Emulex LP1005DC Download Drivers, Manual, Firmware and BIOS

Available 15 files for LP1005DC
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
x86 BootBIOS
Operating Systems
Boot Code
Version BIOS
2.02a2
Size BIOS
56Kb
File Name
mc501a3.zip
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA
Contains: x86 BootBIOS version 1.70a3 and OpenBoot version 1.50a3.
Support: HS20, HS40, JS20, LS20 This Combined Boot version 5.01a3 contains:

(1) x86 BootBIOS version 1.70a3
(2) OpenBoot version 1.50a3

For detailed information about x86 BootBIOS, please refer to section II below,
and for OpenBoot, section III. This Combined Boot can boot on either Intel
x86 Platform or Non-Intel Fcode. In other words, the platform is transparent
and the user should not be concerned with any differences with regard to x86
BootBIOS or OpenBoot.

Combined Boot is a complete image, whenever it is enabled by any Emulex OS
utility, the whole image (x86 BootBIOS and OpenBoot) is enabled. This
is also true for disable.

This boot code is a special build for the LP1005DC product only.
DO NOT download it to any other Emulex product.
Files included in this release:

\readme.txt the file you are reading
\MC501A3.PRG LP1005DC Combined Boot
Combined Boot Load Procedure

The Light Pulse Combined Boot is distributed as a .PRG file. This file may be
downloaded to the Adapter using the firmware upgrade procedure with the following
Utility in Various systems.

1. LP6DUTIL.EXE : DOS based utility.

Please refer to the utility user manual for details on using the above tool.

2. LPUTILNT : Windows Miniport Driver.

Please refer to the utility user manual for details on using the above tool.

3. Emulex Configuration Tool : Windows Port Driver.

Please refer to the elxcfg user manual for details on using the above tool.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Boot Code User Manual
Operating Systems
Boot Code
Size Manual
4.9Mb
File Name
bootcode.pdf
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA Introduction..............................................................................................................1
Emulex Boot Code Files....................................................................................1
Boot from SAN.........................................................................................................2
Windows Server 2008 and Windows Server 2003.............................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (x86 and x64)..........................................................2
Configure Boot from SAN on Windows Server 2008 and Windows Server 2003 (Itanium)..................................................................3
New Installation of Windows 2008 UEFI- Aware Operating System
on a UEFI-based x64 Server.................................................................3
Direct a UEFI-Based Server to a Windows Server 2008 OS Image (Installed as UEFI-Aware) Already Installed on the SAN.......................4
The GUID Partition Table......................................................................4
Install Windows Server 2008 on an FC Boot Disk (x86, x64 and Itanium)...5
Install Windows Server 2003 on an FC Boot Disk (x86, and x64
and Itanium)................................................................................................6
Linux and VMware.............................................................................................7
Configure Boot from SAN on Linux or VMware (x86 and x64).....................7
Configure Boot from SAN on Linux (PowerPC)...........................................7
Configure Boot from SAN on Linux (Itanium)..............................................7
Solaris...............................................................................................................8
Configure Boot from SAN on Solaris SFS (x86 and x64)............................8
Determine LUNs to Select for Boot from SAN.......................................8
Configure Boot from SAN on Solaris SFS (SPARC)....................................8
Configure Boot from SAN on Solaris LPFC (SPARC)..................................9
Install Solaris from a Network Image..................................................10
Install Solaris by Migrating an Image from a Local SCSI Disk.............11
Install, Update and Enable Boot Code...................................................................14
BIOS Utility............................................................................................................15
Start the BIOS Utility.................................................................................15
Enable an Adapter to Boot from SAN........................................................17
Configure Boot Devices...................................................................................17
Configure Adapter Parameters........................................................................21
Change the Default AL_PA (Arbitrated Loop Physical Address)................22
Change the PLOGI Retry Timer................................................................23
Change Topology......................................................................................24
Enable or Disable the Spinup Delay..........................................................25
Set Auto Scan...........................................................................................26
Enable or Disable EDD 3.0.......................................................................27
Enable or Disable the Start Unit Command...............................................28
Enable or Disable the Environment Variable.............................................29
Enable or Disable Auto Boot Sector..........................................................30
Change Link Speed...................................................................................31
Reset to Default Values.............................................................................32
Use Multi-Path Boot from SAN..................................................................33
OpenBoot..............................................................................................................34
Attribute Commands.................................................................................34
Functional Commands..............................................................................35
EFIBoot.................................................................................................................37
Install the EFI Utility..................................................................................37
Start the EFI Utility....................................................................................38
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Firmware
Operating Systems
Firmware
Version Firmware
1.92a1
Size Firmware
332Kb
File Name
mf192a1-2.zip
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA
Support: HS20, HS40, JS20, LS20 Compatibility:

This kit supports the LP1005DC-CM2 host adapter.

This kit includes the following files:

README.TXT The file you are reading

MF192A1.ALL All firmware components, no boot code

LP6DUTIL.EXE DOS-based diagnostic utility 9.3a6
LP6DUTIL.DOC LP6DUTIL diagnostic utility document
SAMPLESCRIPT.TXT An example script for LP6DUTIL 9.3a6
Changes and Corrections:

-- Changes and corrections between 1.92a1 and 1.91a5:

Implemeted beaconing feature for Pegasus and Thor. (CR 16592, 21846)

The R_A_TOV field is now properly expressed in milliseconds. (CR 22640)

Improved target mode "fast" POST so that power up no longer causes HBA
to hang. (CR 22594)

A timeout is prevented by allowing the firmware to process fatal DMA
engine errors even if the DMA is not complete, such as during a PCI
master abort. (CR 22641)

Various concurrent FLASH programming issues were resolved by improving
the FLASH interlocking/unlocking algorithm, implementing Intel errata,
and implementing erase failure recovery code.
(CR 21885, 21888, 21889, 21890)

We now default to allowing the PCI bridge to reorder data frames as
necessary, which may result in a system performance increase for some
systems. (CR 21867)

Improved FCP2 recovery to avoid the dropping of frames
(and the resulting delays) during REC ELS command. (CR 21865)

Fixed a recovery issue where a corrupted REC frame with a mismatching
offset would cause the HBA to loop, continually requesting recovery.
(CR 21864)

To avoid dropped receive frames in the case where an OXID is reused
for a new exchange during the ABTS/RRQ processing window, we now skip
any matching "new" exchanges which are in the RRQ state. (CR 21855)

Improved management of unavailable memory by limiting the number of
retries. The HBA now reports an error attention after retries have
been exhausted. (CR 21854)

Improved DMA error handling of split errors where host memory has been
made unavailable. (CR 21853)

Commands are now timed out properly when in FCP-2 mode. (CR 21852)

Protocol testing with invalid conditions revealed protocol response
errors which have had no reported instances of failure in the field.
(CR 21850, 21851, 21863)

An I/O timeout during tape operation was eliminated by delaying
processing of any FCP2 errors during discovery. (CR 17363)

Thor no longer deadlocks during processing of RRQ when RESET_RING is
issued with no available exchange resources. (CR 20064)

Improved operation of Pegasus Rx DMA firmware on PCI-X bus.
(CR 21542)
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Firmware Update Manual
Operating Systems
Firmware
Size Firmware
106Kb
File Name
fwupdate.pdf
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA Introduction.............................................................................................................. 1
Prerequisites ..................................................................................................... 1
Things to Know Before You Download ............................................................. 1
Update Utilities ........................................................................................................ 2

Introduction
For information about any firmware release, see the release notes on the Emulex Web site. Release
notes include information such as new features, compatibility, known issues and resolved known issues.
This manual does not contain the procedures themselves. It serves as a guide to the publication that
contains the procedures you need.

Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and the swap
slice of the current local boot disk.

Things to Know Before You Download
• Before you download the OneConnect or LightPulse files, create a directory for them.
• As a measure of protection, ensure that critical files on your local boot disk are backed up.
• Firmware may be bundled with boot code. Boot code allows you to designate a device that is
attached to the adapter as a boot drive. If you select a firmware image that includes boot code,
the update procedure will load both the new firmware and the boot code at the same time. After
updating, refer to the Emulex Boot Manual for procedures on enabling the boot code on your
adapter.
• Emulex firmware files support both OneConnect and LightPulse adapters.
• For OneConnect adapters:
• Firmware and boot code are provided in a single flash image called a .UFI file.
• The UFI file contains all of the files that support all OneConnect adapters. The latest
files for your adapter are installed automatically when you use an Emulex utility to
update the firmware.
• The UFI file contains both firmware and boot code.
• For LightPulse adapters:
• Firmware is provided in a .ZIP file as a .ALL file or a .AWC file. You must manually unzip
the .ALL or .AWC file from the .ZIP file before you can use an Emulex utility to install it.
• Firmware differs between adapter models. Make sure you download the appropriate
firmware for your adapter.
• The .ZIP file may or may not include a boot code (.PRG) file.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Installation Manual
Operating Systems
Manual
Size Manual
156Kb
File Name
install.pdf
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA Table of Contents
Installation
Compatibility/Prerequisites
Set Jumpers
Install HBA
Attach Media
Apply Power
View LEDs
Reference
Specifications
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety

Prerequisites
· Host computer must provide 3.3 VDC bus power
One open 32-bit or 64-bit (64-bit recommended) PCI or PCI-X bus
slot.
·
· PCI bus clock rate of 33 MHz or 66 MHz
· PCI-X bus clock rate of 66 MHz, 100 MHz, or 133 MHz
· Media and connectors

Record IEEE and serial numbers.
Each host bus adapter is shipped with a unique 64-bit identifier called
the IEEE address. The Fibre Channel industry uses a World Wide
Name (WWN) derived from the IEEE address, and this number is
needed for Fibre Chanel connectivity. The serial number is used when
communicating with Emulex. Both numbers are clearly marked on the
board. We recommend that you record these numbers before
installation.
Turn off and unplug the computer.
Remove the computer case.
Remove the blank panel from an empty 32- or 64-bit PCI or PCI-X
bus slot. Compare the removed panel to the bracket on the host bus
adapter. Follow steps 5-8 to change the bracket if they are different
sizes.

Note The host bus adapter comes with a standard PCI
bracket installed. The low-profile mounting bracket
is shorter than the standard bracket; approximately
3.11 in. (7.9cm) compared to 4.75 in. (12.06 cm)
long.

Remove the mounting bracket screws from the top of the host bus
adapter.
Remove the bracket and store it for future use.
Align the new mounting bracket tabs with the holes in the HBA.

Note Be careful not to push the bracket past
the transceiver housing's grounding tabs.

Replace the screws that attach the HBA to the bracket.
Insert the host bus adapter into the empty 32- or 64-bit PCI or PCI-X
bus slot. Press firmly until it is seated.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Troubleshooting Manual
Operating Systems
Manual
Size Manual
649Kb
File Name
troubleshooting.pdf
Information
Bus Type PCI-X 1.0
Max Bus Speed 133 MHz
Product Type HBA Overview................................................................................................................ 1
Be Informed, Stay Informed, Stay Current 1
The Importance of Compatibility, Driver Updates and Firmware Updates 1
Driver Updates........................................................................................... 1
Firmware Updates...................................................................................... 2
Emulex Configuration Parameters 3
How Emulex Device Driver Configuration Parameters Work...................... 3
Emulex Applications 3
Troubleshooting...................................................................................................... 4
Observing the Problem 4
Isolating the Problem 4
SAN Components...................................................................................... 4
Server Components................................................................................... 5
Checklists 6
Connectivity Checklist................................................................................ 6
Installation Checklist.................................................................................. 7
Upgrade Checklist...................................................................................... 8
Configuration Checklist.............................................................................. 8
Tools to Collect Data 9
Driver Tools - Event Logging...................................................................... 9
The OneCommand Manager and HBAnyware Applications....................... 9
Other Ways to Collect Data...................................................................... 10
Common Problems 10
Hardware Issues...................................................................................... 10
Link Down................................................................................................ 10
Cannot See Devices or Drives................................................................. 11
Out-of-Date Driver Version....................................................................... 12
Out-of-Date Firmware Version.................................................................. 12
OneConnect and LightPulse LP21000 Adapters 13
OneConnect and LP21000 Checklist....................................................... 13
OneConnect and LP21000 Symptoms..................................................... 13
When to Contact Emulex...................................................................................... 14
Emulex Web Site and Emulex Support................................................................. 15
Emulex Support Page 15
Contact Emulex After Hours, Weekends or Holidays............................... 17
LED Reference Information.................................................................................. 18
Firmware Operation and Port Activity LEDs 18
Common LED States 18
Normal Link Up........................................................................................ 18
Link-Down or adapter waiting................................................................... 19
Heart-beat indication................................................................................ 19
OneConnect CNA LEDs........................................................................... 19
LP21000 LEDs......................................................................................... 19
LED Table................................................................................................ 21

Driver Updates
To update your driver, download the latest Emulex driver and utilities from the Emulex Web site. From
the main Emulex Web site, click Downloads, click your vendor and then click the link for your operating
system (OS).
Drivers for Windows
• The drivers for Windows include support for Windows Server 2008 R2, Windows Server 2008,
Windows Server 2003, Windows 2000 Server and Windows NT (No future versions of drivers for
Windows 2000 Server or Windows NT are planned.)
•The driver kit download includes the base driver and the OneCommand Manager application.
•If you are running Windows Server 2008 R2, Windows Server 2008, Windows Server 2003 or Windows 2000 Server, the driver kit download includes AutoPilot Installer®, which enables you to quickly install or update drivers and utilities and configure adapters, drivers and utilities.
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Driver Kit
Operating Systems
NetWare 5.1, 6.0 and 6.5
Version Driver
2.21d
Size Driver
65Kb
File Name
nw221d.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.21d August 10, 2006
This Readme file contains the description of the 2.21d version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 5 (NW65SP5)
- NetWare 6.0 with Support Pack 5 (NW6SP5 )
- NetWare 5.1 with Support Pack 8 (NW51SP8)
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LPe111 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Manual
Operating Systems
NetWare 5.1, 6.0 and 6.5
Version Manual
2.21d
Size Manual
484Kb
File Name
manual.pdf
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.21d August 10, 2006
This Readme file contains the description of the 2.21d version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 5.1, 6.0 and 6.5. It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 5 (NW65SP5)
- NetWare 6.0 with Support Pack 5 (NW6SP5 )
- NetWare 5.1 with Support Pack 8 (NW51SP8)
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LPe111 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".

5. Select "Select an additional driver".

6. Press to install a driver not on the list.
(If there is a previously installed version of the driver,
this will update and replace it).
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Driver Kit
Operating Systems
NetWare 6.5
Version Driver
2.22a
Size Driver
66Kb
File Name
nw222a-1c.zip
Information
Emulex LightPulse PCI Fibre Channel Adapter
for Novell Netware 5.1, 6.0, and 6.5

Emulex Corporation

Release 2.22a January 24, 2008
This Readme file contains the description of the 2.22a version
of the LPFC.HAM driver for the Emulex LightPulse adapter family
and Novell NetWare 6.5 (and is compatible with 5.1 and 6.0, though
there is no official support). It provides support for
switched Fabric operation and multi-initiator environments and
for up to 16 adapter channels using single or dual channel HBAs.

The Emulex LPFC.HAM driver has been tested in the following
environments:

1. OS Versions:
- Netware 6.5 with Support Pack 7 (NW65SP7)
- NetWare 6.0 is not supported at this time; use at own risk and NW60SP6
- NetWare 5.1 is not supported at this time; use at own risk and NW51SP8
- NetWare 4.2 is not supported at this time; use Emulex driver version 1.23c
to support NetWare 4.2.
2. Arbitrated Loop Environment
3. Switched Fabric Environment
4. Emulex Fibre Channel adapters
- LPe12000 series adapters (minimum firmware revision 1.00a9)
- LPe1250 series adapters (minimum firmware revision 1.00a9)
- LPe121 series adapters (minimum firmware revision 1.00a9)
- LP11000 series adapters (minimum firmware revision 1.91a1)
- LP1150 series adapters (minimum firmware revision 1.91a1)
- LPe11000 series adapters (minimum firmware revision 1.91a1)
- LPe1150 series adapters (minimum firmware revision 1.91a1)
- LPe111 series adapters (minimum firmware revision 1.91a1)
- LP10000 series adapters (minimum firmware revision 1.91a1)
- LP1050 series adapters (minimum firmware revision 1.91a1)
- LP101 series adapters (minimum firmware revision 1.82a0)
- LP9802DC, LP9802 and LP982 (minimum firmware version 1.91a1)
- LP9402DC, LP9002L, LP9002DC, LP9000 or LP952L (recommended firmware version 3.92a2)
- LP8000, LP8000DC and LP850
-- If your HBA has a Dragonfly chip version 2.00 or greater
use firmware version 3.92a2.
-- If your HBA has a Dragonfly chip below version 2.00,
use firmware version 3.30a7.
- LP7000E (minimum firmware version 3.21a0)
5. Suitable target hardware; lpfc.ham complies with SAN protocols
for switched fabrics and arbitrated loops.

This release includes the following files:

1. LPFC.HAM - Emulex Fibre Channel adapter HAM driver
2. lpfc.ddi - driver description file
3. readme.txt - readme file (this file)
INSTALLATION INSTRUCTIONS ON AN EXISTING NETWARE SERVER:

1. The server must support PCI 2.2 standard slots or PCI-X 1.1
standard slots.

2. At the server console load the install program. On
Netware 6.5 enter

LOAD HDETECT

On Netware 6.0, 5.1, or 5.0, enter

LOAD NWCONFIG

3. Select "Driver Options".

4. Select "Configure disk and storage device drivers".
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Manual
Operating Systems
NetWare 6.5
Version Manual
2.22a
Size Manual
499Kb
File Name
manual.pdf
Information
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Applications Kit
Operating Systems
VMware
Version Driver
lpfcutil-7.1.14
Size Driver
105Kb
File Name
lpfcutil-7.1.14.tgz
Information
Lputil version 1.6a10, HBA API library version 2.0.f; Virtual Infrastructure 3 (ESX 3.0.2, Virtual Center 2.0.2) - Alternate driver and Microsoft Cluster Software , 2 GBit/s HBAs (7.1.14_vmw2); Virtual Infrastructure 3 (ESX 3.0.1, Virtual Center 2.0.1) - Microsoft Cluster Software, 2 Gb/s HBAs (7.1.14_vmw1); Virtual Infrastructure 3 (ESX 3.0, Virtual Center 2.0) - 2 Gb/s HBAs (7.1.14_vmw1)

This kit has been designed for the following environment:

- Supported Hardware architecture platforms:
- 32-bit Intel platforms
- 64-bit Intel platforms

- Supported Linux OS:

- Red Hat Enterprise Linux AS 2.1
- Red Hat Enterprise Linux AS 3.0
- SuSE SLES 8
Please refer to Emulex Website (www.emulex.com) for an update and accurate
list of kernel versions.

- Supported Emulex enterprise adapters:
- LP10000DC
- LP10000
- LP1050DC
- LP1050
- LP9802DC
- LP9802
- LP982
- LP9402DC
- LP9002DC
- LP9002L
- LP9000
- LP952L
- LP8000DC
- LP8000


************************************************************************
This Application kit has been designed to work only with the Open Source
Linux Driver Kit, Version 7.1.14.

It includes lputil version 1.6a10.

Installation:
After you unpack this tarball, type ./Install.sh. This will install
the Emulex applications and libraries.

Removal:
To remove the Emulex applications, libraries and base HBAAPI library,
type ./Remove.sh.
************************************************************************

dfc Diagnostic utility for driver debug
libdfc.a Diagnostic utility library interface
libHBAAPI.so Library to support HBAAPI standard
libemulexhbaapi.so Library to support HBAAPI standard
lputil Diagnostic utility for adapter maitenance
Install.sh Installation script
Remove.sh Removal script
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Applications Kit
Operating Systems
VMware
Version Driver
lpfcutil-7.3.2
Size Driver
113Kb
File Name
lpfcutil-7.3.2.tgz
Information
Lputil version 2.0a12, HBA API library version 2.0.f; Virtual Infrastructure 3 (ESX 3.0.1, Virtual Center 2.0.1) - 2 & 4 Gb/s HBAs (7.3.2_vmw2); Virtual Infrastructure 3 (ESX 3.0, Virtual Center 2.0) - 4 Gb/s HBAs (7.3.2_vmw1); ESX 2.5.5 - 2 & 4 Gb/s HBAs (7.3.2_vmw4); ESX 2.5.4 Driver Disk - 4 Gb/s HBAs (7.3.2_vmw3)

This kit has been designed for the following environment:

- Supported Hardware architecture platforms:
- 32-bit Intel platforms
- 64-bit Intel platforms

- Supported Linux OS:

- Red Hat Enterprise Linux AS 2.1
- Red Hat Enterprise Linux AS 3.0
- SuSE SLES 8
Please refer to Emulex Website (www.emulex.com) for an update and accurate
list of kernel versions.

- Supported Emulex enterprise adapters:
- LP10000DC
- LP10000
- LP1050DC
- LP1050
- LP9802DC
- LP9802
- LP982
- LP9402DC
- LP9002DC
- LP9002L
- LP9000
- LP952L
- LP8000DC
- LP8000


************************************************************************
This Application kit has been designed to work only with the Open Source
Linux Driver Kit, Version 7.3.2.

It includes lputil version 2.0a12.

Installation:
After you unpack this tarball, type ./Install.sh. This will install
the Emulex applications and libraries.

Removal:
To remove the Emulex applications, libraries and base HBAAPI library,
type ./Remove.sh.
************************************************************************

dfc Diagnostic utility for driver debug
libdfc.a Diagnostic utility library interface
libdfc.so Diagnostic utility library interface
libHBAAPI.so Library to support HBAAPI standard
libemulexhbaapi.so Library to support HBAAPI standard
lputil Diagnostic utility for adapter maitenance
Install.sh Installation script
Remove.sh Removal script
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Applications Kit
Operating Systems
VMware
Version Driver
lpfcutil-2.01g
Size Driver
107Kb
File Name
lpfcutil-2.01g-2.tgz
Information
Lputil version 1.6a6, HBA API library version 2.0f; ESX 2.5.4 (2.01g_vmw2, also alternate for ESX 2.5.5); ESX 2.5.3 (2.01g_vmw1); ESX 2.5.0, ESX 2.5.1 and ESX 2.5.2 (2.01g)

This Application kit has been designed for the following environment:

- Supported Hardware architecture platforms:
- 32-bit Intel platforms (IA-32)
- 64-bit Intel platforms (IA-64)
- Power PC 64 bits (PPC)

- Supported Linux OS:

- Red Hat Enterprise Linux AS 2.1
- Red Hat Enterprise Linux AS 3.0
- SuSE SLES 8 ppc64
Please refer to Emulex Website (www.emulex.com) for an update and accurate
list of kernel versions.

- Supported Emulex enterprise adapters:
- LP10000DC
- LP10000
- LP1050DC
- LP1050
- LP9802DC
- LP9802
- LP982
- LP9402DC
- LP9002DC
- LP9002L
- LP9000
- LP952L
- LP8000DC
- LP8000


************************************************************************
This Application kit has been designed to work only with the Open Source
Linux Driver Kit, Version 2.01g, and HBAAPI version 2.0f.

It includes lputil version 1.6a6.

Installation:
After you unpack this tarball, type ./Install.sh. This will install
the Emulex applications and libraries.

Removal:
To remove the Emulex applications, libraries and base HBAAPI library,
type ./Remove.sh.
************************************************************************

dfc Diagnostic utility for driver debug
libdfc.a Diagnostic utility library interface
libHBAAPI.so Library to support HBAAPI standard
libemulexhbaapi.so Library to support HBAAPI standard
lputil Diagnostic utility for adapter maitenance
Install.sh Installation script
Remove.sh Removal script
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Applications Kit
Operating Systems
VMware
Version Driver
lpfcutil-1.22e
Size Driver
120Kb
File Name
lpfcutil-1.22e.tgz
Information
Lputil version 1.5a0, HBA API library version 2.0b; alternate driver for ESX 2.0, ESX 2.0.1, ESX 2.1, ESX 2.1.1 and ESX 2.1.2

This Application kit has been designed for the following environment:

- Supported Hardware architecture platforms:
- 32-bit Intel platforms (IA-32)
- 64-bit Intel platforms (IA-64)
- Power PC 64 bits (PPC)

- Supported Linux OS (note that testing has been conducted only with the kernels in parenthesis):

- Red Hat Pro 7.3 (kernel 2.4.18-27)
- Red Hat Pro 8.0 (kernel 2.4.18-27)
- Red Hat Advanced Server 2.1 x86 (kernel 2.4.9-e.16)
- SLES 7 x86 (kernel 2.4.16)
- SLES 8 x86 (kernel 2.4.19)
- Red Hat Advanced Server 2.1 IA-64 (kernel 2.4.18-e.25)
- SuSE 8.0 ppc64 (kernel 2.4.19-u11-ppc64)

- Supported Emulex enterprise adapters:
- LP8000
- LP9000
- LP9002L
- LP9002DC
- LP9402DC
- LP9802
- LP10000

************************************************************************
This Application kit has been designed to work only with the Open Source
Linux Driver Kit, Version 1.22e.

It includes lputil version 1.4a8

Installation:
After you unpack this tarball, type ./Install.sh. This will install
the Emulex applications and libraries.

Removal:
To remove the Emulex applications, libraries and base HBAAPI library,
type ./Remove.sh.
************************************************************************

dfc Diagnostic utility for driver debug
fcdiag.h Diagnostic utility library header file
libdfc.a Diagnostic utility library interface
libHBAAPI.so Library to support HBAAPI standard
libemulexhbaapi.so Library to support HBAAPI standard
lputil Diagnostic utility for adapter maitenance
Install.sh Installation script
Remove.sh Removal script

The following section details the LINUX md5sum (128 bit checksum) results
for the current release contents:

For I386:

57216ef4164549da6cbf552df6f5773d dfc
9b88355a3c1a311306a8579ff4b46c2d fcdiag.h
7b429052c5054f7caca26cc6e7ab8818 libHBAAPI.so
04f44bcfc7aa63f57abba85ecdd9a14e libdfc.a
1968b9a74ba82e5c42242ae0279ceb39 libemulexhbaapi.so
aa43ddcfb9f7c9f5a4063652e69d0a7b lputil
Company
Emulex
Categories
Networks Cards
Model
Emulex LP1005DC
Description
Applications Kit
Operating Systems
VMware
Version Driver
lpfcutil-4.20q
Size Driver
127Kb
File Name
lpfcutil-4.20q.tgz
Information
Lputil version 1.4a8, HBA API library version 1.3; ESX 2.0, ESX 2.0.1, ESX 2.1, ESX 2.1.1 and ESX 2.1.2 (also alternate driver for ESX 2.5.0, ESX 2.5.1 and ESX 2.5.3)

This Application kit has been designed for the following environment:

- Supported Hardware architecture platforms:
- 32-bit Intel platforms (IA-32)
- 64-bit Intel platforms (IA-64)
- Power PC 64 bits (PPC)

- Supported Linux OS (note that testing has been conducted only with the kernels in parenthesis):

- Red Hat Pro 7.3 (kernel 2.4.18-27)
- Red Hat Pro 8.0 (kernel 2.4.18-27)
- Red Hat Advanced Server 2.1 x86 (kernel 2.4.9-e.16)
- SLES 7 x86 (kernel 2.4.16)
- SLES 8 x86 (kernel 2.4.19)
- Red Hat Advanced Server 2.1 IA-64 (kernel 2.4.18-e.25)
- SuSE 8.0 ppc64 (kernel 2.4.19-u11-ppc64)

- Supported Emulex enterprise adapters:
- LP8000
- LP9000
- LP9002L
- LP9002DC
- LP9402DC
- LP9802
- LP10000

************************************************************************
This Application kit has been designed to work only with the Open Source
Linux Driver Kit, Version 4.20q.

Installation:
After you unpack this tarball, type ./Install.sh. This will install
the Emulex applications and libraries.

Removal:
To remove the Emulex applications, libraries and base HBAAPI library,
type ./Remove.sh.
************************************************************************

dfc Diagnostic utility for driver debug
fcdiag.h Diagnostic utility library header file
libdfc.a Diagnostic utility library interface
libHBAAPI.so Library to support HBAAPI standard
libemulexhbaapi.so Library to support HBAAPI standard
lputil Diagnostic utility for adapter maitenance
Install.sh Installation script
Remove.sh Removal script
The following section details the LINUX md5sum (128 bit checksum) results
for the current release contents:

db2ebdcdf2d3fde90feb0c3024e56808 ./dfc
327385b6a6e0df6965cd0a66fba45190 ./fcdiag.h
f5a8c90c7446c051c78c79649fc0289d ./libdfc.a
5a45829a47b00df673de2a8410036a9f ./lputil
743c00a91536b13fbfe11bd4326eb0ba ./libHBAAPI.so
ad015c6f292b893167e2467cf2b7bcd6 ./libemulexhbaapi.so
HelpDrivers Since March 2000