corrected a dropped IWRITE command when using discontinuous buffer
descriptor entries (BDEs). (CR 10342, 10447, 14597)

Allow use of a different FLASH memory chip [AM29LV160DB].
(CR 14599, 13059, 12545)

An uninitialized value (usually zero) was being returned for the ED_TOV
value when a default value of 10 was actually being used by the
firmware. The reported value is now correctly intialized to 10.
(CR 14108, 14603)

Corrected the reason and explanation codes given to the tape drive
in an LS_RJT response to REC ELS. This allows a Solaris host to
retry the command. (CR 10121, 9489)

Development, desk checks and source code review found possible problems
that had no reported instances of failure.
(CR 14066, 14359, 13393, 14586, 14115, 14602, 11934, 14604, 11933,
14605, 11932, 14606, 11931, 14607, 14751)

If you use LP6DUTIL to upgrade the firmware, you must use version
8.6a4 or higher. The latest version of LP6DUTIL is included in
this kit.

Several files, such as the .DWC files and /prg_kit/ files, have been
eliminated from this kit in order to simplify the update process and
ensure correct operation of the updated HBA.

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA Table of Contents
Installation
Compatability
Prerequisites
Set Jumpers
Install HBA
Attach Media
Apply Power
View LEDs
Reference
Specifications
FCC and Regulatory Notices
Declaration of
Conformity
Laser Safety

Prerequisites
The host computer must provide 3.3 VDC bus power (a power LED on
the bracket shows bus power)
·
One open 32-bit or 64-bit (64-bit recommended) cPCI bus slot can be
either 3.3 VDC or 5.0 VDC signaling interface
·
· PCI bus clock rate of 66 MHz is preferred
· Media and connectors

Install the Host Bus Adapter Board
Record IEEE and serial numbers.
Each host bus adapter port is shipped with a unique address identifier
called the IEEE address. Since this adapter has two ports, there are two
IEEE addresses. The IEEE address is used when configuring your
system. The serial number is used when communicating with Emulex.
All numbers are clearly marked on the board. We recommend that you
record these numbers before installing the adapter.
Turn off the computer.
Remove the blank panel from an empty 32- or 64-bit cPCI bus slot, or
remove the existing HBA.
With the lever open, hold the LP9002C board by the two side edges or
the bracket, and slide the card into the slot between the two guides.
Press on the front panel to completely seat the card in the I/O
assembly.Push the lever in to lock the lever. You should feel it click.

Bus Type cPCI
Max Bus Speed 66 MHz
Product Type HBA Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.

Base driver, HBAnyware utility 2.1a18, HBAnyware Security Configurator 2.1a18 and lputil 2.0a9

HBAnyware 2.1a18 Solaris Installation Instructions

Dependencies:

lpfcdriver 6.02c, or later
hbaapi 2.0e

Java Runtime Environment

Version 1.4 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

HBAnyware and hbacmd currently will not run under Solaris 6.

The JRE and instructions for installation can be found at http://java.sun.com/downloads/index.html

JAVA NOTE:
HBAnyware needs the java runtime binaries and libraries, so their path needs to be included in the PATH
environment variable. For example, if your java runtime binaries are in /usr/java/bin, then include this path
in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware is dependant on lpfcdriver being installed, so install lpfcdriver first if it is not already installed.

1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Copy the HBAnyware-2.1a18-sparc.tar.gz file to a directory on the install machine
3. cd to the directory which you copied the tar file
4. Unzip the file: gunzip HBAnyware-2.1a18-sparc.tar.gz
5. Untar the file: tar -xvf HBAnyware-2.1a18-sparc.tar
6. Run the pkgadd routine: pkgadd -d .
7. When prompted by pkadd, choose to install HBAnyware
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

emlxadm version 1.00r and emlxdrv version 1.00k for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (75.5 KB tar file)

Installing and using the FCA utilities

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Base driver, HBAnyware utility 2.1a18, HBAnyware Security Configurator 2.1a18 and lputil 2.0a9

HBAnyware 2.1a18 Solaris Installation Instructions

Dependencies:

lpfcdriver 6.02c, or later
hbaapi 2.0e

Java Runtime Environment

Version 1.4 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

HBAnyware and hbacmd currently will not run under Solaris 6.

The JRE and instructions for installation can be found at http://java.sun.com/downloads/index.html

JAVA NOTE:
HBAnyware needs the java runtime binaries and libraries, so their path needs to be included in the PATH
environment variable. For example, if your java runtime binaries are in /usr/java/bin, then include this path
in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware is dependant on lpfcdriver being installed, so install lpfcdriver first if it is not already installed.

1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Copy the HBAnyware-2.1a18-sparc.tar.gz file to a directory on the install machine
3. cd to the directory which you copied the tar file
4. Unzip the file: gunzip HBAnyware-2.1a18-sparc.tar.gz
5. Untar the file: tar -xvf HBAnyware-2.1a18-sparc.tar
6. Run the pkgadd routine: pkgadd -d .
7. When prompted by pkadd, choose to install HBAnyware
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

emlxadm version 1.00q and emlxdrv version 1.00j for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (77 KB tar file)

Installing and using the FCA utilities

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Base driver, HBAnyware utility 2.1a18, HBAnyware Security Configurator 2.1a18 and lputil 2.0a9

This kit contains the following components:

lpfc-6.02f-sparc.tar - Emulex Fibre Channel Solaris Driver
EmlxApps300a39-Solaris.tar - Emulex Applications kit
readme.first.txt - this file

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found on the
Emulex website - www.emulex.com, under /ts/docfc/solframe.htm.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications kit
can be found in the README.txt file contained in the EmlxApps300a39-Solaris.tar package.

Installation, Configuration and Troubleshooting (2,727 KB)

emlxadm version 1.00q and emlxdrv version 1.00j for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (77 KB tar file)

Installing and using the FCA utilities

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Base driver, HBAnyware utility 3.4a15, emlxdrv utility 1.00l; emlxdrv is needed for a fresh installation of Solaris 10 Update 1

HBAnyware 3.4a15 Solaris Installation Instructions

Dependencies:

lpfcdriver 6.21a, emlxsdriver 2.20a, or later
hbaapi 2.0.f

Java Runtime Environment

Version 1.5 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

HBAnyware and hbacmd currently will not run under Solaris 6. HBAnyware and hbacmd target OS versions
include Solaris 5.8, 5.9, 5.10, and 5.11.

The JRE and instructions for installation can be found at http://java.sun.com/downloads/index.html

JAVA NOTE:
HBAnyware needs the java runtime binaries and libraries, so their path needs to be included in the PATH
environment variable. For example, if your java runtime binaries are in /usr/java/bin, then include this path
in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware is dependant on a driver being installed, so install lpfcdriver or emlxsdriver first if it is not already installed.

1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Run the unpack script : ./unpack_apps
to obtain correct package version
3. Unzip the file: gunzip HBAnyware-3.4a15-sparc.tar.gz
4. Untar the file: tar -xvf HBAnyware-3.4a15-sparc.tar
5. Run the pkgadd utility: pkgadd -d .
6. When prompted by pkgadd, choose to install HBAnyware
7. When prompted by pkgadd, answer the HBAnyware installation option questions
Running the HBAnyware GUI

1. su to root
2. Run the script /opt/emulex/hbanyware/hbanyware

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
LPFC Driver for Solaris User Manual (1.58 MB)

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
HBAnyware Utility User Manual

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
emlxadm version 1.01a and emlxdrv version 1.00k for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (75.5 KB tar file)

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Instructions for using emlxdrv

Introduction.............................................................................................................. 1
Fibre Channel Overview .................................................................................... 1
The Solaris Fibre Channel Stack ....................................................................... 1
Installing the Utilities................................................................................................ 3
Compatibility...................................................................................................... 3
Installing or Updating the Utilities Using the emlxu_install Script....................... 4
Removing the Utilities Using the emlxu_remove Script ..................................... 5
Installing the Utilities Package Manually............................................................ 6
Removing the Utilities Package Manually.......................................................... 7
Updating the Utilities Package Manually ........................................................... 7
Using the emlxadm Utility ........................................................................................ 8
Modes of Operation (emlxadm) ......................................................................... 8
Interactive Mode (emlxadm)........................................................................ 8
CLI Mode (emlxadm)................................................................................... 9
Command Descriptions (emlxadm) ................................................................. 11
Using the emlxdrv Utility ........................................................................................ 31
Modes of Operation (emlxdrv) ......................................................................... 31
Interactive Mode (emlxdrv)........................................................................ 31
CLI Mode (emlxdrv)................................................................................... 33
Command Descriptions (emlxdrv) ................................................................... 33

This document provides the information needed to use the Emulex® emlxadm and elmxdrv utility
programs. For system administrators, this document includes information about the installation and
removal of these utilities.
At the very least, system administrators should be familiar with Solaris and the Sun StorEdge SAN
Foundation Software (SFS) and should have access to standard system documentation. Anyone
working with this product should have some familiarity with the nature and use of Fibre Channel.

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with this Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Base driver, HBAnyware utility 3.3a22 and lputil 2.0a13 (21.5 MB tar file)

Solaris 10 Updates and the lpfc
Driver
The behavior of the Solaris operating system changes beginning with Solaris 10 Update 1 (also referred
to as Solaris 10 1/06 release). Starting with this version, a bare-metal installation of the operating system
automatically discovers all SFS-recognized HBAs (Sun-branded, Emulex, or EMC-branded) and binds
them to the “emlxs” SFS driver. A subsequent installation of lpfc will not discover and bind these HBAs;
you must use the emlxdrv utility to unbind the HBAs from the SFS driver as described in this document.

Note: You do not need to follow the procedure described in this document in the following
circumstances:
• If the server contains any Sun-branded HBAs, which are recognized
and supported only by the emlxs driver and not by the lpfc driver; you
must use the emlxs driver on all HBAs.
• If you installed an earlier version of Solaris and bound the HBAs to the
lpfc driver; updating to Solaris 10 Update 1 (or later) by applying
patches will not unbind the HBAs from the lpfc driver.

Prerequisites:
• SPARC platform
• Solaris 10 Update 1 or later installed on a local drive
• Sun released patch 120222-06 or later installed
• Emulex® FCA utility version 1.00m (which includes emlxdrv 1.00j for SPARC) or later installed
(see the Emulex FCA Utilities Reference Manual for installation instructions)
• Emulex lpfc driver not yet installed
To unbind the HBAs from the SFS driver, do the following:
1. Start the emlxdrv utility as described in the Emulex FCA Utilities Reference Manual.
2. Type the following command at the emlxdrv prompt:
clear_all
This unbinds from emlxs all HBAs that are recognized by both emlxs and lpfc drivers.
3. Exit the emlxdrv utility by typing the following:
q
Install the lpfc driver as instructed in the documentation that accompanies the driver.

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with this Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with this Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with this Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.

Introduction.............................................................................................................. 1
Installing lputil .......................................................................................................... 1
Starting lputil............................................................................................................ 2
Discovering HBAs.................................................................................................... 4
Viewing HBA Information......................................................................................... 4
Resetting an HBA .................................................................................................... 5
Updating an HBA’s Firmware or Boot Code ............................................................. 5
Enabling or Disabling Boot Code ............................................................................. 6
Downloading PCI Configuration............................................................................... 7
Setting Up Persistent Binding (Solaris Only)............................................................ 7
Using the Command Line Interface ......................................................................... 9
Examples of lputil Commands................................................................... 11

Introduction
The LightPulse® diagnostic utility (lputil) for Linux and Solaris is a console application that enables you
to manage local Emulex® host bus adapters (HBAs).
Use lputil to do any of the following:
• Discover HBAs
• View HBA information
• Reset HBAs
• Update firmware or boot code on the local HBA
• Enable or disable the boot code on the HBA
• Download PCI Configuration
• Set Up Persistent Binding (Solaris only)
• Use the Command Line Interface (CLI)
Prerequisites
Before using lputil, ensure the following prerequisites are met:
• The Emulex driver is installed.
• The lputil utility is installed.
• If you are updating firmware, the firmware file is downloaded to a local drive. Firmware versions
differ between HBA versions. Make sure you have downloaded the appropriate firmware for your
HBA.
• I/O activity on the bus is quieted.
• Any software that relies on the HBA to be available is stopped or paused.
Installing lputil
To install lputil:
1. Download the lputil.tar file from the Emulex Web site to a directory on a local drive on the server.
2. Untar the contents of the lputil.tar file.
3. Run the lputil installation script.

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with this Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
emlxadm version 1.01a and emlxdrv version 1.00k for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (75.5 KB tar file)

Base driver, HBAnyware utility 3.1a12 and lputil 2.0a13

HBAnyware 3.1a12 Solaris Installation Instructions

Dependencies:

lpfcdriver 6.11c, emlxsdriver 2.20a, or later
hbaapi 2.0f

Java Runtime Environment

Version 1.5 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

HBAnyware and hbacmd currently will not run under Solaris 6. HBAnyware and hbacmd target OS versions
include Solaris 5.8, 5.9, and 5.10.

The JRE and instructions for installation can be found at http://java.sun.com/downloads/index.html

JAVA NOTE:
HBAnyware needs the java runtime binaries and libraries, so their path needs to be included in the PATH
environment variable. For example, if your java runtime binaries are in /usr/java/bin, then include this path
in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware is dependant on a driver being installed, so install lpfcdriver or emlxsdriver first if it is not already installed.

1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Run the unpack script : ./unpack_apps
to obtain correct package version
3. Unzip the file: gunzip HBAnyware-3.1a12-sparc.tar.gz
4. Untar the file: tar -xvf HBAnyware-3.1a12-sparc.tar
5. Run the pkgadd utility: pkgadd -d .
6. When prompted by pkadd, choose to install HBAnyware
7. When prompted by pkadd, answer the HBAnyware installation option questions
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

emlxadm version 1.01a and emlxdrv version 1.00k for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (75.5 KB tar file)

Emulex recommends installing driver version 6.10gx2, which adds a critical fix to the previously posted 6.10g driver. Driver functionality and behavior are otherwise identical.
Base driver, HBAnyware utility 3.0a17 and lputil 2.0a13

HBAnyware 3.0a17 Solaris Installation Instructions

Dependencies:

lpfcdriver 6.10b, or later
hbaapi 2.0f

Java Runtime Environment

Version 1.4 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

HBAnyware and hbacmd currently will not run under Solaris 6. HBAnyware and hbacmd target OS versions
include Solaris 5.8, 5.9, and 5.10.

The JRE and instructions for installation can be found at http://java.sun.com/downloads/index.html

JAVA NOTE:
HBAnyware needs the java runtime binaries and libraries, so their path needs to be included in the PATH
environment variable. For example, if your java runtime binaries are in /usr/java/bin, then include this path
in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware is dependant on lpfcdriver being installed, so install lpfcdriver first if it is not already installed.

1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Run the unpack script : ./unpack_apps
to obtain correct package version
3. Unzip the file: gunzip HBAnyware-3.0a17-sparc.tar.gz
4. Untar the file: tar -xvf HBAnyware-3.0a17-sparc.tar
5. Run the pkgadd utility: pkgadd -d .
6. When prompted by pkadd, choose to install HBAnyware
7. When prompted by pkadd, answer the HBAnyware installation option questions
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

Emulex recommends installing driver version 6.10gx2, which adds a critical fix to the previously posted 6.10g driver. Driver functionality and behavior are otherwise identical.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Emulex recommends installing driver version 6.10gx2, which adds a critical fix to the previously posted 6.10g driver. Driver functionality and behavior are otherwise identical.
emlxadm version 1.00r and emlxdrv version 1.00k for SPARC; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (75.5 KB tar file)

Emulex recommends installing driver version 6.10gx2, which adds a critical fix to the previously posted 6.10g driver. Driver functionality and behavior are otherwise identical.
Installing and using the FCA utilities

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver is posted as is, with no new version planned.
This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Base driver, HBAnyware utility 4.0a37, emlxdrv utility 1.00m; emlxdrv is needed for a fresh installation of Solaris 10 Update 1

HBAnyware 4.0a37 Solaris Installation Instructions

Dependencies:

lpfc driver 6.30g or later
hbaapi 2.0.f
Java Runtime Environment

Version 1.5 or later of the Java Runtime Environment (JRE) must
be installed. HBAnyware will not run under earlier versions of
the JRE.

The JRE and instructions for installation can be found at http://java.com.

JAVA NOTE:
HBAnyware needs the Java runtime binaries and libraries, so their path needs to be included
in the PATH environment variable. For example, if your java runtime binaries are in /usr/java/bin,
then include this path in your PATH environment variable. (bash> export PATH="$PATH:/usr/java/bin")


HBAnyware and hbacmd currently will not run under Solaris 6. The HBAnyware and hbacmd target OS versions
include Solaris 5.8, 5.9, and 5.10.

HBAnyware is dependent on the Emulex lpfc driver being installed. Please ensure that this package is
installed prior to installing HBAnyware.

HBAnyware Installation Instructions
-----------------------------------
1. Run the pkgrm routine to remove any previous version of HBAnyware: pkgrm HBAnyware
2. Run the unpack script : ./unpack_apps
to obtain correct package version
3. Unzip the file: gunzip HBAnyware-4.0a37-sparc.tar.gz
4. Untar the file: tar -xvf HBAnyware-4.0a37-sparc.tar
5. Run the pkgadd utility: pkgadd -d .
6. When prompted by pkgadd, choose to install HBAnyware
7. When prompted by pkgadd, answer the HBAnyware installation option questions
Running the HBAnyware GUI
-------------------------
1. su to root
2. Execute the command: /opt/HBAnyware/hbanyware

Note This driver is posted as is, with no new version planned.
This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
LPFC Driver for Solaris User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver is posted as is, with no new version planned.
This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
HBAnyware Utility Version 4.0

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

This driver is posted as is, with no new version planned.
This driver version requires patch #112438 for Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Instructions for using the FCA utilities

Introduction.............................................................................................................. 1
Fibre Channel Overview .................................................................................... 1
The Solaris Fibre Channel Stack ....................................................................... 1
Installing the Utilities................................................................................................ 3
Compatibility...................................................................................................... 3
Installing or Updating the Utilities Using the emlxu_install Script....................... 4
Removing the Utilities Using the emlxu_remove Script ..................................... 5
Installing the Utilities Package Manually............................................................ 6
Removing the Utilities Package Manually.......................................................... 7
Updating the Utilities Package Manually ........................................................... 7
Using the emlxadm Utility ........................................................................................ 8
Modes of Operation (emlxadm) ......................................................................... 8
Interactive Mode (emlxadm)........................................................................ 8
CLI Mode (emlxadm)................................................................................... 9
Command Descriptions (emlxadm) ................................................................. 11
Using the emlxdrv Utility ........................................................................................ 31
Modes of Operation (emlxdrv) ......................................................................... 31
Interactive Mode (emlxdrv)........................................................................ 31
CLI Mode (emlxdrv)................................................................................... 33
Command Descriptions (emlxdrv) ................................................................... 33

This document provides the information needed to use the Emulex® emlxadm and elmxdrv utility
programs. For system administrators, this document includes information about the installation and
removal of these utilities.
At the very least, system administrators should be familiar with Solaris and the Sun StorEdge SAN
Foundation Software (SFS) and should have access to standard system documentation. Anyone
working with this product should have some familiarity with the nature and use of Fibre Channel.

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Base driver, HBAnyware utility 3.4a15, emlxdrv utility 1.00l; emlxdrv is needed for a fresh installation of Solaris 10 Update 1 (21.5 MB tar file)

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
LPFC Driver for Solaris User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
HBAnyware Utility User Manual

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

This driver version requires patch #112438 for
Solaris 8 operation.
Starting with Solaris driver version 6.20, the driver no longer uses the sd.conf and st.conf files to limit the storage presented to the OS. If your environment uses these files to perform LUN or target masking, refer to the driver manual for important configuration information.
Instructions for using emlxdrv

Introduction.............................................................................................................. 1
Fibre Channel Overview .................................................................................... 1
The Solaris Fibre Channel Stack ....................................................................... 1
Installing the Utilities................................................................................................ 3
Compatibility...................................................................................................... 3
Installing or Updating the Utilities Using the emlxu_install Script....................... 4
Removing the Utilities Using the emlxu_remove Script ..................................... 5
Installing the Utilities Package Manually............................................................ 6
Removing the Utilities Package Manually.......................................................... 7
Updating the Utilities Package Manually ........................................................... 7
Using the emlxadm Utility ........................................................................................ 8
Modes of Operation (emlxadm) ......................................................................... 8
Interactive Mode (emlxadm)........................................................................ 8
CLI Mode (emlxadm)................................................................................... 9
Command Descriptions (emlxadm) ................................................................. 11
Using the emlxdrv Utility ........................................................................................ 31
Modes of Operation (emlxdrv) ......................................................................... 31
Interactive Mode (emlxdrv)........................................................................ 31
CLI Mode (emlxdrv)................................................................................... 33
Command Descriptions (emlxdrv) ................................................................... 33

This document provides the information needed to use the Emulex® emlxadm and elmxdrv utility
programs. For system administrators, this document includes information about the installation and
removal of these utilities.
At the very least, system administrators should be familiar with Solaris and the Sun StorEdge SAN
Foundation Software (SFS) and should have access to standard system documentation. Anyone
working with this product should have some familiarity with the nature and use of Fibre Channel.