Emulex LP850 Download Drivers and Manual

Available 65 files for LP850
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Driver
2.20e
Size Driver
59Kb
File Name
nw220e.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.20e September 30, 2005
This Readme file contains the description of the 2.20e version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 3 (NW65SP3)
- NetWare 6.0 with Support Pack 5 (NW6SP5 )
- NetWare 5.1 with Support Pack 7 (NW51SP7)
- untested with Netware 5.0 with Support Pack 6a (SP6a).
Netware 5.0 is supported by Novell, however no future work is planned for this version.
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Manual
2.20e
Size Manual
429Kb
File Name
manual.pdf
Information
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Driver
2.14b
Size Driver
54Kb
File Name
nw214b.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.14b Jul 09, 2004
This Readme file contains the description of the 2.14b version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Service Pack 2 (NW65SP2)
- NetWare 6.0 with Service Pack 4 (NW6SP4 )
- NetWare 5.1 with Service Pack 7 (NW51SP7)
- untested with Netware 5.0 with Service Pack 6a (SP6a).
Netware 5.0 is supported by Novell, however no future work is planned for this version.
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP10000 series adapters (minimum firmware revision 1.90a4)
- LP1050 series adapters (minimum firmware revision 1.90a4)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.90a4)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Manual
2.14b
Size Manual
452Kb
File Name
set.pdf
Information
Downloading the Emulex Driver for NetWare
Version 2.14b
Table of Contents
Supported Features
New Features in this Release
Prerequisites
Compatibility
Things to Know Before You Download
Known Issues
Files Included in this Release

Installing the Emulex Driver for NetWare
Version 2.14b
Table of Contents
Driver Information
Install Driver on New Netware Server
Install Driver on Existing Netware Server
Using an Emulex HBA to Boot Netware 6.5
Load and Update BootBIOS

Configuring the Emulex Driver for NetWare
Version 2.14b
Table of Contents
Introduction
Driver Parameters
Special Command Line Parameters

Troubleshooting the Emulex Driver for NetWare
Version 2.14b
Table of Contents
Introduction
Failback Detection Not Automatic
Only Eight LUNS are Seen
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Driver
2.12b
Size Driver
53Kb
File Name
nw212b.zip
Information
Novell "YES" Tested and Approved
Base driver

Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.12b Feb 12, 2004
This Readme file contains the description of the 2.12a version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Service Pack 1
- NetWare 6.0 with Service Pack 3 (SP3) and MM6UP1A patches
- NetWare 5.1 with Service Pack 6 (SP6)
- untested with Netware 5.0 with Service Pack 6a (SP6a).
Netware 5.0 is supported by Novell, however no future work is planned for this version.
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP10000 series adapters (minimum firmware revision 1.80a0)
- LP1050 series adapters (minimum firmware revision 1.80a0)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.01a2)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.90a7)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.90a7.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Manual
2.12b
Size Manual
484Kb
File Name
set.pdf
Information
Novell "YES" Tested and Approved
Installation, Configuration and Troubleshooting

Downloading the Emulex Driver for NetWare
Version 2.12b
Table of Contents
Prerequisites
Compatibility
Things to Know Before You Download
Changes and Corrections
Known Issues
Files Included in this Release

Installing the Emulex Driver for NetWare
Version 2.12b
Table of Contents
Driver Information
Install Driver on New Netware Server
Install Driver on Existing Netware Server
Using an Emulex HBA to Boot Netware 6.5
Load and Update BootBIOS

Configuring the Emulex Driver for NetWare
Version 2.12b
Table of Contents
Introduction
Driver Parameters
Special Command Line Parameters
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Driver
2.11b
Size Driver
53Kb
File Name
nw211b.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.11b Oct 19, 2003
This Readme file contains the description of the 2.11b version of the
LPFC.HAM driver for the Emulex LightPulse adapter family and Novell
NetWare 5.0, 5.1, and 6.0. It provides support for switched Fabric
operation and multi-initiator environments and for up to 16 adapter
channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5
- NetWare 6.0 with Service Pack 3 (SP3) and MM6UP1A patches
- NetWare 5.1 with Service Pack 6 (SP6)
- Netware 5.0 with Service Pack 6a. Netware 5.0 is supported by Novell, however no future work is planned for this version.
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP10000 series adapters (minimum firmware revision 1.80a0)
- LP1050 series adapters (minimum firmware revision 1.80a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.00a4)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.90a7)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.90a7.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
NetWare 5.0, 5.1, 6.0 and 6.5
Version Manual
2.11b
Size Manual
465Kb
File Name
set.pdf
Information
Downloading the Emulex Driver for NetWare
Version 2.11b
Table of ContentsPrerequisitesCompatibilityThings to Know Before You DownloadChanges and CorrectionsKnown IssuesFiles Included in this Release

Installing the Emulex Driver for NetWare
Version 2.11b
Table of ContentsDriver InformationInstall Driver on New Netware ServerInstall Driver on Existing Netware ServerUsing an Emulex HBA to Boot Netware 6.5Load and Update BootBIOS

Configuring the Emulex Driver for NetWare
Version 2.11b
Table of ContentsIntroductionDriver ParametersSpecial Command Line Parameters
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
5.31a0
Size Driver
17.2Mb
File Name
scsiportminiportkit_5-31a0-1e.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Base driver, HBAnyware utility 3.0a16 and lputilnt 1.8a18 (17.2 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
SMI-S Provider Kit
Operating Systems
Windows 2000-2003
Version Driver
5.31a0
Size Driver
6.9Mb
File Name
elxsmiprovider1.0.12-1.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
SMI-S HBA Provider, compliant with the SMI-S 1.0.2 specification and certified against the SNIA-CTP v1.0.2.23 suite. Pre-packaged with OpenPegasus CIMOM v2.3.2, as a turnkey SMI-S agent for ease of installation and deployment. (6.97 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
5.31a0
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installing the driver using AutoPilot Installer (468 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
5.31a0
Size Manual
4.3Mb
File Name
manual.pdf
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
5.30a2 32/64-Bit
Size Driver
18.4Mb
File Name
scsiportminiportkit_5-30a2-1d.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Base driver, HBAnyware utility 3.0a9 and lputilnt 1.8a18 (18 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
SMI-S Provider Kit
Operating Systems
Windows 2000-2003
Version Driver
5.30a2 32/64-Bit
Size Driver
6.9Mb
File Name
elxsmiprovider1.0.12-1.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
SMI-S HBA Provider, compliant with the SMI-S 1.0.2 specification and certified against the SNIA-CTP v1.0.2.23 suite
Pre-packaged with OpenPegasus CIMOM v2.3.2, as a turnkey SMI-S agent for ease of installation and deployment (6.97 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
5.30a2 32/64-Bit
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installing the driver using AutoPilot Installer (468 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
5.30a2 32/64-Bit
Size Manual
4.3Mb
File Name
manual.pdf
Information
SCSIport Miniport Driver
Windows Server 2003 Upgrade Notice: If you are currently running the Emulex SCSIport Miniport driver version 5.10a10 or earlier, follow these Upgrade Instructions before upgrading from Windows 2000 Server to Windows Server 2003.
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
5.20a9 32/64-Bit
Size Driver
14.3Mb
File Name
scsiportminiportkit_5-20a9-1d.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Base driver, HBAnyware utility 2.1a17 and lputilnt 1.8a15 (15 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
SMI-S Provider Kit
Operating Systems
Windows 2000-2003
Version Driver
5.20a9 32/64-Bit
Size Driver
6.9Mb
File Name
elxsmiprovider1.0.12-1.exe
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
SMI-S HBA Provider, compliant with the SMI-S 1.0.2 specification and certified against the SNIA-CTP v1.0.2.23 suite
Pre-packaged with OpenPegasus CIMOM v2.3.2, as a turnkey SMI-S agent for ease of installation and deployment (6.97 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
5.20a9 32/64-Bit
Size Driver
498Kb
File Name
quick_installation.pdf
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installing the driver using AutoPilot Installer (468 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
5.20a9 32/64-Bit
Size Manual
2.9Mb
File Name
manual.pdf
Information
Qualification: The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The 64-bit Itanium SCSIport Miniport driver is also Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition. The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit Base driver, HBAnyware utility 2.1a16 and lputilnt 1.8a13
Operating Systems
Windows 2000-2003
Version Driver
5.20a8 32/64-Bit
Size Driver
14Mb
File Name
scsiportminiportkit_5-20a8c-2g.exe
Information
Qualification: The driver for Windows Server 2003 is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium platforms. The driver for Windows 2000 Server is qualified and digitally signed by WHQL labs for Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install Installing the driver using AutoPilot Installer
Operating Systems
Windows 2000-2003
Version Driver
5.20a8 32/64-Bit
Size Driver
90Kb
File Name
quick_installation.pdf
Information
Qualification: The driver for Windows Server 2003 is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium platforms. The driver for Windows 2000 Server is qualified and digitally signed by WHQL labs for Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
OS Versions: Windows Server 2003 SP1 and Windows Server 2000 SP2
Installing the driver using AutoPilot Installer (3,085 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting
Operating Systems
Windows 2000-2003
Version Manual
5.20a8 32/64-Bit
Size Manual
2.9Mb
File Name
manual.pdf
Information
Qualification: The driver for Windows Server 2003 is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium platforms. The driver for Windows 2000 Server is qualified and digitally signed by WHQL labs for Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 64-bit Base driver, HBAnyware utility 2.0a21 and lputilnt 1.7a21
Operating Systems
Windows 2000-2003
Version Driver
5.10a10 64-Bit
Size Driver
6.1Mb
File Name
scsiport-6-5.10a10-sp1.zip
Information
Qualification: The 64-bit SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for both Windows Server 2003 and Windows Server 2003, Datacenter Edition.

This kit contains the following components:

ns6510a10dc.zip - Emulex Fibre Channel SCSIport Miniport Driver
Emlx64Apps20a21-SP1.zip - Emulex Applications kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

The installation for the Emulex Applications Kit has been updated
to install the hbaapi.dll file in the Emulex utilities directory
to be compatible with Windows Server 2003 Service Pack 1.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting
Operating Systems
Windows 2000-2003
Version Manual
5.10a10 64-Bit
Size Manual
2.8Mb
File Name
manual_ws3.pdf
Information
Qualification: The 64-bit SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for both Windows Server 2003 and Windows Server 2003, Datacenter Edition.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 32-bit Base driver, HBAnyware utility 2.0a21 and lputilnt 1.7a21
Operating Systems
Windows 2000-2003
Version Driver
5.10a10 32-Bit
Size Driver
5.2Mb
File Name
scsiport-5-5.10a10-sp1.zip
Information
Qualification: The 32-bit SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, and it is Microsoft WHQL qualified and digitally signed for Windows 2000 Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.

This kit contains the following components:

ns5510a10sc.zip - Emulex Fibre Channel SCSIport Miniport Driver
EmlxApps20a21-SP1.zip - Emulex Applications kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

The installation for the Emulex Applications Kit has been updated
to install the hbaapi.dll file in the Emulex utilities directory
to be compatible with Windows Server 2003 Service Pack 1.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting for Windows Server 2003
Operating Systems
Windows 2000-2003
Version Manual
5.10a10 32-Bit
Size Manual
2.8Mb
File Name
manual_ws3.pdf
Information
Qualification: The 32-bit SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, and it is Microsoft WHQL qualified and digitally signed for Windows 2000 Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting for Windows 2000 Server
Operating Systems
Windows 2000-2003
Version Manual
5.10a10 32-Bit
Size Manual
2.9Mb
File Name
manual_w2k.pdf
Information
Qualification: The 32-bit SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, and it is Microsoft WHQL qualified and digitally signed for Windows 2000 Server The SCSIport Miniport driver is Microsoft WHQL qualified and digitally signed for Windows 2000 Server.
For Windows 2000 Server, Service Pack 4 is required.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 64-bit Base driver, HBAnyware utility 2.0a21 and lputilnt 1.7a21
Operating Systems
Windows 2000-2003
Version Driver
5.10a9 64-Bit
Size Driver
6.1Mb
File Name
scsiport-6-5.10a9-sp1.zip
Information
Qualification: The 64-Bit SCSIport Miniport driver is qualified and digitally signed by WHQL labs.

This kit contains the following components:

ns6510a9dc.zip - Emulex Fibre Channel SCSIport Miniport Driver
Emlx64Apps20a21-SP1.zip - Emulex Applications kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

The installation for the Emulex Applications Kit has been updated
to install the hbaapi.dll file in the Emulex utilities directory
to be compatible with Windows Server 2003 Service Pack 1.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the ns6510a9dc.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting
Operating Systems
Windows 2000-2003
Version Manual
5.10a9 64-Bit
Size Manual
2.1Mb
File Name
manual_ws3.pdf
Information
Qualification: The 64-Bit SCSIport Miniport driver is qualified and digitally signed by WHQL labs.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 32-bit Base driver, HBAnyware utility 2.0a21 and lputilnt 1.7a21
Operating Systems
Windows 2000-2003
Version Driver
5.10a9 32-Bit
Size Driver
5.2Mb
File Name
scsiport-5-5.10a9-sp1.zip
Information
Qualification: The 32-Bit SCSIport Miniport driver is qualified and digitally signed by WHQL labs for Windows Server 2003 and Windows 2000 Server and Workstation products (Service Pack 2 or above).

This kit contains the following components:

ns5510a9sc.zip - Emulex Fibre Channel SCSIport Miniport Driver
EmlxApps20a21-SP1.zip - Emulex Applications kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

The installation for the Emulex Applications Kit has been updated to install
the hbaapi.dll file in the Emulex utilities directory to be compatible with
Windows Server 2003 Service Pack 1.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the ns5510a9sc.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
applications kit listed above.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting for Windows Server 2003
Operating Systems
Windows 2000-2003
Version Manual
5.10a9 32-Bit
Size Manual
2.1Mb
File Name
manual_ws3.pdf
Information
Qualification: The 32-Bit SCSIport Miniport driver is qualified and digitally signed by WHQL labs for Windows Server 2003 and Windows 2000 Server and Workstation products (Service Pack 2 or above).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting for Windows 2000 Server
Operating Systems
Windows 2000-2003
Version Manual
5.10a9 32-Bit
Size Manual
2.2Mb
File Name
manual_w2k.pdf
Information
Qualification: The 32-Bit SCSIport Miniport driver is qualified and digitally signed by WHQL labs for Windows Server 2003 and Windows 2000 Server and Workstation products (Service Pack 2 or above).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.42a0
Size Driver
13.8Mb
File Name
fcportkit_2-42a0-1c.exe
Information
Qualification:
The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server on x86 platforms.
The FC Port 2.42a0 driver has been qualified with the Universal WHQL program, which does not support Microsoft Cluster Server qualifications.
FC Port 2.22a8 Not Supported with SP1 and SP2
If you are using FC Port 2.22a8, you will be unable to install the Windows Server 2003 SP2 update. If you are using FC Port 2.22a8 and install the Windows Server 2003 SP1 update, the system will not boot after the SP1 installation
You should install the most current version of FC Port or Storport Miniport that has been qualified by your Emulex HBA service provider before installing SP1 or SP2. If you have installed SP1 with FC Port driver 2.22a8
Base driver, HBAnyware utility 2.1a21 and elxcfg version 1.41a17 (13.8 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.42a0
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for
WindowsServer 2003 on x86 platforms and Windows 2000 Server.
The FC Port 2.40a3 driver has been qualified with the Universal WHQL program,
which does not support Microsoft Cluster Server qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (496 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.42a0
Size Manual
3.1Mb
File Name
fcportmanual.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server on x86 platforms.
The FC Port 2.42a0 driver has been qualified with the Universal WHQL program, which does not support Microsoft Cluster Server qualifications.
FC Port 2.22a8 Not Supported with SP1 and SP2
If you are using FC Port 2.22a8, you will be unable to install the Windows Server 2003 SP2 update. See our knowledgebase article for more information. If you are using FC Port 2.22a8 and install the Windows Server 2003 SP1 update, the system will not boot after the SP1 installation
You should install the most current version of FC Port or Storport Miniport that has been qualified by your Emulex HBA service provider before installing SP1 or SP2. If you have installed SP1 with FC Port driver 2.22a8, see our knowledgebase article for help on how to recover your system.
Installation, Configuration and Troubleshooting (3.12 MB)

Introduction.............................................................................................................. 1
Definitions ......................................................................................................... 1
Important Considerations......................................................................................... 2
Changing Driver Types...................................................................................... 2
Updating the FC Port Driver Using AutoPilot Installer ....................................... 2
Using the FC Port Driver in a Windows 2000 Server System ............................ 2
Upgrading to Windows Server 2003 Service Pack 1 ......................................... 2
Definitions................................................................................................................ 3
FC Port Driver Information....................................................................................... 3
Prerequisites ..................................................................................................... 3
Compatibility...................................................................................................... 3
Update the FC Port Driver Using AutoPilot Installer .......................................... 4
Known Issues .................................................................................................... 4
Files Included in the AutoPilot Installer™ ................................................................ 4
Distribution Executable File Overview ..................................................................... 5
Distribution Executable File Procedure.............................................................. 5
AutoPilot Installer..................................................................................................... 5
Introduction ....................................................................................................... 5
Prerequisites ............................................................................................... 5
AutoPilot Installer Features ......................................................................... 6
Configuration Questions.............................................................................. 6
Installation Planning .......................................................................................... 6
Hardware-First Installation................................................................................. 6
Prerequisites ............................................................................................... 6
Procedure ................................................................................................... 7
If the Installation Fails ................................................................................. 8
Software-First Installation .................................................................................. 8
Prerequisites ............................................................................................... 8
Procedure ................................................................................................... 8
HBAnyware Security Configurator Installation ....................................................... 10
Prerequisites ............................................................................................. 10
Procedure ................................................................................................. 10
Unattended Installation .......................................................................................... 11
Prerequisites ................................................................................................... 11
AutoPilot Configuration File Format................................................................. 11
Mandatory Configuration File Changes ........................................................... 11
Delete Questions in the APInstall.cfg File........................................................ 12
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.41a1 32-Bit
Size Driver
13.8Mb
File Name
fcportkit_2-41a1-1b.exe
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server on x86 platforms.
The FC Port 2.41a1 driver has been qualified with the Universal WHQL program, which does not support Microsoft Cluster Server qualifications.
FC Port 2.22a8 Not Supported with SP1 and SP2
If you're using FC Port 2.22a8, you will be unable to install the Windows Server 2003 SP2 update. If you're using FC Port 2.22a8 and install the Windows Server 2003 SP1 update, the system will not boot after the SP1 installation.
You should install the most current version of FC Port or Storport Miniport that has been qualified by your Emulex HBA service provider before installing SP1 or SP2. If you have installed SP1 with FC Port driver 2.22a8.
Base driver, HBAnyware utility 2.1a21 and elxcfg version 1.41a17 (13.8 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.41a1 32-Bit
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for
WindowsServer 2003 on x86 platforms and Windows 2000 Server.
The FC Port 2.40a3 driver has been qualified with the Universal WHQL program,
which does not support Microsoft Cluster Server qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (496 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.41a1 32-Bit
Size Manual
3.1Mb
File Name
fcportmanual.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server on x86 platforms.
The FC Port 2.42a0 driver has been qualified with the Universal WHQL program, which does not support Microsoft Cluster Server qualifications.
FC Port 2.22a8 Not Supported with SP1 and SP2
If you are using FC Port 2.22a8, you will be unable to install the Windows Server 2003 SP2 update. See our knowledgebase article for more information. If you are using FC Port 2.22a8 and install the Windows Server 2003 SP1 update, the system will not boot after the SP1 installation
You should install the most current version of FC Port or Storport Miniport that has been qualified by your Emulex HBA service provider before installing SP1 or SP2. If you have installed SP1 with FC Port driver 2.22a8, see our knowledgebase article for help on how to recover your system.
Installation, Configuration and Troubleshooting (3.12 MB)

Introduction.............................................................................................................. 1
Definitions ......................................................................................................... 1
Important Considerations......................................................................................... 2
Changing Driver Types...................................................................................... 2
Updating the FC Port Driver Using AutoPilot Installer ....................................... 2
Using the FC Port Driver in a Windows 2000 Server System ............................ 2
Upgrading to Windows Server 2003 Service Pack 1 ......................................... 2
Definitions................................................................................................................ 3
FC Port Driver Information....................................................................................... 3
Prerequisites ..................................................................................................... 3
Compatibility...................................................................................................... 3
Update the FC Port Driver Using AutoPilot Installer .......................................... 4
Known Issues .................................................................................................... 4
Files Included in the AutoPilot Installer™ ................................................................ 4
Distribution Executable File Overview ..................................................................... 5
Distribution Executable File Procedure.............................................................. 5
AutoPilot Installer..................................................................................................... 5
Introduction ....................................................................................................... 5
Prerequisites ............................................................................................... 5
AutoPilot Installer Features ......................................................................... 6
Configuration Questions.............................................................................. 6
Installation Planning .......................................................................................... 6
Hardware-First Installation................................................................................. 6
Prerequisites ............................................................................................... 6
Procedure ................................................................................................... 7
If the Installation Fails ................................................................................. 8
Software-First Installation .................................................................................. 8
Prerequisites ............................................................................................... 8
Procedure ................................................................................................... 8
HBAnyware Security Configurator Installation ....................................................... 10
Prerequisites ............................................................................................. 10
Procedure ................................................................................................. 10
Unattended Installation .......................................................................................... 11
Prerequisites ................................................................................................... 11
AutoPilot Configuration File Format................................................................. 11
Mandatory Configuration File Changes ........................................................... 11
Delete Questions in the APInstall.cfg File........................................................ 12
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.40a3 32-Bit
Size Driver
13.8Mb
File Name
fcportkit_2.40a3-1b.exe
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for
WindowsServer 2003 on x86 platforms and Windows 2000 Server.
The FC Port 2.40a3 driver has been qualified with the Universal WHQL program,
which does not support Microsoft Cluster Server qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Base driver, HBAnyware utility 2.1a21 and elxcfg version 1.41a17 (14 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.40a3 32-Bit
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for
WindowsServer 2003 on x86 platforms and Windows 2000 Server.
The FC Port 2.40a3 driver has been qualified with the Universal WHQL program,
which does not support Microsoft Cluster Server qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (496 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.40a2 32-Bit
Size Driver
13.8Mb
File Name
fcportkit_2-40a2-1a.exe
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
FC Port 2.40a2 has been qualified with the Universal WHQL program, which does not support cluster qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Base driver, HBAnyware utility 2.1a17 and elxcfg version 1.41a17 (14 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.40a2 32-Bit
Size Driver
496Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
FC Port 2.40a2 has been qualified with the Universal WHQL program, which does not support cluster qualifications.
SP1 Boot Failure with FC Port 2.22a8 Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (496 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.40a2 32-Bit
Size Manual
2.9Mb
File Name
manual.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
FC Port 2.40a2 has been qualified with the Universal WHQL program, which does not support cluster qualifications.
SP1 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8, see Solution ID: 17931 for help on how to recover your system.
Installation, Configuration and Troubleshooting (2.58 MB)

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.30a2 32/64-Bit
Size Driver
14.2Mb
File Name
fcportkit_2-30a2c-3f.exe
Information
Qualification: The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition for the x86 platform. The FC Port driver is Microsoft WHQL qualified for Windows 2000 Server.
For Windows 2000 Server, Service pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1. More Information
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Base driver, HBAnyware utility 2.1a16 and elxcfg version 1.41a16 (14,474 KB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.30a2 32/64-Bit
Size Driver
90Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition for the x86 platform. The FC Port driver is Microsoft WHQL qualified for Windows 2000 Server.
For Windows 2000 Server, Service pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1. More Information
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (90 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.30a2 32/64-Bit
Size Manual
1.4Mb
File Name
manual.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003 on x86 and Itanium 64-bit platforms. The FC Port driver is Microsoft WHQL qualified and digitally signed for Windows Server 2003, Datacenter Edition for the x86 platform. The FC Port driver is Microsoft WHQL qualified for Windows 2000 Server.
For Windows 2000 Server, Service pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1. More Information
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2000-2003
Version Driver
2.23a6 32/64-Bit
Size Driver
12.8Mb
File Name
fcportkit_2-23a6c-4e.exe
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
For Windows 2000 drivers, Service Pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Base driver, HBAnyware utility 2.1a9 and elxcfg version 1.41a14 (13,156 KB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2000-2003
Version Driver
2.23a6 32/64-Bit
Size Driver
90Kb
File Name
quick_installation.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
For Windows 2000 drivers, Service Pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installing the driver using AutoPilot Installer (496 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2000-2003
Version Manual
2.23a6 32/64-Bit
Size Manual
1.5Mb
File Name
manual.pdf
Information
Qualification: The FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
For Windows 2000 drivers, Service Pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Installation, Configuration and Troubleshooting (1,574 KB)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 64-bit
Operating Systems
Windows 2000-2003
Version Driver
2.22a8 64-Bit
Size Driver
6.3Mb
File Name
port-6-2.22a8-3b.zip
Information
Qualification: 64-bit FC Port driver is Microsoft WHQL qualified for Windows Server 2003.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Base driver, HBAnyware utility 2.0a13 and elxcfg version 1.41a14

This kit contains the following components:
sli222a8ia64c.zip - Emulex Fibre Channel Multi-protocol Port Driver
Emlx64Apps300a7.zip - Emulex Applications kit
Readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the sli222a8ia64c.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.doc file contained in the
Emlx64Apps300a7.zip package.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting
Operating Systems
Windows 2000-2003
Version Manual
2.22a8 64-Bit
Size Manual
1.9Mb
File Name
set_ws3.pdf
Information
Qualification: 64-bit FC Port driver is Microsoft WHQL qualified for Windows Server 2003.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit 32-bit
Operating Systems
Windows 2000-2003
Version Driver
2.22a8 32-Bit
Size Driver
5.4Mb
File Name
port-5-2.22a8-3a.zip
Information
Qualification: 32-bit FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
For Windows 2000 drivers, Service Pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8

This kit contains the following components:

sli222a8win2ks.zip - Emulex Fibre Channel Multi-protocol Port Driver
EmlxApps300a7.zip - Emulex Applications kit
Readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the sli222a8win2ks.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.doc file contained in the
EmlxApps300a7.zip package.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual Installation, Configuration and Troubleshooting
Operating Systems
Windows 2000-2003
Version Manual
2.22a8 32-Bit
Size Manual
1.8Mb
File Name
set_w2k.pdf
Information
Qualification: 32-bit FC Port driver is Microsoft WHQL qualified for Windows Server 2003 and Windows 2000 Server.
For Windows 2000 drivers, Service Pack 4 is required for cluster configurations.
Windows Server 2003 SP1 Upgrade Notice
New versions are available for all Emulex drivers that include support for Windows Server 2003 SP1. We recommend that you upgrade to one of these new drivers. In most cases, older drivers can be configured to work with SP1 by running the HBA API-SP1 Migration program prior to installing SP1.
SP1/R2 Boot Failure with FC Port 2.22a8
Windows Server 2003 will not boot after an installation of SP1 or R2 with FC Port 2.22a8. The only way to boot SP1 is to disconnect the Fibre Channel cables. If you are using FC Port 2.22a8, you should update to an SP1-supported Emulex driver prior to installing SP1. Confirm with your Emulex HBA service provider as to which Emulex driver versions have been qualified for use with SP1 and their products. If you have installed SP1 with FC Port driver version 2.22a8
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit Base driver, HBAnyware utility 3.3a14
Operating Systems
Windows 2003
Version Driver
2.00a12
Size Driver
21.4Mb
File Name
storportminiportkit_2-00a12-1d.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or SP2 and the KB932755 update to the Microsoft Storport driver are required. The KB932755 update must be applied before the Emulex Storport Miniport driver version 2.00 can be installed.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
User Manual Storport Miniport Driver Version 2.00
Operating Systems
Windows 2003
Version Manual
2.00a12
Size Manual
984Kb
File Name
manual.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or SP2 and the KB932755 update to the Microsoft Storport driver are required. The KB932755 update must be applied before the Emulex Storport Miniport driver version 2.00 can be installed.
Storport Miniport Driver Version 2.00 for Windows Server 2003 and Windows Vista

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
User Manual HBAnyware Utility Version 3.3
Operating Systems
Windows 2003
Version Manual
2.00a12
Size Manual
3.1Mb
File Name
hbanyware.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or SP2 and the KB932755 update to the Microsoft Storport driver are required. The KB932755 update must be applied before the Emulex Storport Miniport driver version 2.00 can be installed.

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2003
Version Driver
1.30a9
Size Driver
24.2Mb
File Name
storportminiportkit_1-30a9-1e.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
Base driver, HBAnyware utility 3.1a8 and lputilnt version 1.8a19 (24 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
SMI-S Provider Kit
Operating Systems
Windows 2003
Version Driver
1.30a9
Size Driver
7.1Mb
File Name
elxsmiprovider1.1.6-2.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
SMI-S HBA Provider, compliant with the SMI-S 1.1.0 specification and certified against the SNIA-CTP v1.1.0.85 suite
Pre-packaged with OpenPegasus CIMOM v2.5.1, as a turnkey SMI-S agent for ease of installation and deployment (7.18 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2003
Version Driver
1.30a9
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
Installing the driver using AutoPilot Installer (498 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2003
Version Manual
1.30a9
Size Manual
4.6Mb
File Name
manual.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Driver Kit
Operating Systems
Windows 2003
Version Driver
1.20a7
Size Driver
17.9Mb
File Name
storportminiportkit_1-20a7-1d.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note The KB916048 update to the Microsoft Storport driver is required.
Base driver, HBAnyware utility 3.0a16 and lputilnt version 1.8a19 (17.9 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
SMI-S Provider Kit
Operating Systems
Windows 2003
Version Driver
1.20a7
Size Driver
7.1Mb
File Name
elxsmiprovider1.1.6-2.exe
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note The KB916048 update to the Microsoft Storport driver is required.
SMI-S HBA Provider, compliant with the SMI-S 1.1.0 specification and certified against the SNIA-CTP v1.1.0.85 suite
Pre-packaged with OpenPegasus CIMOM v2.5.1, as a turnkey SMI-S agent for ease of installation and deployment (7.18 MB exe file)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Quick Install
Operating Systems
Windows 2003
Version Driver
1.20a7
Size Driver
115Kb
File Name
quick_installation.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or later, and the KB932755 update to the Microsoft Storport driver, are required.
Installing the driver using AutoPilot Installer (498 KB)

Introduction
AutoPilot Installer™ for Emulex® drivers provides installation options that range from a simple
installation with a few mouse clicks to custom unattended installations using predefined script files.
AutoPilot Installer is included with Emulex drivers and utilities in Windows executable files that can be
downloaded from the Emulex Web site. Run the distribution executable file to extract all of the software
needed for an installation, then complete the installation using AutoPilot Installer.
AutoPilot Installer allows you to install a driver using any of the following methods:
Hardware-first installation. The host bus adapter (HBA) is installed before the downloaded Emulex
drivers and utilities are installed. See page 3 for this procedure.
Software-first installation. This new installation method allows drivers and utilities to be downloaded
from the Emulex Web site and installed using AutoPilot Installer prior to the installation of any HBAs. The
drivers and utilities are automatically used when HBAs are installed at a later time. See page 4 for this
procedure.
Unattended installation. This new installation method allows you to set up AutoPilot Installer to run
unattended using customized scripts. Unattended installation can be used for both hardware-first and
software-first installations. See the complete Installation section of the driver user manual for more
information.

Updating the Driver Using AutoPilot Installer
If you are currently running an older driver version, use the hardware-first installation procedure to
update your driver. Begin at step 2 to update the driver.
You can also update the Emulex drivers following the manual installation method. See the complete
Installation section of the driver user manual for this procedure.

Distribution Executable File Overview
The distribution executable file is a self-extracting file that includes the following:
• AutoPilot Installer - installs driver and utilities.
• Driver - manages communication and data transfer between applications and I/O devices, using
HBAs as agents.
• HBAnyware utility - performs installation and configuration tasks on remote and local adapters.
• Driver-specific utility (elxcfg for FC Port, lputilnt for Storport Miniport and SCSIport Miniport) -
provides a user-friendly interface that allows you to examine, manage and configure local HBAs.
4. The default installation location is displayed. Browse to a different location, if desired. Click
Install to continue the installation.
5. The Progress window is displayed. As each task is completed, the corresponding checkbox is
automatically selected.
6. After all tasks are completed, a confirmation window is displayed. The Start AutoPilot Installer
checkbox is automatically selected. To start AutoPilot Installer later, clear this checkbox.
7. Click Finish to close the distribution executable file.
AutoPilot Installer Introduction
The Emulex AutoPilot Installer is a Fibre Channel HBA installation wizard for Windows. The AutoPilot
Installer installs (or updates) Emulex drivers and utilities and configures HBAs, drivers and utilities.

Prerequisites
• One of the following operating systems:
•Windows Server 2003 running on an x86, x64 or Itanium 64-bit platform.
•For the Emulex Storport Miniport driver, a Microsoft driver update may be required. See the Emulex Web site for the latest update to the Microsoft Storport driver.
•Windows 2000 Server - Service Pack 4 or later is recommended for all installations. Storport Miniport is not compatible with Windows 2000 Server.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP850
Description
Manual
Operating Systems
Windows 2003
Version Manual
1.20a7
Size Manual
3.6Mb
File Name
storport120manual.pdf
Information
Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note The KB916048 update to the Microsoft Storport driver is required.
Installation, Configuration and Troubleshooting (3,264 KB)

Introduction.............................................................................................................. 1
Important Considerations......................................................................................... 2
Changing Driver Types...................................................................................... 2
Microsoft Storport Driver Update ....................................................................... 2
Updating the Storport Miniport Driver Using AutoPilot Installer.......................... 2
Definitions................................................................................................................ 2
Storport Miniport Driver Information ......................................................................... 3
Prerequisites ..................................................................................................... 3
Compatibility...................................................................................................... 3
New in This Release ......................................................................................... 3
Known Issues .................................................................................................... 3
Files Included in this AutoPilot Installer ............................................................. 4
Distribution Executable File Overview ..................................................................... 5
Running the Distribution Executable File ........................................................... 5
AutoPilot Installer..................................................................................................... 6
Introduction ....................................................................................................... 6
Prerequisites ............................................................................................... 6
AutoPilot Installer Features ......................................................................... 6
Configuration Questions.............................................................................. 6
Installation Planning .......................................................................................... 6
AutoPilot Installation Procedures ............................................................................. 7
Hardware-First Installation................................................................................. 7
If the Installation Fails ................................................................................. 8
Software-First Installation .................................................................................. 8
Installing the HBAnyware Security Configurator ...................................................... 9
Unattended Installation .......................................................................................... 10
AutoPilot Configuration File Format................................................................. 10
Mandatory Configuration File Changes ........................................................... 10
Deleting Questions in the APInstall.cfg File ..................................................... 11
Optional Configuration File Changes............................................................... 11
Setting Up Driver Parameters.......................................................................... 14
Setting Up System Parameters ....................................................................... 14
Unattended Error Codes Reference Table....................................................... 14
Invoking AutoPilot Installer .............................................................................. 15
Batch File Example ......................................................................................... 15
Manually Installing or Updating the Storport Miniport Driver .................................. 17
Overview ......................................................................................................... 17
Removing the Adjunct Driver Registry Key...................................................... 17
Manually Installing the Emulex PLUS (ElxPlus) Driver .................................... 17
Manually Updating the Emulex PLUS (ElxPlus) Driver .................................... 18
Manually Installing or Updating the Storport Miniport Driver ............................ 19
Manually Installing the Driver Utilities .............................................................. 20
Uninstalling the Utility Package ....................................................................... 20
Uninstalling the Emulex Drivers....................................................................... 22
Configuration ...........................................................................................................23
Introduction............................................................................................................ 23
Starting HBAnyware from the Desktop ............................................................ 24
HelpDrivers Since March 2000