Emulex 30p-35p HP 2Gb-s Mezz Card Networks Cards > Downloads Drivers, Utilities, Manual, Firmware and BIOS

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

x86 BootBIOS

Operating System

Boot Code

Version

1.71a0

Size Driver

33KB

File Name

mb171a0.zip

Observations

BootBIOS for x86 platforms and x64 platforms that support legacy BIOS. The current BIOS provides x86 boot capability through the use of INT13 system
BIOS calls. The BIOS supports:

(1) Multi-topology: Fabric Point to Point; FC-AL: Private loop and Public loop
(2) Multi-initiators: Up to 64 adapters in a system
(3) Multi-LUNs: Up to 256 LUNs
(4) Multi-boot: Complies with the BIOS Boot Specification (BBS).
(5) EDD (Enhanced Disk Drive Services): Supports both EDD 3.0 and EDD 2.1
depending selection in BIOS Utility.
(6) Boot fail over feature: There are eight boot entries that can be configured.
If the first boot entry fails the system is still able to boot from the
second configured boot entry and so on.
\B171A0.txt this file you are reading

\DB171a0.PRG Lp8000 BIOS version 1.71a0
\CB171a0.PRG LP9000 BIOS version 1.71a0
\HB171a0.PRG LP9802 BIOS version 1.71a0
\TB171a0.PRG LP10000 BIOS version 1.71a0
\BB171a0.PRG LP11000 BIOS version 1.71a0
\ZB171a0.PRG LPe11000 BIOS version 1.71a0

\QB171a0.PRG Lp850 BIOS version 1.71a0
\RB171a0.PRG LP950 BIOS version 1.71a0
\LB171a0.PRG LP982 BIOS version 1.71a0
\MB171a0.PRG LP1050 BIOS version 1.71a0
\JB171a0.PRG LP1150 BIOS version 1.71a0
\YB171a0.PRG LPe111 BIOS version 1.71a0
\EB171a0.PRG LP101 BIOS version 1.71a0
\WB171a0.PRG LPe1150 BIOS version 1.71a0
***** Important Note ******

(1) BIOS downloading

This version of BIOS image has increased size from 44K to 48K. As a result, it might
fail during the downloading of the BIOS .prg file. One way to correct the problem
is to download the firmware .AWC file WITHOUT the BIOS image
(for example: dd390a7.awc). Then, download the BIOS .prg file.
(2) BIOS was not activated (Enabled)

If the adapter BIOS is not activated (enabled) by LP6dutil or other O.S. utility,
this adapter would not be configured. Also, there is "No BIOS support" message next
to this adapter in BIOS Utility. User must use LP6dutil or other O.S. Utility to
activate (enable) the BIOS in order to make this card bootable.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Linux Offline Utility (requires driver version 8.2.0.29 or later)

Operating System

Linux

Version

1.0a11

Size Driver

2.8MB

File Name

linlpcfg-1.0a11.tgz

Observations

Please note: EMC qualifies operation of the hardware, drivers, firmware and Boot Bios for the products referenced, as documented in the current EMC ESM (EMC Support Matrix). Utility software, including HBAnyware and various stand alone utilities used to manage or maintain Emulex products, are not tested by EMC. Utility software is provided for the convenience of EMC customers. Emulex is responsible for the integrity, functionality and support.
WARNING: You are about to download the EMC Approved HBA driver. This driver is optimized for use with EMC "-E" HBAs. It is being made available to you to update your approved EMC HBAs to support your EMC and non-EMC hardware environments. Downloading this EMC approved driver for use with an unqualified or unsupported HBA may be inconsistent with applicable terms and conditions. If you have any questions about the suitability of downloading this driver, contact your Emulex or EMC sales team.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Linux Offline Utility (requires driver version 8.0.16.44 or later)

Operating System

Linux

Version

1.0a14

Size Driver

2.8MB

File Name

linlpcfg-1.0a14.tgz

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

IOCTL Application helper module

Operating System

Linux 2.6 Kernel

Version

8.0.16.18

Size Driver

201KB

File Name

lpfc_2.6_ioctl_module_kit-2.0.9-2.tar.gz

Observations

RHEL4 Update 3 x86 (Intel), x86-64 (AMD and Intel) and IA64
Tar file containing install script and scripted source RPM to build and install the IOCTL application helper module. This is needed with the RHEL 4 Update 3 distribution (which contains the 8.0.16.18 driver). This driver allows applications to communicate with the 8.0.16.18 driver.

1. System Requirements
2. Installation Process
3. Release Notes
3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

----------------------------------------------------------------------

1. System Requirements

The following distribution of Linux is supported by the Emulex
LPFC Application Helper Module:

Red Hat Enterprise Linux 4 Update 3

This Emulex LPFC Application Helper Module will function with the
Emulex LPFC driver that ships with this distribution of Linux.
Other versions of the LPFC driver will not function properly with
this version of the Application Helper Module.

2. Installation Process

The ioctl-install script can be used to install and uninstall the
LPFC Application Helper Module RPM. This RPM installs the module
sources to the /usr/src/lpfcdfc directory, builds the module for
the currently running kernel, and then installs the module to the
proper directory for the currently running kernel.

Once the RPM is installed, the 'elxlpfc' init script is installed
and configured to start and stop the 'lpfcdfc' driver during system
startup and shutdown.

For usage information, please execute the command:

./ioctl-install --help

3. Release Notes

3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the "Development Tools"
package in the software development environment and the kernel
development package with the same version as the currently running
kernel must be installed for the Application Helper Module build to
succeed.

The name of the kernel development package depends upon the name of
the kernel for which the Application Helper Module will be
installed. For example, a system with the 2.6.9-11.EL kernel
would need the kernel-devel-2.6.9-11.EL package, and a system
with the 2.6.9-11.ELsmp kernel would need the
kernel-smp-devel-2.6.9-11.EL package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

RPM Format Driver Kit

Operating System

Linux 2.6 Kernel

Version

7.1.14

Size Driver

296KB

File Name

lpfc_2.4_driver_kit-7.1.14-4.tar.gz

Observations

RHEL 3.0 Update 5 x86 (Intel), x86-64 (AMD and Intel) and x64 (Intel); Asianux 1.0 and SP1.
This kit includes the gz file containing an install script and 2 scripted source RPMs. (296 KB).

1. System Requirements
2. Description of Changes
3. Driver Installation
4. Driver Uninstallation
5. Errata

----------------------------------------------------------------------

1. System Requirements

The Emulex LPFC driver and LPFC DFC driver RPMs require gcc compiler
tools and the kernel sources for the running kernel be installed on
the system in order for the RPM installation to succeed. The following
distributions of Linux are supported by the Emulex drivers:

Red Hat Enterprise Linux 3
Red Hat Enterprise Linux 2.1
SuSE Linux Enterprise Server 8 with Service Pack 3

2. Description of Changes

The lpfc-install script installs both the LPFC driver and the LPFC
DFC driver RPMs. These RPMs install their driver sources to the
/usr/src/lpfc directory, build their drivers for the currently
running kernel, and then install the drivers to the proper
directory for the currently running kernel.

Once the RPMs are installed, the lpfc-install script creates a new
ramdisk for the currently running kernel so that the 'lpfc' driver
is loaded when the kernel is initialized during system startup.
The 'elxlpfc' init script is also installed and configured to start
and stop the 'lpfcdfc' driver during system startup and shutdown.

3. Driver Installation

Please refer to the LPFC Linux 7.1 documentation on the Emulex
website at http://www.emulex.com for an installation manual that
includes a complete set of options for the lpfc-install program.

Emulex strongly recommends uninstalling any old LPFC driver kits
before installing the new driver kit. Please refer to the "Driver
Uninstallation" section to uninstall previous versions of the
Emulex LPFC 7.x or older driver.

Log in as the user 'root' to a terminal, change to the directory in
which the Emulex LPFC 7.1 driver kit is installed, and execute the
'lpfc-install' script with no options to install the driver:

./lpfc-install

Once the 'lpfc-install' script has completed successfully, the
Emulex LPFC and LPFC DFC drivers will be loaded, and fibre channel
disks that are properly connected to the system should be
accessible. However, a reboot of the system is recommended to load
the 'lpfc' driver through the ramdisk.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

IOCTL Application helper module

Operating System

Linux 2.6 Kernel

Version

8.0.16.17

Size Driver

202KB

File Name

lpfc_2.6_ioctl_module_kit-2.0.9-2.tar.gz

Observations

RHEL4 Update 2 x86 (Intel), x86-64 (AMD and Intel), IA64
and SLES 9 SP3 x86 (Intel), X86-64 (AMD and Intel), IA64
Tar file containing install script and scripted source RPM to build and install the IOCTL application helper module. This is needed with the RHEL 4 Update 2 distribution (which contains the 8.0.16.17 driver). This driver allows applications to communicate with the 8.0.16.17 driver.

1. System Requirements
2. Description of Changes
3. Release Notes
3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
3.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC Application Helper Module:

Red Hat Enterprise Linux 4 Update 1
SuSE Linux Enterprise Server 9 SP2

2. Description of Changes

The ioctl-install script installs the LPFC Application Helper
Module RPM. This RPM installs the module sources to the
/usr/src/lpfcdfc directory, builds the module for the currently
running kernel, and then installs the module to the proper
directory for the currently running kernel.

Once the RPM is installed, the 'elxlpfc' init script is installed
and configured to start and stop the 'lpfcdfc' driver during system
startup and shutdown.

3. Release Notes

3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the kernel development
package with the same version as the currently running kernel must
be installed for the Application Helper Module build to succeed.
For example, a system with the 2.6.9-6.37.EL kernel would need the
kernel-devel-2.6.9-6.37.EL package, and a system with the
2.6.9-6.37.ELsmp kernel would need the
kernel-smp-devel-2.6.9-6.37.EL package.

3.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the Application Helper Module build to succeed.
For example, a system with the 2.6.5-7.166-bigsmp kernel would need
the kernel-source-2.6.5-7.166 package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.48.2p

Size Driver

208.6MB

File Name

elxlinuxapps-4.1a36-8.2.0.48.2p-1-1.tar

Observations

Red Hat Enterprise Linux 5.4 and SUSE SLES 10 SP3 (x86 Intel,x86-64 AMD & Intel architectures)
HBAnyware utility 4.1a36

HBAnyware 4.1a36 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.1a36
SSC version 4.1a36
DFC Library version 3.0.35-1-1
HBAAPI version 2.1.g
FCAUTHD version 1.20-1-1
Multipulse version 3.0.30-1
Dependencies:

lpfc driver version 8.2.0.48.2p or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.2.8.14

Size Driver

170.9MB

File Name

elxlinuxapps-4.1a36-8.2.8.14-1-1.tar

Observations

SLES 11 (x86 Intel,x86-64 AMD & Intel)
HBAnyware utility 4.1a26 (170 MB tar file)

HBAnyware 4.1a36 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.1a36
SSC version 4.1a36
DFC Library version 3.1.12-1-1
HBAAPI version 2.1.g
FCAUTHD version 2.5-1-1

Dependencies:

lpfc driver version 8.2.8.14 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DKMS Kit

Operating System

Linux 2.6 Kernel

Version

7.1.14

Size Driver

345KB

File Name

lpfc_2.4_dkms_kit-7.1.14-3.tar.gz

Observations

RHEL 3.0 Update 5 x86 (Intel), x86-64 (AMD and Intel) and x64 (Intel); Asianux 1.0 and SP1.
Tar file containing the DKMS package installation and DKMS RPMs for the 7.1.14 and IOCTL application helper module. This kit is supported on Red Hat 2.1 and 3.0 distributions only. It automatically installs the drivers; no lpfc.conf parameter customization is needed prior to 1st driver compilation. This is an alternative installation method to using driver kits above, or drivers on the Redhat distribution CDs. (345 KB).

The DKMS (Dynamic Kernel Module System) project
is maintained by Dell. The latest version can
be found at http://linux.dell.com/dkms/dkms.html

DKMS creates a framework where kernel dependent
module source is stored in the DKMS database.
DKMS manages the building and installation
of the lpfc and lpfcdfc modules. These RPMs
contain the same lpfc source code as the non-DKMS
RPMs but include DKMS in the RPM package name to
signify that the RPM includes our driver managed by DKMS.
The driver itself is the same, just the packaging
is different.
DKMS RPMs for Emulex 7.1.14 linux FC driver
-------------------------------------------

Installation:
------------
1. Ensure that DKMS is installed. DKMS version
2.0.4-1 or greater is required. You may install
the DKMS RPM that is included as part of this
package.

rpm -i dkms-2.0.4-1.noarch.rpm

2. Install the dkms specific lpfc driver rpm

rpm -i lpfcdkms-7.1.14-3.noarch.rpm

3. Install the dkms specific lpfcdfc driver rpm

rpm -i lpfcdfcdkms-1.0.13-2.noarch.rpm
Post-Install:
-----------
1. Use the DKMS status command to verify that DKMS has
built and installed the drivers.

e.g.
[root]# dkms status
lpfc, 7.1.14, 2.4.21-15.ELsmp, i686: installed (original_module exists)
lpfcdfc, 1.0.13, 2.4.21-15.ELsmp, i686: installed (original_module exists)

2. DKMS automatically builds the lpfc driver into the initial ram disk so that
lpfc is loaded on boot. To load the driver either reboot or issue comamnds;

modprobe lpfc
modprobe lpfcdfc

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DKMS RPM Driver Kit

Operating System

Linux 2.6 Kernel

Version

7.3.2

Size Driver

344KB

File Name

lpfc_2.4_dkms_kit-7.3.2-3.tar.gz

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
Tar file containing the DKMS package installation and DKMS RPMs for the 7.3.2 module. This kit is supported on Red Hat distributions only. It automatically installs the drivers; no lpfc.conf parameter customization is needed prior to 1st driver compilation. This is an alternative installation method to using driver kits above, or drivers on the Redhat distribution CDs. (344KB gz file)

Emulex 7.3.2 FC Driver and IOCTL Package

Introduction
------------

The DKMS (Dynamic Kernel Module System) project is maintained by Dell.
The latest version can be found at:

http://linux.dell.com/dkms/dkms.html

DKMS creates a framework where kernel dependent module source is
stored in the DKMS database. DKMS manages the building and
installation of the lpfc and lpfcdfc modules. These RPMs contain the
same lpfc source code as the non-DKMS RPMs but include DKMS in the RPM
package name to signify that the RPM includes our driver managed by
DKMS. The driver itself is the same, just the packaging is different.
DKMS RPMs for Emulex 7.3.2 linux FC driver
-------------------------------------------

Installation:
------------
1. Ensure that DKMS is installed. DKMS version 2.0.5-1 or greater is
required. You may install the DKMS RPM that is included as part of
this package.

rpm -i dkms-2.0.5-1.noarch.rpm

2. Install the dkms specific lpfc driver rpm

rpm -i lpfcdkms-7.3.2-1.noarch.rpm

3. Install the dkms specific lpfcdfc driver rpm

rpm -i lpfcdfcdkms-1.2.1-1.noarch.rpm

Post-Install:
-----------
1. Use the DKMS status command to verify that DKMS has built and
installed the drivers:

[root]# dkms status
lpfc, 7.3.2, 2.4.21-15.ELsmp, i686: installed (original_module exists)
lpfcdfc, 1.2.1, 2.4.21-15.ELsmp, i686: installed (original_module exists)

2. DKMS automatically builds the lpfc driver into the initial ram disk
so that lpfc is loaded on boot. To load the driver either reboot
or issue the following commands:

modprobe lpfc
modprobe lpfcdfc

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit 2.1.6

Operating System

Linux 2.6 Kernel

Version

8.1.6

Size Driver

159.3MB

File Name

elxlinuxapps-3.0a15-8.1.6-2-1.tar

Observations

8.1.6 SLES10 (Linux CD)
Emulex device driver v8.1.6 is included in the SUSE Linux Enterprise Server 10 distribution
HBAnyware utility 3.0a15, lputil 2.0a14, Application helper module 2.1.1 (163 MB tar file)

HBAnyware 3.0a15 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.0a15
SSC version 3.0a15
DFC Library version 80.162-1
Lputil version 2.0a14
HBAAPI version 2.1.c
DFC helper module

Dependencies:

lpfc driver version 8.1.6-2 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

HBAnyware requires the kernel development environment as described here:

This kit installs the Emulex Application Helper Module for the
currently running kernel. Since this installation procedure builds
the module for the currently running kernel, the kernel development
environment must be installed. For systems running Red Hat Enterprise
Linux (RHEL) 4, the appropriate kernel-devel package is required; for
example, a system with the 2.6.9-22.EL kernel would need the
kernel-devel-2.6.9-22.EL package, and a system with the 2.6.9-22.ELsmp
kernel would need the kernel-smp-devel-2.6.9-22.EL package. For
systems running SuSE Linux Enterprise Server (SLES) 9, the appropriate
kernel-source package is required; for example, a system with the
2.6.5-7.139-bigsmp kernel would need the kernel-source-2.6.5-7.139
package.
A log of each installation and uninstallation is recorded in the
following file:

/usr/src/lpfcdfc/utils-install.log
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

tar v2.02e 32-Bit RHEL 2.1

Operating System

Linux 2.6 Kernel

Version

2.02e

Size Driver

9.1MB

File Name

linux-2.02e-i386-rh2.1-tar-1a.tar

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
32-Bit RHEL 2.1 Intel (10 MB gz file)

This kit contains the following components:

lpfcdriver-2.02e.tgz - Emulex Fibre Channel Linux Driver
EmlxApps300a8-i386-RH2.1-TAR.tar - Emulex Applications kit
readme.first.txt - this file

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found on the
Emulex website - www.emulex.com, under /ts/docfc/linuxframe.htm.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications kit
can be found in the README.txt file contained in the EmlxApps300a8-i386-RH2.1-TAR.tar package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

tar v2.02e 32-Bit RHEL 3.0

Operating System

Linux 2.6 Kernel

Version

2.02e

Size Driver

8.8MB

File Name

linux-2.02e-i386-rh3.0-tar-1a.tar

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
32-Bit RHEL 3.0 Intel (9 MB gz file)

This kit contains the following components:

lpfcdriver-2.02e.tgz - Emulex Fibre Channel Linux Driver
EmlxApps300a8-i386-RH3.0-TAR.tar - Emulex Applications kit
readme.first.txt - this file

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found on the
Emulex website - www.emulex.com, under /ts/docfc/linuxframe.htm.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications kit
can be found in the README.txt file contained in the EmlxApps300a8-i386-RH3.0-TAR.tar package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

tar v2.02e 32-Bit SuSE SLES 8

Operating System

Linux 2.6 Kernel

Version

2.02e

Size Driver

9.6MB

File Name

linux-2.02e-i386-sl8-tar-1a.tar

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
32-Bit SuSE SLES 8 Intel (9.8 MB gz file)

This kit contains the following components:

lpfcdriver-2.02e.tgz - Emulex Fibre Channel Linux Driver
EmlxApps300a8-i386-SL8-TAR.tar - Emulex Applications kit
readme.first.txt - this file

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found on the
Emulex website - www.emulex.com, under /ts/docfc/linuxframe.htm.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications kit
can be found in the README.txt file contained in the EmlxApps300a8-i386-SL8-TAR.tar package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.22

Size Driver

198.5MB

File Name

elxlinuxapps-3.4a14-8.2.0.22-2-2.tar

Observations

Red Hat Enterprise Linux 5.2 and SUSE SLES 10 SP2 (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware utility 3.4a14 (198 MB tar file)

HBAnyware 3.4a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.4a14
SSC version 3.4a14
DFC Library version 3.0.13-1
Lputil version
HBAAPI version 2.1.g

Dependencies:

lpfc driver version 8.2.0.22 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.29

Size Driver

179.1MB

File Name

elxlinuxapps-4.0a31-8.2.0.29-1-1.tar

Observations

Red Hat Enterprise Linux 5.0 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) SUSE Linux Enterprise Server 10 SP1 or later (x86 and x64, Intel Itanium2 and PowerPC 64-bit architectures) Oracle Enterprise Linux 5 or later (x86 and x64 architectures)
HBAnyware utility 4.0a31 (179 MB tar file)

HBAnyware 4.0a31 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.0a31
SSC version 4.0a31
DFC Library version 3.0.25-1-1
HBAAPI version 2.1.g
Multipulse version 3.0.30-1
FCAUTHD version 1.17-1-1
Dependencies:

lpfc driver version 8.2.0.29 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.33.3p

Size Driver

208.6MB

File Name

elxlinuxapps-4.1a36-8.2.0.33.3p-1-1.tar

Observations

Red Hat Enterprise Linux 5.3, SUSE SLES 11 (x86 Intel,x86-64 AMD & Intel architectures)
HBAnyware utility 4.1a36

HBAnyware 4.1a36 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.1a36
SSC version 4.1a36
DFC Library version 3.0.35-1-1
HBAAPI version 2.1.g
FCAUTHD version 1.19-1-1
Multipulse version 3.0.30-1
Dependencies:

lpfc driver version 8.2.0.33.3p or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.6_p3

Size Driver

155.1MB

File Name

elxlinuxapps-2.1a14-8.0.16.7-1.tar

Observations

SUSE SLES9 SP2 x86 (Intel), x64 (Intel), x86-64 (AMD and Intel), IA64
Applications kit includes HBAnyware v2.1a14 and LPUTIL v2.0a4. (158 MB tar file)

HBAnyware 2.1a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a14
SSC version 2.1a14
DFC Library version 8.0.16.7
Lputil version 2.0a4
HBAAPI version 2.1.a

Dependencies:

lpfc 8.0.16.7
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the ElxLinuxApps-2.1a14-8.0.16.7-1.tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf ElxLinuxApps-2.1a14-8.0.16.7-1.tar
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.1.10.3

Size Driver

165.1MB

File Name

elxlinuxapps-3.2a5-8.1.10.3-1-2.tar

Observations

RHEL5 x86 (Intel), x86-64 (AMD and Intel), IA64
and SLES 9 SP1 x86 (Intel) x86-64 (AMD and Intel), IA64
HBAnyware utility 3.2a5, lputil 2.0a14 (169 MB tar file)

HBAnyware 3.2a5 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.2a5
SSC version 3.2a5
DFC Library version 2.15.1000
Lputil version 2.0a14
HBAAPI version 2.1.e

Dependencies:

lpfc driver version 8.1.10.3 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI
or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.1.10.9

Size Driver

207.1MB

File Name

elxlinuxapps-3.2a14-8.1.10.9-1-6.tar

Observations

RHEL5.1 x86 (Intel), x86-64 (AMD and Intel), IA64
SLES 10 SP1 (x86 Intel, x86-64 AMD and Intel), IA64
HBAnyware utility 3.2a5, lputil 2.0a14 (169 MB tar file)

HBAnyware 3.2a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.2a14
SSC version 3.2a14
DFC Library version 2-15-1005
Lputil version 2.0a14
HBAAPI version 2.1.e

Dependencies:

HBAnyware requires that the lpfc driver module be installed.
The lpfc driver version 8.1.10.9 and all 8.1.10.x based driver releases are
supported with this version of HBAnyware.
This support includes the RHEL5 and SLES10-SP1 in-distro 8.1.10.3 lpfc driver.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.46

Size Driver

176.6MB

File Name

elxlinuxapps-4.0a38-8.0.16.46-1-1.tar

Observations

RHEL 4.8 (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and 64-bit architectures)
HBAnyware utility 4.0a38, Application helper module 2.0.38-1

HBAnyware 4.0a38 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.0a38
SSC version 4.0a38
DFC Library version 80.206-1
HBAAPI version 2.1.g
Multipulse version 3.0.30-1
IOCTL Module version 2.0.36-1
Dependencies:

lpfc driver version 8.0.16.46 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.47

Size Driver

176.6MB

File Name

elxlinuxapps-4.0a38-8.0.16.47-1-1.tar

Observations

Asianux 2.0 SP2 and later (x86, x64, Intel Itanium2 and PowerPC 64-bit architectures)
HBAnyware utility 4.0a38, Application helper module 2.0.39-1 (176 MB tar file)
Note: This kit does not support Intel Itanium2 architecture. For Intel Itanium2 architecture support, download the corresponding core (CLI) applications kit.

HBAnyware 4.0a38 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 4.0a38
SSC version 4.0a38
DFC Library version 80.206-1
HBAAPI version 2.1.g
Multipulse version 3.0.30-1
IOCTL Module version 2.0.39-1
Dependencies:

lpfc driver version 8.0.16.47 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.34

Size Driver

187.9MB

File Name

elxlinuxapps-3.3a20-8.0.16.34-1-1.tar

Observations

RHEL 4.6 and SLES 9 SP4 (x86 Intel,x86-64 AMD & Intel, IA64)
HBAnyware 3.03a20 lputil 2.0a14

HBAnyware 3.3a20 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.3a20
SSC version 3.3a20
DFC Library version 80.164-2
Lputil version 2.0a14
HBAAPI version 2.1.d_1

Dependencies:

lpfc driver version 8.0.16.34 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.40

Size Driver

196.4MB

File Name

elxlinuxapps-3.4a14-8.0.16.40-2-1.tar

Observations

RHEL 4.7 and SLES 9 SP4 (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware utility 3.4a14, Application helper module 2.0.30

HBAnyware 3.4a14 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 3.4a14
SSC version 3.4a14
DFC Library version 80.164-8
Lputil version
HBAAPI version 2.1.g

Dependencies:

lpfc driver version 8.0.16.40 or later

HBAnyware requires that the lpfc driver module be installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.
Installing HBAnyware:

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. cd (change directory) to the "ElxLinuxApps.." directory created by step 3
5. su to root
6. If earlier HBAnyware version currently installed, type : ./uninstall
7. Run the install script: ./install
8. When prompted, answer the following question:

Select desired mode of operation for HBAnyware

1 Local Mode : HBA's on this Platform can be managed by HBAnyware
clients on this platform only.
2 Managed Mode : HBA's on this Platform can be managed by local or
remote HBAnyware clients
3 Remote Mode : Same as '2' plus HBAnyware clients on this Platform
can manage local and remote clients.

Enter the number '1' or '2' or '3'
9. When prompted, answer the following question:

Do you want to allow user to make subsequent management mode changes
using 'set_operating_mode' script
Enter the letter 'Y' for yes or 'N' for no

10. Installation Complete: type /usr/sbin/hbanyware/hbanyware
to start GUI or type /usr/sbin/hbanyware/hbacmd list
to run script utility

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.17

Size Driver

165.4MB

File Name

elxlinuxapps-2.1a25-8.0.16.17-1-1.tar

Observations

RHEL4 Update 2 x86 (Intel), x86-64 (AMD and Intel), IA64
and SLES 9 SP3 x86 (Intel), X86-64 (AMD and Intel), IA64
HBAnyware utility 2.1a25, lputil 2.0a9 (169 MB tar file)

HBAnyware 2.1a25 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a25
SSC version 2.1a25
DFC Library version 80.161-5
Lputil version 2.0a9
HBAAPI version 2.1.a

Dependencies:

lpfc driver version 8.0.16.17 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.18

Size Driver

165.6MB

File Name

elxlinuxapps-2.1a29-8.0.16.18-1-1.tar

Observations

RHEL4 Update 3 x86 (Intel), x86-64 (AMD and Intel) and IA64
HBAnyware utility 2.1a29, lputil 2.0a12

HBAnyware 2.1a29 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a29
SSC version 2.1a29
DFC Library version 80.161-5
Lputil version 2.0a12
HBAAPI version 2.1.a

Dependencies:

lpfc driver version 8.0.16.18 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

7.3.2

Size Driver

175.3MB

File Name

elxlinuxapps-2.1a24-7.3.2-1-2.tar

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
HBAnyware utility 2.1a24, lputil 2.0a9 (180 MB tar file)

HBAnyware 2.1a24 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a24
SSC version 2.1a24
DFC Library version 1.2.1-1
Lputil version 2.0a9
HBAAPI version 2.0.f

Dependencies:

lpfc driver version 7.3.2-1 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

7.3.3

Size Driver

175.7MB

File Name

elxlinuxapps-2.1a29-7.3.3-1-2.tar

Observations

RHEL 3.0 Update 7 x86 (Intel), x86-64 (AMD and Intel) and IA64
Applications kit includes HBAnyware v2.1a29 and LPUTIL v2.0a12. (180 MB tar file)

HBAnyware 2.1a29 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a29
SSC version 2.1a29
DFC Library version 1.2.1-1
Lputil version 2.0a12
HBAAPI version 2.0.f

Dependencies:

lpfc driver version 7.3.3 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

7.3.6

Size Driver

175.7MB

File Name

elxlinuxapps-2.1a29-7.3.6-1-3.tar

Observations

RHEL 3.0 Update 8 x86 (Intel), x86-64 (AMD and Intel), IA64
Includes HBAnyware v2.1a29 and LPUTIL v2.0a12. (180 MB tar file)

HBAnyware 2.1a29 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.1a29
SSC version 2.1a29
DFC Library version 1.2.1-1
Lputil version 2.0a12
HBAAPI version 2.0.f

Dependencies:

lpfc driver version 7.3.6 or later
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

HBAnyware requires a minimum screen resolution of 1024 x 768.

Installing HBAnyware

1. Copy the applications kit tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf tarfilename
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

EMC RPM v2.02e

Operating System

Linux 2.6 Kernel

Version

2.02e

Size Driver

330KB

File Name

emulex-2.02e-1dkms.tgz

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
EMC-approved RPM for Red Hat distributions only which automatically installs driver and application software; no parameter customization prior to 1st driver compilation. 32-Bit RHEL 2.1/3.0 Intel(330 KB gz file)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.33.3p

Size Driver

289KB

File Name

lpfc_2.6_driver_kit-8.2.0.33.3p-1.tar.gz

Observations

Red Hat Enterprise Linux 5.3, SUSE SLES 11 (x86 Intel,x86-64 AMD & Intel architectures)
Base driver and install script

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround
3.2 Deletion of Vports/PCI Hot Unplug
3.2.1 Observed Problem
3.2.2 Background
3.3 lspci utility displays "Unknown Device" for LPe12000 HBAs
3.3.1 Observed Problem
3.3.2 Background
3.4 Speed of LPe12000 HBA (8Gb) is incorrectly displayed by HBAnyware
3.4.1 Observed Problem
3.4.2 Background
3.5 Port disabled on system boot or HBA reset with authentication enabled
3.5.1 Observed Problem
3.5.2 Workaround
3.6 LILO Boot Loader is not supported - i386 and x86_64 architectures
3.6.1 Observed Problem
3.6.2 Background
3.7 Order of lpfc module in initrd module list
3.7.1 Observed Problem
3.7.2 Workaround
3.8 Devloss timeout after swapping ports
3.8.1 Observed Problem
3.8.2 Workaround
3.9 Suspend to disk and Resume support
3.9.1 Observed Problem
3.9.2 Background
3.10 Deleting vports while devices are in use
3.10.1 Observed Problem
3.10.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 5
SuSE Linux Enterprise Server 10 (SP1 or higher)

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the -devel package
which matches the kernel package with the same version as the
currently running kernel must be installed for the LPFC driver
build to succeed. For example, a system with the 2.6.18-7 kernel
would need the kernel-devel-2.6.18-7 package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.48.2p

Size Driver

452KB

File Name

lpfc_2.6_driver_kit-8.2.0.48.2p-1.tar.gz

Observations

Red Hat Enterprise Linux 5.4 and SUSE SLES 10 SP3 (x86 Intel,x86-64 AMD & Intel architectures)
Base driver and install script

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround
3.2 Deletion of Vports/PCI Hot Unplug
3.2.1 Observed Problem
3.2.2 Background
3.3 lspci utility displays "Unknown Device" for LPe12000 HBAs
3.3.1 Observed Problem
3.3.2 Background
3.4 Speed of LPe12000 HBA (8Gb) is incorrectly displayed by HBAnyware
3.4.1 Observed Problem
3.4.2 Background
3.5 Port disabled on system boot or HBA reset with authentication enabled
3.5.1 Observed Problem
3.5.2 Workaround
3.6 LILO Boot Loader is not supported - i386 and x86_64 architectures
3.6.1 Observed Problem
3.6.2 Background
3.7 Order of lpfc module in initrd module list
3.7.1 Observed Problem
3.7.2 Workaround
3.8 Devloss timeout after swapping ports
3.8.1 Observed Problem
3.8.2 Workaround
3.9 Suspend to disk and Resume support
3.9.1 Observed Problem
3.9.2 Background
3.10 Deleting vports while devices are in use
3.10.1 Observed Problem
3.10.2 Workaround
3.11 Support of 4Gb/s HBAs in Direct I/O virtualized environments
3.11.1 Observed Problem
3.11.2 Workaround
3.12 Potential error messages during driver kit removal process
3.12.1 Observer Problem
3.12.2 Resolution

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 5
SuSE Linux Enterprise Server 10 (SP1 or higher)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.2.8.14

Size Driver

333KB

File Name

lpfc_2.6_driver_kit-8.2.8.14-1.tar.gz

Observations

SLES 11 (x86 Intel,x86-64 AMD & Intel)
Base driver and install script (333 KB gz file)

1. System Requirements
1.1 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround
3.2 Deletion of Vports/PCI Hot Unplug
3.2.1 Observed Problem
3.2.2 Background
3.3 Port disabled on system boot or HBA reset with authentication enabled
3.3.1 Observed Problem
3.3.2 Workaround
3.4 LILO Boot Loader is not supported - i386 and x86_64 architectures
3.4.1 Observed Problem
3.4.2 Background
3.5 Order of lpfc module in initrd module list
3.5.1 Observed Problem
3.5.2 Workaround
3.6 Devloss timeout after swapping ports
3.6.1 Observed Problem
3.6.2 Workaround
3.7 Deleting vports while devices are in use
3.7.1 Observed Problem
3.7.2 Workaround
3.8 Support of 4Gb/s HBAs in Direct I/O virtualized environments
3.8.1 Observed Problem
3.8.2 Workaround
----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

SuSE Linux Enterprise Server 11

1.1 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the LPFC driver build to succeed. For example, a
system with the 2.6.27-rc7-12-default kernel would need the
kernel-source-2.6.27-12.1 package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.2.0.29

Size Driver

285KB

File Name

lpfc_2.6_driver_kit-8.2.0.29-1.tar.gz

Observations

Red Hat Enterprise Linux 5.2 and Novell SUSE SLES 10 SP2 (x86 Intel,x86-64 AMD & Intel architectures)
Base driver and install script for RHEL 5.2 (288 KB gz file)

1. System Requirements
1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
1.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement
2. Description of Install Procedure
3. Known Issues
3.1 PCI Hot Plug Support for applications
3.1.1 Observed problem
3.1.2 Workaround
3.2 Deletion of Vports/PCI Hot Unplug
3.2.1 Observed Problem
3.2.2 Background
3.3 lspci utility displays "Unknown Device" for LPe12000 HBAs
3.3.1 Observed Problem
3.3.2 Background
3.4 Speed of LPe12000 HBA (8Gb) is incorrectly displayed by HBAnyware
3.4.1 Observed Problem
3.4.2 Background
3.5 Port disabled on system boot or HBA reset with authentication enabled
3.5.1 Observed Problem
3.5.2 Workaround
3.6 LILO Boot Loader is not supported - i386 and x86_64 architectures
3.6.1 Observed Problem
3.6.2 Background
3.7 Order of lpfc module in initrd module list
3.7.1 Observed Problem
3.7.2 Workaround
3.8 Devloss timeout after swapping ports
3.8.1 Observed Problem
3.8.2 Workaround
3.9 Suspend to disk and Resume support
3.9.1 Observed Problem
3.9.2 Background
3.10 Deleting vports while devices are in use
3.10.1 Observed Problem
3.10.2 Workaround

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC driver:

Red Hat Enterprise Linux 5
SuSE Linux Enterprise Server 10 (SP1 or higher)

1.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the -devel package
which matches the kernel package with the same version as the
currently running kernel must be installed for the LPFC driver
build to succeed. For example, a system with the 2.6.18-7 kernel
would need the kernel-devel-2.6.18-7 package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DKMS RPM Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.18

Size Driver

289KB

File Name

lpfc_2.6_dkms_kit-8.0.16.18-1.tar.gz

Observations

RHEL4 Update 3 x86 (Intel), x86-64 (AMD and Intel) and IA64
Tar file containing the DKMS package installation and DKMS RPMs for the 8.0.16.18 and application helper module. This kit is supported on RHEL 4 distribution only. It automatically installs the drivers; no lpfc.conf parameter customization is needed prior to 1st driver compilation. This is an alternative installation method to using driver kits above, or drivers on the Redhat distribution CDs

1. Introduction
2. Installation
3. Post-Installation
4. Uninstallation
5. Distribution/Platform Support
6. Notes

----------------------------------------------------------------------

1. Introduction

The DKMS (Dynamic Kernel Module System) project is maintained by
Dell. The latest version can be found at:

http://linux.dell.com/dkms/dkms.html

DKMS creates a framework where kernel dependent module source is
stored in the DKMS database. DKMS manages the building and
installation of the lpfc and lpfcdfc modules. These RPMs contain
the same lpfc source code as the non-DKMS RPMs but include DKMS in
the RPM package name to signify that the RPM includes our driver
managed by DKMS. The driver itself is the same, just the packaging
is different.
2. Installation

1. Ensure that DKMS is installed. DKMS version 2.0.5-1 or greater
is required. You may install the DKMS RPM that is included as
part of this package.

rpm -i dkms-2.0.5-1.noarch.rpm

2. Install the dkms specific lpfc driver rpm

rpm -i lpfcdriver_2.6_dkms-8.0.16.18-1.noarch.rpm

3. Install the dkms specific lpfcdfc driver rpm

rpm -i lpfc_2.6_ioctl_module_dkms-2.0.9-2.noarch.rpm
3. Post-Installation

1. Use the DKMS status command to verify that DKMS has built and
installed the drivers.

e.g.
[root]# dkms status
lpfc, 8.0.16.18, 2.6.9-22.ELsmp, i686: installed (original_module exists)
lpfcdfc, 2.0.9, 2.6.9-22.ELsmp, i686: installed

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DKMS RPM Driver Kit

Operating System

Linux 2.6 Kernel

Version

7.3.3

Size Driver

344KB

File Name

lpfc_2.4_dkms_kit-7.3.3-1.tar.gz

Observations

RHEL 3.0 Update 7 x86 (Intel), x86-64 (AMD and Intel) and IA64
Tar file containing the DKMS package installation and DKMS RPMs for the 7.3.3 module. This kit is supported on Red Hat distributions only. It automatically installs the drivers; no lpfc.conf parameter customization is needed prior to 1st driver compilation. This is an alternative installation method to using driver kits, or drivers on the Redhat distribution CDs. (344 KB gz file)

The DKMS (Dynamic Kernel Module System) project is maintained by Dell.
The latest version can be found at:

http://linux.dell.com/dkms/dkms.html

DKMS creates a framework where kernel dependent module source is
stored in the DKMS database. DKMS manages the building and
installation of the lpfc and lpfcdfc modules. These RPMs contain the
same lpfc source code as the non-DKMS RPMs but include DKMS in the RPM
package name to signify that the RPM includes our driver managed by
DKMS. The driver itself is the same, just the packaging is different.
DKMS RPMs for Emulex 7.3.3 linux FC driver
-------------------------------------------

Installation:
------------
1. Ensure that DKMS is installed. DKMS version 2.0.5-1 or greater is
required. You may install the DKMS RPM that is included as part of
this package.

rpm -i dkms-2.0.5-1.noarch.rpm

2. Install the dkms specific lpfc driver rpm

rpm -i lpfcdkms-7.3.3-1.noarch.rpm

3. Install the dkms specific lpfcdfc driver rpm

rpm -i lpfcdfcdkms-1.2.1-1.noarch.rpm

Post-Install:
-----------
1. Use the DKMS status command to verify that DKMS has built and
installed the drivers:

[root]# dkms status
lpfc, 7.3.3, 2.4.21-15.ELsmp, i686: installed (original_module exists)
lpfcdfc, 1.2.1, 2.4.21-15.ELsmp, i686: installed (original_module exists)

2. DKMS automatically builds the lpfc driver into the initial ram disk
so that lpfc is loaded on boot. To load the driver either reboot
or issue the following commands:

modprobe lpfc

3. The lpfcdfc module will not be automatically loaded at boot time.
This module is required for the HBAnyware and lputil applications
to execute properly. To load this module, issue the following
command:

modprobe lpfcdfc

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DKMS RPM Driver Kit

Operating System

Linux 2.6 Kernel

Version

8.0.16.17

Size Driver

203KB

File Name

lpfc_2.6_ioctl_module_kit-2.0.9-1.tar.gz

Observations

RHEL4 Update 2 x86 (Intel), x86-64 (AMD and Intel), IA64
and SLES 9 SP3 x86 (Intel), X86-64 (AMD and Intel), IA64
Tar file containing the DKMS package installation and DKMS RPMs for the 8.0.16.17 and application helper module. This kit is supported on RHEL 4 distribution only. It automatically installs the drivers; no lpfc.conf parameter customization is needed prior to 1st driver compilation. This is an alternative installation method to using driver kits above, or drivers on the Redhat distribution CDs.

1. System Requirements
2. Installation Process
3. Release Notes
3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
3.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

----------------------------------------------------------------------

1. System Requirements

The following distribution of Linux is supported by the Emulex
LPFC Application Helper Module:

Red Hat Enterprise Linux 4 Update 2

This Emulex LPFC Application Helper Module will function with the
Emulex LPFC driver that ships with this distribution of Linux.
Other versions of the LPFC driver will not function properly with
this version of the Application Helper Module.

2. Installation Process

The ioctl-install script can be used to install and uninstall the
LPFC Application Helper Module RPM. This RPM installs the module
sources to the /usr/src/lpfcdfc directory, builds the module for
the currently running kernel, and then installs the module to the
proper directory for the currently running kernel.

Once the RPM is installed, the 'elxlpfc' init script is installed
and configured to start and stop the 'lpfcdfc' driver during system
startup and shutdown.

For usage information, please execute the command:

./ioctl-install --help

3. Release Notes

3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the "Development Tools"
package in the software development environment and the kernel
development package with the same version as the currently running
kernel must be installed for the Application Helper Module build to
succeed.

The name of the kernel development package depends upon the name of
the kernel for which the Application Helper Module will be
installed. For example, a system with the 2.6.9-11.EL kernel
would need the kernel-devel-2.6.9-11.EL package, and a system
with the 2.6.9-11.ELsmp kernel would need the
kernel-smp-devel-2.6.9-11.EL package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Application helper module

Operating System

Linux 2.6 Kernel

Version

8.0.16.6_p3

Size Driver

201KB

File Name

lpfc_2.6_ioctl_module_kit-2.0.2-2.tar.gz

Observations

SUSE SLES9 SP2 x86 (Intel), x64 (Intel), x86-64 (AMD and Intel), IA64
Use this file only with the SUSE SLES9 SP2 distribution, which contains the 8.0.16.6_p3 driver. Note: The same Application Helper Module is applicable to both RHEL4 and SLES9. (201 KB gz file)

1. System Requirements
2. Description of Changes
3. Release Notes
3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement
3.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

----------------------------------------------------------------------

1. System Requirements

The following distributions of Linux are supported by the Emulex
LPFC Application Helper Module:

Red Hat Enterprise Linux 4 Update 1
SuSE Linux Enterprise Server 9 SP2

2. Description of Changes

The ioctl-install script installs the LPFC Application Helper
Module RPM. This RPM installs the module sources to the
/usr/src/lpfcdfc directory, builds the module for the currently
running kernel, and then installs the module to the proper
directory for the currently running kernel.

Once the RPM is installed, the 'elxlpfc' init script is installed
and configured to start and stop the 'lpfcdfc' driver during system
startup and shutdown.

3. Release Notes

3.1 Red Hat Enterprise Linux 'kernel-devel' Package Requirement

For Red Hat Enterprise Linux installations, the kernel development
package with the same version as the currently running kernel must
be installed for the Application Helper Module build to succeed.
For example, a system with the 2.6.9-6.37.EL kernel would need the
kernel-devel-2.6.9-6.37.EL package, and a system with the
2.6.9-6.37.ELsmp kernel would need the
kernel-smp-devel-2.6.9-6.37.EL package.

3.2 SuSE Linux Enterprise Server 'kernel-source' Package Requirement

For SuSE Linux Enterprise Server installations, the kernel-source
package with the same version as the currently running kernel must
be installed for the Application Helper Module build to succeed.
For example, a system with the 2.6.5-7.166-bigsmp kernel would need
the kernel-source-2.6.5-7.166 package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

Linux 2.6 Kernel

Version

7.1.14

Size Driver

139.7MB

File Name

elxlinuxapps-2.0a20-7.1.14-1.tar

Observations

RHEL 3.0 Update 5 x86 (Intel), x86-64 (AMD and Intel) and x64 (Intel); Asianux 1.0 and SP1.
This kit includes the Tar file containing the management utilites: HBAnyware v2.0a20 and LPUTIL v1.6a10. (143 MB).

HBAnyware 2.0a20 Linux Installation Instructions

This installation kit contains the following components:

HBAnyware version 2.0a20
SSC version 2.0a15
DFC Library version 7.1.14
Lputil version 1.6a10
HBAAPI version 2.0.f

Dependencies:

lpfc 7.1.14
HBAnyware is dependant on lpfc being installed, so install lpfc first if it is not already installed.

Installing HBAnyware

1. Copy the ElxLinuxApps-2.0a20-7.1.14-1.tar file to a directory on the install machine
2. cd to the directory which you copied the tar file
3. Untar the file: tar -xvf ElxLinuxApps-2.0a20-7.1.14-1.tar
4. su to root
5. Run the install script: ./install
Uninstalling HBAnyware

1. Complete steps 1 through 4 from "Installing HBAnyware" above.
2. Run the uninstall script: ./uninstall
Running the HBAnyware GUI

1. su to root
2. Run the script /usr/sbin/hbanyware/hbanyware
ppc64/sles8 NOTE:
If you want to use the 64bit HBAAPI libraries you must replace the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib/libemulexhbaapi.so
with this line
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

ppc64/(non-sles8) and amd64 NOTE:
If you want to use the 64bit HBAAPI libraries you must add the following line in /etc/hba.conf:
com.emulex.emulexapilibrary /usr/lib64/libemulexhbaapi.so

HBAnyware Help:
To view the HBAnyware help pages or to access the Emulex Technical support pages you must have one of the
following web browsers installed:
mozilla, konqueror
Helpful scripts

/usr/sbin/hbanyware/stop_hbanyware - This script will stop all HBAnyware daemons and GUIs.
Run this if you need to unload the driver.

/usr/sbin/hbanyware/start_rmserver - This script will re-start the rmserver daemon.
Run this if you manually load the lpfc driver.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

IOCTL Application Helper Module

Operating System

Linux 2.6 Kernel

Version

7.1.14

Size Driver

68KB

File Name

lpfc_2.4_ioctl_module_kit-1.0.13-1.tar.gz

Observations

RHEL 3.0 Update 5 x86 (Intel), x86-64 (AMD and Intel) and x64 (Intel); Asianux 1.0 and SP1.
Tar file containing install script and scripted source RPM to build and install the IOCTL application helper module. This is needed with the RHEL 3 Update 1 distribution (which contains the 7.1.14 driver). This driver allows applications to communicate with the 7.1.14 driver.

1. System Requirements
2. Description of Changes
3. Errata

----------------------------------------------------------------------

1. System Requirements

The Emulex LPFC DFC driver RPM requires that the kernel sources be
installed on the system in order for the RPM installation to
succeed. The following distributions of Linux are supported by the
Emulex drivers:

Red Hat Enterprise Linux 3 Update 3

2. Description of Changes

The ioctl-install script installs the LPFC DFC driver RPM. This
RPM installs the driver sources to the /usr/src/lpfcdfc directory,
builds the driver for the currently running kernel, and then
installs the drivers to the proper directory for the currently
running kernel.

Once the RPM is installed, the 'elxlpfc' init script is installed
and configured to start and stop the 'lpfcdfc' driver during system
startup and shutdown.

3. Errata

- The Emulex HBAnyware configuration utility is not supported in
this release.

- On some large configurations, with many targets and other
initiators, FC discovery may not complete before the SCSI
subsystem probes for devices. If this occurs, some SCSI devices
may not be detected at boot. The missing devices can be detected
by requesting the SCSI subsystem to rescan via /proc/scsi/scsi
and the "scsi add-single-device "
mechanism. Emulex provides a script, called lun_scan, which
automates the scan requests for Emulex adapters. This script is
contained the driver applications kit. This script can be
integrated into the system run-level transitions to ensure that
all devices are fully detected.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

Windows 2003-2008

Operating System

Manual

Version

2.10a7

Size Driver

5.3MB

File Name

hbanyware.pdf

Observations

Qualification: Microsoft currently does not offer an FCoE WHQL "Certified for Windows" logo program. When the Storport Miniport driver is used with a standard Fibre Channel HBA, the driver is qualified for the "Certified for Windows" logo program. When the Storport MiniPort driver is used with an FCoE CNA, the driver is considered "unclassified" by Microsoft. In both cases, the Storport Miniport drivers are digitally signed by Microsoft and will be recognized by both Windows Sever 2003 and Windows Server 2008.
Note Windows Server 2003 SP2 and the KB943545 update to the Microsoft Storport driver are required. The KB943545 update must be applied before the Emulex Storport Miniport driver can be installed.
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

VMware ESX

Operating System

Manual

Version

8.2.030.52

Size Driver

3.9MB

File Name

hbanyware34_preliminary.pdf

Observations

ESX 4.0/4.0 U1 lpfc Driver 8.2.030.52 is embedded in the VMware release.
HBAnyware Utility User Manual

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 2
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 9
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................. 10
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Changing HBA Names .................................................................................... 15
Discovering HBAs ........................................................................................... 16
Automatic Fibre Channel Discovery .......................................................... 16
Remote SAN Management Using TCP/IP Access Protocol....................... 16
Adding a Single Host .......................................................................... 17
Adding a Range of Hosts .................................................................... 18
Removing Hosts.................................................................................. 19
Configuring Discovery Settings ................................................................. 19
Sorting HBA Information.................................................................................. 20
Viewing Remote and Local HBAs.............................................................. 20
Viewing HBA Information................................................................................. 21
Viewing Discovery Information .................................................................. 21
Viewing Host Information .......................................................................... 22
The Host Information Tab.................................................................... 22
The Driver Parameters Tab................................................................. 23
Viewing General HBA Attributes ............................................................... 24
Viewing Detailed HBA Information ............................................................ 26
Viewing Fabric Information........................................................................ 28
Viewing Target Information........................................................................ 29
Viewing LUN Information........................................................................... 30
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 31
Viewing Port Statistics............................................................................... 33
Viewing Firmware Information ................................................................... 35
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 36
Viewing Target Mapping (Linux) ................................................................ 37

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

VMware ESX

Operating System

Manual

Version

7.4.0.41

Size Driver

5.3MB

File Name

hbanyware.pdf

Observations

Virtual Infrastructure 3 v3.5 (ESX 3.5 U4, Virtual Center 2.5) - 10 Gb/s CNAs
The ESX 3.5 U2 lpdf Driver Version 7.4.0.41 is embedded in the VMware release.
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.2.0.33.3p

Size Driver

4.6MB

File Name

hbanyware.pdf

Observations

Red Hat Enterprise Linux 5.3, SUSE SLES 11 (x86 Intel,x86-64 AMD & Intel architectures)
HBAnyware Utility Version 4.1 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.2.0.22

Size Driver

3.5MB

File Name

hbanyware.pdf

Observations

Red Hat Enterprise Linux 5.2 and SUSE SLES 10 SP2 (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware Utility Version 3.4

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware User Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.0.16.40

Size Driver

5.3MB

File Name

hbanyware.pdf

Observations

RHEL 4.7 and SLES 9 SP4 (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures)
HBAnyware Utility Version 4.0 Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 1
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 8
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................... 9
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Discovering HBAs ........................................................................................... 14
Automatic Fibre Channel Discovery .......................................................... 14
Remote SAN Management Using TCP/IP Access Protocol....................... 15
Adding a Single Host .......................................................................... 15
Adding a Range of Hosts .................................................................... 16
Removing Hosts.................................................................................. 17
Configuring Discovery Settings ................................................................. 18
Sorting HBA Information.................................................................................. 19
Viewing Remote and Local HBAs.............................................................. 19
Viewing HBA Information................................................................................. 20
Viewing Discovery Information .................................................................. 20
Viewing Host Information .......................................................................... 21
The Host Information Tab.................................................................... 21
The Driver Parameters Tab................................................................. 22
Viewing General HBA Attributes ............................................................... 23
Viewing Detailed HBA Information ............................................................ 24
Viewing Fabric Information........................................................................ 26
Viewing Target Information........................................................................ 27
Viewing LUN Information........................................................................... 28
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 29
Viewing Port Statistics............................................................................... 31
Viewing Firmware Information ................................................................... 33
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 34
Viewing Target Mapping (Linux) ................................................................ 35

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware Release Notes

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.2.8.14

Size Driver

34KB

File Name

linux_release_notes.pdf

Observations

SLES 11 (x86 Intel,x86-64 AMD & Intel)
New features, fixed issues and known issues in the HBAnyware utility

Release Notes
Date: January 2010
Product: Driver for Linux
Version: FC and FCoE version 8.2.0.63
NIC version 2.101.374.0
iSCSI version 2.101.374.0

New Features in the Driver for Linux
1. Supports the OCe1010x OneConnect Universal Converged Network Adapters (CNAs).
2. Supports the OneCommand Manager application version 5.0. Refer to the OneCommand Manager
application User Manual for more information.
3. Adds PCI ID support for the LPSe12002-ML1-E EmulexSecure Fibre Channel Adapter.
4. Adds support for Advanced Error Reporting (AER) for PCIe HBAs.
Resolved Issues in the Driver for Linux
1. Multipath Package Issues Fixed
Corrected issues with the multipath package functions with the OneConnect UCNA.
2. FCF Failures Addressed
Resolved various FCF failures.
3. Corrected Adapter Reset
Corrected adapter reset and offline/online stress test failing with I/O errors.
4. Multiple Spurious Interrupts Corrected
Required OneConnect UCNA to set up and use single FCP EQ only under INTx interrupt mode. Changed
lpfc_use_msi module parameter to use INTx mode (not MSI) by default. This prevents multiple spurious
interrupts from the firmware.
5. Extended Error Handling Issue Resolved
Blocked all SCSI I/O requests from the midlayer until target rediscovery during Extended Error Handling
EEH.
6. VPort Log Out Issue Corrected
Corrected an issue that prevented a VPort to log out if deleted.
7. mbox sysfs Attribute Corrected
Corrected an issue that resulted in the mbox sysfs attribute smaller than the mailbox extension size.
8. LUN Panic Fixed
Fixed a potential panic if LUNs were unmapped.
9. CPU Lockup Fixed
Resolved an issue that caused the CPU to lock up or hang during boot when authentication is
enabled (fcauthd process is started).
10. Hot Plug Issue Resolved
Fixed a potential system panic issue during PCI Hot Plug.
11. List Corruption Fixed
Corrected an issue that caused a list corruption while unloading the driver.
12. Fabric Login Issue Fixed
Resolved an issue that caused the frame to be zeroed on the wire after a fabric login FLOGI .
13. Advanced Error Reporting Issue Resolved
Added logic to stop and abort all I/Os on an HBA for an advanced error reporting (AER) uncorrectable
non-fatal error handling.
14. AER sysfs entry Point Changed
Made the AER sysfs entry point return "Operation not permitted" for OneConnect UCNAs.
15. Unsolicited CT Exchange Sequences Fixed
Fixed handling of unsolicited CT exchange sequences.
16. Clear Virtual Link Support Added
Added support for Clear Virtual Link command.
17. devloss Timeout Issue Fixed
Corrected a devloss timeout issue when multiple initiators were in the same zone.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Release Notes

Information

Windows 2003-2008

Operating System

Manual

Version

2.20.006

Size Driver

26KB

File Name

driver_release_notes_b.pdf

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Release Notes

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.2.8.14

Size Driver

30KB

File Name

driver_release_notes.pdf

Observations

SUSE Linux Enterprise Server 11 (x86, x64, Intel Itanium2 and PowerPC 64-bit architectures)
New features, fixed issues and known issues in the driver (31 KB)

Release Notes
Date: March 2009 Product: Driver for Linux Version: 8.2.8.14 This document describes the new features, resolved known issues and current known issues associated with this driver build release. For the latest product documentation, go to www.Emulex.com. If you have any questions or require additional information, contact an authorized Emulex Corporation technical support representative.
New Features Driver for Linux 8.2.8.14
1. Supports the LP21000 and LP21002 FCoE adapters. (10 Gb/s capable) 2. Supports the LPe1250, LPe1252, LPe12000 and LPe12002 adapters. (2, 4 and 8 Gb/s capable) 3. Supports the latest HBAnyware utility version 4.1 as part of the master kit. Refer to the HBAnyware Utility User Manual for more information. 4. Supports SuSE Linux Enterprise Server 11. (Intel x86, Intel Itanium2, Intel EM64T, AMD64, and PowerPC 64-bit architectures) 5. Adds interfaces via the sysfs file system to update speed and topology parameters without requiring link bounce. 6. Supports Power Management Suspend/Resume operations. 7.
Resolved Issues in Driver for Linux 8.2.8.14
Supports MSI-X interrupt handling.
Known Issues in Driver for Linux 8.2.8.14
There are no resolved issues in this driver version.
1. PCI Hot Plug may cause applications to malfunction Performing a PCI Hot Plug may cause the HBAnyware utilities or third party applications that use the Emulex libraries (i.e. HBAAPI) to behave unpredictably or malfunction. Workaround: 1. Stop all applications that are accessing LPFC's HBAAPI interface (HBAnyware utilities or third party applications) before performing PCI Hot Plug of an LPFC HBA. Use the following command to stop the HBAnyware application: #/usr/sbin/hbanyware/stop_hbanyware 2. Perform the PCI Hot Plug of the HBA. 3. Restart the application.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

HBAnyware Manual

Information

VMware ESX

Operating System

Manual

Version

7.3.2

Size Driver

3.9MB

File Name

hbanyware34_preliminary.pdf

Observations

ESX 3.02, ESX 3.0.1, ESX 3.0. lpfc Driver 7.3.2_vmw (All) is embedded in the VMware releases
HBAnyware Utility User Manual

Introduction.............................................................................................................. 1
Known Issues .................................................................................................... 2
Installing HBAnyware Components.......................................................................... 2
Installing the HBAnyware Utility......................................................................... 2
Installing the HBAnyware Utility with Web Launch............................................. 4
Installing the HBAnyware Utility Security Configurator ...................................... 5
Uninstalling the HBAnyware Security Configurator............................................ 6
Uninstalling HBAnyware Web Launch Only ....................................................... 7
Uninstalling the Utility Package ......................................................................... 7
Using the HBAnyware Components......................................................................... 8
Starting the HBAnyware Utility........................................................................... 8
Starting HBAnyware with Web Launch .............................................................. 8
Starting the HBAnyware Security Configurator .................................................. 9
Starting HBAnyware from the Command Line ................................................... 9
Examples of Modifications .................................................................. 10
The HBAnyware Utility Window Element Definitions ....................................... 10
The Menu Bar ........................................................................................... 11
The Toolbar ............................................................................................... 11
The Toolbar Buttons .................................................................................. 11
Sort Toolbar Buttons ........................................................................... 11
The Discovery-Tree................................................................................... 12
Discovery-Tree Icons .......................................................................... 12
Property Tabs............................................................................................ 13
Status Bar ................................................................................................. 13
Changing Management Mode ......................................................................... 13
Resetting HBAs ............................................................................................... 14
Changing HBA Names .................................................................................... 15
Discovering HBAs ........................................................................................... 16
Automatic Fibre Channel Discovery .......................................................... 16
Remote SAN Management Using TCP/IP Access Protocol....................... 16
Adding a Single Host .......................................................................... 17
Adding a Range of Hosts .................................................................... 18
Removing Hosts.................................................................................. 19
Configuring Discovery Settings ................................................................. 19
Sorting HBA Information.................................................................................. 20
Viewing Remote and Local HBAs.............................................................. 20
Viewing HBA Information................................................................................. 21
Viewing Discovery Information .................................................................. 21
Viewing Host Information .......................................................................... 22
The Host Information Tab.................................................................... 22
The Driver Parameters Tab................................................................. 23
Viewing General HBA Attributes ............................................................... 24
Viewing Detailed HBA Information ............................................................ 26
Viewing Fabric Information........................................................................ 28
Viewing Target Information........................................................................ 29
Viewing LUN Information........................................................................... 30
Masking and Unmasking LUNs (Windows, Solaris LPFC and
Solaris SFS)........................................................................................ 31
Viewing Port Statistics............................................................................... 33
Viewing Firmware Information ................................................................... 35
Viewing Target Mapping (Windows, Solaris LPFC and Solaris SFS)......... 36
Viewing Target Mapping (Linux) ................................................................ 37

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

2.02e

Size Driver

417KB

File Name

linux202e.pdf

Observations

RHEL 3.0 Update 6 x86 (Intel), x86-64 (AMD and Intel) and IA64
Installation, Configuration and Troubleshooting (471 KB) Chapter 1 Introduction
Purpose of This Document ............................................................. 1-2
Related Documentation .................................................................. 1-2
Host Connectivity ............................................................................ 1-2
Director Bit Settings......................................................................... 1-3
Boot Device Support........................................................................ 1-3
Addressing........................................................................................ 1-3
Zoning ............................................................................................... 1-4
Useful Linux Utilities and Functions ............................................ 1-4
Chapter 2 Installing and Configuring the HBA and Driver
Installing the HBA........................................................................... 2-2
Updating the Flash Firmware/BIOS............................................. 2-3
Downloading the Emulex v2.x-Series HBA Driver for
the v2.4.x Kernel............................................................................... 2-5
What Next? ................................................................................ 2-5
Configuring the Host with the Emulex v2.x-Series HBA
Driver................................................................................................. 2-6
SuSE SLES 8 SP3 and the Emulex v2.02e Driver.................. 2-6
RHEL 2.1 and the Emulex v2.02e Driver............................. 2-10
RHEL 3.0 and the Emulex v2.02e Driver............................. 2-12
Recommended Changes to lpfc.conf ................................... 2-15
What Next? .............................................................................. 2-17
Enabling Persistent Binding ......................................................... 2-18
Obtaining Initiator and Target Information ....................... 2-18
Editing lpfc.conf...................................................................... 2-19
Editing /etc/modules.conf ................................................... 2-20
Additional Notes ........................................................................... 2-23
Linux Device-Naming Convention...................................... 2-23
Dynamic Device Reconfiguration: Procedures .................. 2-27
Dynamic Device Reconfiguration: Device Numbering .... 2-28
HPQ Server-Specific Note ..................................................... 2-29
(CLARiiON only) Required /etc/modules.conf Edit for
Red Hat Enterprise Linux 2.1 and 3.0 and SLES 8.0
Default Modular Kernels....................................................... 2-30
(CLARiiON only) Linux Naviagent Limitation with
fdisk on CLARiiON................................................................ 2-33
(CLARiiON only) Linux Naviagent Limitation with
VERITAS Volume Manager v3.2 on CLARiiON ............... 2-35
(CLARiiON only) Linux Naviagent Requirement for
Intel Itanium Systems on CLARiiON.................................. 2-36
(CLARiiON only) Passive-Not-Ready/ FailOverMode SP
Bit Setting and Spinning Up Devices................................... 2-37
Incorporating EMC Fibre Channel.............................................. 2-39
Review the EMC Support Matrix for the latest information on
approved HBAs and drivers.
? Purpose of This Document ...............................................................1-2
? Related Documentation.....................................................................1-2
? Host Connectivity ..............................................................................1-2
? Director Bit Settings ...........................................................................1-3
? Boot Device Support..........................................................................1-3
? Addressing..........................................................................................1-3
? Zoning..................................................................................................1-4
? Useful Linux Utilities and Functions ..............................................1-4

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Windows 2003-2008

Operating System

Manual

Version

2.20.006

Size Driver

4.1MB

File Name

win.pdf

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Offline Utility Manual

Information

Manual

Operating System

Manual

Size Driver

491KB

File Name

manual.pdf

Observations

EMC qualifies operation of the hardware, drivers, firmware and Boot Bios for the products referenced, as documented in the current EMC ESM (EMC Support Matrix). Utility software, including HBAnyware and various stand alone utilities used to manage or maintain Emulex products, are not tested by EMC. Utility software is provided for the convenience of EMC customers. Emulex is responsible for the integrity, functionality and support.
WARNING: You are about to download the EMC Approved HBA driver. This driver is optimized for use with EMC "-E" HBAs. It is being made available to you to update your approved EMC HBAs to support your EMC and non-EMC hardware environments. Downloading this EMC approved driver for use with an unqualified or unsupported HBA may be inconsistent with applicable terms and conditions. If you have any questions about the suitability of downloading this driver, contact your Emulex or EMC sales team.

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Linux User Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.0.16.47

Size Driver

971KB

File Name

linux.pdf

Observations

Asianux 2.0 SP2 and later (x86, x64, Intel Itanium2 and PowerPC 64-bit architectures)
Driver for Linux User Manual

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 1
For the LPFC Driver Kit............................................................................... 1
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 2
Known Issues.................................................................................................... 2
Installing the Driver Kit ............................................................................................ 2
Driver Kit Install Script Options.......................................................................... 3
Driver Kit Directory Structure ............................................................................. 3
Installing the Driver on Unsupported Linux Distributions.......................................... 3
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 4
Installing the Driver Kit into an Upgraded Kernel ............................................... 4
Installing the Utilities and the Application Helper Module......................................... 4
Prerequisites ............................................................................................... 4
Procedure ................................................................................................... 5
Utilities Directory Structure.......................................................................... 5
Installing the HBAnyware Utility with Web Launch............................................. 6
Prerequisites ............................................................................................... 6
Procedure ................................................................................................... 6
Installing the HBAnyware Security Configurator ................................................ 7
Prerequisites ............................................................................................... 7
Procedure ................................................................................................... 7
Installing the HBAnyware Utility and the Application Helper Module
using the Upgrade Kernel Option ..................................................................... 7
Prerequisites ............................................................................................... 7
Procedure ................................................................................................... 7
Uninstalling the Driver Kit .................................................................................. 8
Uninstalling a Previous Application Helper Module
(Stand Alone Kit) ............................................................................................... 9
Uninstalling the Utilities ........................................................................................... 9
Uninstalling the HBAnyware Security Configurator............................................ 9
Uninstalling HBAnyware Web Launch only...................................................... 10
Uninstalling the HBAnyware Utility and the Application Helper Module ........... 10
Configuration ........................................................................................11
Driver Configuration Methods using modprobe and
/etc/modprobe.conf.......................................................................................... 11
Temporary Configuration Method .............................................................. 11
Persistent Configuration Method ............................................................... 11
Creating a New Ramdisk Image ...................................................................... 12
For Installed LPFC Driver Kits................................................................... 12
For Distribution In-Box LPFC Drivers ........................................................ 13
Temporary Driver Configuration by Read/Write to sysfs .................................. 13
Dynamically Adding LUNs and Targets............................................................ 14
Driver Parameters Reference Table ................................................................ 14
Using udev for Persistent Naming ................................................................... 17

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Windows 2003

Operating System

Manual

Version

1.20a3

Size Driver

3.7MB

File Name

manual.pdf

Observations

Qualification: Microsoft WHQL Qualified 32-bit Windows Server 2003, 64-bit Windows Server 2003 and Windows Server 2003 x64 Edition.
Note For Windows 2003 configurations running STORPort drivers Microsoft STORPort hotfix Q916048 is required.
Refer to EMC Knowledgebase ID emc135768 for further information.
Installation, Configuration and Troubleshooting

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Windows 2003

Operating System

Manual

Version

1.11a3

Size Driver

4.1MB

File Name

win.pdf

Observations

Qualification: Microsoft WHQL Qualified 32-bit Windows Server 2003, 64-bit Windows Server 2003 and Windows Server 2003 x64 Edition.
Note For Windows 2003 configurations running STORPort drivers Microsoft STORPort hotfix Q916048 is required.
Refer to EMC Knowledgebase ID emc135768 for further information.
Installation, Configuration and Troubleshooting (2,918 KB) Chapter 1 Installation and Configuration
How this guide works...................................................................... 18
Downloading latest Emulex drivers/firmware/BIOS
files ............................................................................................... 18
Installing the adapter ....................................................................... 20
Matching the adapter with the correct PCI slot .................... 22
Fibre Channel over Ethernet (FCoE) .............................................. 27
Booting from the external storage array........................................ 28
Updating the flash firmware/BIOS ........................................ 28
Emulex LightPulse-based Fibre Channel adapter
BIOS/boot LUN settings .......................................................... 36
Installing a RAMDISK under the EFI shell ............................ 76
Installing Windows on an external SAN disk using an EFI
RAMDISK .......................................................................................... 77
Windows 2000/2003 external boot disk installation ............ 77
Windows 2008 internal/external boot disk installation ...... 84
Windows 2008 Server Core operating system option.................. 94
Limitations.................................................................................. 95
EMC support .............................................................................. 95
Installing adapter driver and software utilities............................ 97
Pre-installation guidelines........................................................ 97
Installing or upgrading the driver and utilities .................... 98
Updating the adapter firmware using the HBAnyware
utility ......................................................................................... 107
Adapter BIOS upgrade................................................................... 111
Fibre Channel over Ethernet (FCoE) Converged Network
Adapter (CNA) procedures........................................................... 115
Overview .................................................................................. 115
Installing Fibre Channel firmware on an Emulex CNA.... 118
Installing Menlo firmware on an Emulex CNA.................. 124
Installing or upgrading the driver and utilities on an
Emulex OCe10102-FM CNA.................................................. 130
Updating adapter firmware on an Emulex OCe10102-FM
CNA........................................................................................... 137
Configuring Emulex OneConnect FCoE BIOS/boot LUN
settings for OCe10102-FM CNA adapters ........................... 144
Establishing connectivity to the storage array ........................... 154
Verifying connectivity to the storage array................................. 155
Starting HBAnyware for Windows ...................................... 155
Starting device manager for Windows................................. 157
Starting disk management for Windows ............................. 157
Starting PowerPath GUI for Windows................................. 158
Installing additional Navisphere Host Agent software ............ 160
Emulex NPIV solution ................................................................... 162
Chapter 2 Miscellaneous Planning and Procedures

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Windows 2000-2003

Operating System

Manual

Version

1.03a9 x86, IA64 and x64

Size Driver

4.1MB

File Name

win.pdf

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Installation, Configuration and Troubleshooting (2,918 KB) Chapter 1 Installation and Configuration
How this guide works...................................................................... 18
Downloading latest Emulex drivers/firmware/BIOS
files ............................................................................................... 18
Installing the adapter ....................................................................... 20
Matching the adapter with the correct PCI slot .................... 22
Fibre Channel over Ethernet (FCoE) .............................................. 27
Booting from the external storage array........................................ 28
Updating the flash firmware/BIOS ........................................ 28
Emulex LightPulse-based Fibre Channel adapter
BIOS/boot LUN settings .......................................................... 36
Installing a RAMDISK under the EFI shell ............................ 76
Installing Windows on an external SAN disk using an EFI
RAMDISK .......................................................................................... 77
Windows 2000/2003 external boot disk installation ............ 77
Windows 2008 internal/external boot disk installation ...... 84
Windows 2008 Server Core operating system option.................. 94
Limitations.................................................................................. 95
EMC support .............................................................................. 95
Installing adapter driver and software utilities............................ 97
Pre-installation guidelines........................................................ 97
Installing or upgrading the driver and utilities .................... 98
Updating the adapter firmware using the HBAnyware
utility ......................................................................................... 107
Adapter BIOS upgrade................................................................... 111
Fibre Channel over Ethernet (FCoE) Converged Network
Adapter (CNA) procedures........................................................... 115
Overview .................................................................................. 115
Installing Fibre Channel firmware on an Emulex CNA.... 118
Installing Menlo firmware on an Emulex CNA.................. 124
Installing or upgrading the driver and utilities on an
Emulex OCe10102-FM CNA.................................................. 130
Updating adapter firmware on an Emulex OCe10102-FM
CNA........................................................................................... 137
Configuring Emulex OneConnect FCoE BIOS/boot LUN
settings for OCe10102-FM CNA adapters ........................... 144
Establishing connectivity to the storage array ........................... 154
Verifying connectivity to the storage array................................. 155
Starting HBAnyware for Windows ...................................... 155
Starting device manager for Windows................................. 157
Starting disk management for Windows ............................. 157
Starting PowerPath GUI for Windows................................. 158
Installing additional Navisphere Host Agent software ............ 160
Emulex NPIV solution ................................................................... 162
Chapter 2 Miscellaneous Planning and Procedures

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Manual

Information

Windows 2000

Operating System

Manual

Version

2.42a0

Size Driver

4.1MB

File Name

win.pdf

Observations

Microsoft WHQL Qualified for Windows 2000 Server
Installation, Configuration and Troubleshooting (2,918 KB pdf file) Chapter 1 Installation and Configuration
How this guide works...................................................................... 18
Downloading latest Emulex drivers/firmware/BIOS
files ............................................................................................... 18
Installing the adapter ....................................................................... 20
Matching the adapter with the correct PCI slot .................... 22
Fibre Channel over Ethernet (FCoE) .............................................. 27
Booting from the external storage array........................................ 28
Updating the flash firmware/BIOS ........................................ 28
Emulex LightPulse-based Fibre Channel adapter
BIOS/boot LUN settings .......................................................... 36
Installing a RAMDISK under the EFI shell ............................ 76
Installing Windows on an external SAN disk using an EFI
RAMDISK .......................................................................................... 77
Windows 2000/2003 external boot disk installation ............ 77
Windows 2008 internal/external boot disk installation ...... 84
Windows 2008 Server Core operating system option.................. 94
Limitations.................................................................................. 95
EMC support .............................................................................. 95
Installing adapter driver and software utilities............................ 97
Pre-installation guidelines........................................................ 97
Installing or upgrading the driver and utilities .................... 98
Updating the adapter firmware using the HBAnyware
utility ......................................................................................... 107
Adapter BIOS upgrade................................................................... 111
Fibre Channel over Ethernet (FCoE) Converged Network
Adapter (CNA) procedures........................................................... 115
Overview .................................................................................. 115
Installing Fibre Channel firmware on an Emulex CNA.... 118
Installing Menlo firmware on an Emulex CNA.................. 124
Installing or upgrading the driver and utilities on an
Emulex OCe10102-FM CNA.................................................. 130
Updating adapter firmware on an Emulex OCe10102-FM
CNA........................................................................................... 137
Configuring Emulex OneConnect FCoE BIOS/boot LUN
settings for OCe10102-FM CNA adapters ........................... 144
Establishing connectivity to the storage array ........................... 154
Verifying connectivity to the storage array................................. 155
Starting HBAnyware for Windows ...................................... 155
Starting device manager for Windows................................. 157
Starting disk management for Windows ............................. 157
Starting PowerPath GUI for Windows................................. 158
Installing additional Navisphere Host Agent software ............ 160
Emulex NPIV solution ................................................................... 162
Chapter 2 Miscellaneous Planning and Procedures

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Linux User Manual

Information

Linux 2.6 Kernel

Operating System

Manual

Version

8.2.8.14

Size Driver

1.6MB

File Name

manual.pdf

Observations

SUSE Linux Enterprise Server 11 (x86, x64, Intel Itanium2 and PowerPC 64-bit architectures)
Driver for Linux User Manual (1.64 MB pdf file)

Installation ...............................................................................................1
Driver Information .................................................................................................... 1
Supported Features........................................................................................... 1
New Features in this Release............................................................................ 1
Prerequisites ..................................................................................................... 2
For the lpfc Driver Kit .................................................................................. 2
Compatibility...................................................................................................... 2
Things to Know Before You Download .............................................................. 3
Known Issues .................................................................................................... 3
Installing the Driver Kit ............................................................................................ 3
Driver Kit Install Script Options.......................................................................... 4
Driver Kit Directory Structure ............................................................................. 4
Installing the Driver on Unsupported Linux Distributions.......................................... 5
Upgrading the Kernel or Applying a Distribution Service Pack or Update ................ 5
Installing the Driver Kit into an Upgraded Kernel ............................................... 5
Booting From a Non-Zero LUN Attached to an Emulex Adapter .............................. 6
Installing the HBAnyware Utility ............................................................................... 6
Uninstalling the Driver Kit .................................................................................. 7
Configuration ..........................................................................................8
Driver Configuration Methods Using modprobe and
/etc/modprobe.conf............................................................................................ 8
Temporary Configuration Method ................................................................ 8
Persistent Configuration Method ................................................................. 8
Temporary Driver Configuration by Read/Write to sysfs .................................... 9
Creating a New Ramdisk Image ...................................................................... 10
For Installed lpfc Driver Kits ...................................................................... 10
For Distribution In-Box lpfc Drivers............................................................ 10
Dynamically Adding LUNs and Targets............................................................ 10
Driver Parameters Reference Table ................................................................ 11
Using udev for Persistent Naming ................................................................... 15
Using udev to Discover Logical to Physical Mappings for sd Devices ....... 15
Configuring the System to Boot From SAN Using Persistent Names ........ 15
Using udev with st Devices ....................................................................... 16
Further Information About Persistent Names ............................................ 17
Working with Virtual Ports (vports)......................................................................... 18
Creating, Deleting and Displaying vports......................................................... 18
The mkvport.sh Script ............................................................................... 18
The rmvport.sh Script................................................................................ 19
The lsvport.sh Script ................................................................................. 19
The vport Sysfs Tree ....................................................................................... 19
Driver Version 8.2.8.14 sysfs Structure............................................................ 20
Vport sysfs Entries .................................................................................... 21
Vport Configuration Limits ............................................................................... 23
DHCHAP Authentication and Configuration ........................................................... 24
Authentication Configuration Parameters ........................................................ 25
Setting Remote and Local Passwords ............................................................. 25

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

DOS Offline Utility

Operating System

MS-DOS

Version

2.0a5

Size Driver

100KB

File Name

doslpcfg_2.0a6.zip

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Applications Kit

Operating System

VMware ESX

Version

7.4.0.41

Size Driver

931KB

File Name

elxvmwarecorekit-esx35-4.0a45-1.i386.rpm

Observations

Virtual Infrastructure 3 v3.5 (ESX 3.5 U4, Virtual Center 2.5) - 10 Gb/s CNAs
The ESX 3.5 U2 lpdf Driver Version 7.4.0.41 is embedded in the VMware release.
HBAnyware 4.0a45 agent, hbacmd, HP Rubah library version 9.0 (932 KB rpm file)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

AutoPilot Install Kit

Operating System

Windows 2000-2003

Version

1.11a0 x86, IA64 and x64

Size Driver

15MB

File Name

storportminiportkit_1-11a0-1c.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver 64-bit

Operating System

Windows 2000-2003

Version

1.02a3

Size Driver

6.7MB

File Name

storport-6-1.02a3-2b.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.0a13 and lputil64 version 1.7a16

This kit contains the following components:

elxstorinstall6102a3dc.zip - Emulex Fibre Channel StorPort Miniport Driver
Emlx64Apps300a5.zip - Emulex Applications kit
Readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the elxstorinstall6102a3dc.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.doc file contained in the
Emlx64Apps300a5.zip package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver

Operating System

Windows 2000-2003

Version

1.03a9 x86, IA64 and x64

Size Driver

11.2MB

File Name

storport-5-1.03a9-1d.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.1a9 and lputilnt version 1.8a2

This kit contains the following components:

elxstorinstall5103a9dc.zip - Emulex Fibre Channel Storport Miniport Driver
EmlxApps21a9-1b.zip - Emulex Applications Kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
relnotes.doc file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver 32-bit

Operating System

Windows 2000-2003

Version

1.02a3

Size Driver

5.6MB

File Name

storport-5-1.02a3-1b.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.0a13 and lputil64 version 1.7a16

This kit contains the following components:

elxstorinstall5102a3c.zip - Emulex Fibre Channel StorPort Miniport Driver
EmlxApps300a5.zip - Emulex Applications kit
Readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
readme.txt file included in the elxstorinstall5102a3c.zip package.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.doc file contained in the
EmlxApps300a5.zip package.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Legacy Install Kit x86

Operating System

Windows 2000-2003

Version

1.11a0 x86, IA64 and x64

Size Driver

12.6MB

File Name

storport-5-1.11a0-1e.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.1a17 and elxcfg version 1.41a17

This kit contains the following components:

elxstorinstall5111a0c.zip - Emulex Fibre Channel Storport Miniport Driver
EmlxApps21a17-1b.zip - Emulex Applications Kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
relnotes.doc file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Legacy Install Kit IA64

Operating System

Windows 2000-2003

Version

1.11a0 x86, IA64 and x64

Size Driver

12.9MB

File Name

storport-6-1.11a0-1c.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.1a17 and elxcfg version 1.41a17

This kit contains the following components:

elxstorinstall6111a0dc.zip - Emulex Fibre Channel Storport Miniport Driver
EmlxApps21a17-1b.zip - Emulex Applications Kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
relnotes.doc file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Legacy Install Kit x64

Operating System

Windows 2000-2003

Version

1.11a0 x86, IA64 and x64

Size Driver

12.6MB

File Name

storport-7-1.11a0-1e.zip

Observations

Qualification: Microsoft WHQL Qualified for Windows 2000 Server and 32-bit Windows Server 2003
Note This driver requires hot fix Q903081 for SP1 and non-SP1 Windows 2003 configurations including x86, x64, and IA64.
Base driver, HBAnyware utility 2.1a17 and elxcfg version 1.41a17

This kit contains the following components:

elxstorinstall7111a0c.zip - Emulex Fibre Channel Storport Miniport Driver
EmlxApps21a17-1b.zip - Emulex Applications Kit
readme.first.txt - this file

The detailed contents for each of these components can be found in
the readme files included in each individual kit. The specific minimum
system requirements for each of these kits can be found in the same files.

It is important that the components of this kit be installed in the
appropriate order:

1) The driver kit must be installed first, followed by the applications
kit. Instructions for installing the driver kit can be found in the
relnotes.doc file included in the Emulex Driver Kit listed above.

2) Once the driver has been successfully installed, then the applications
kit must be installed. Instructions for installing the applications
kit can be found in the readme.pdf file contained in the Emulex
Applications Kit listed above.

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

AutoPilot Install Kit

Operating System

Windows 2003

Version

1.20a3

Size Driver

19MB

File Name

storportminiportkit_1-20a3-1h.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

AutoPilot Install Kit

Operating System

Windows 2003

Version

1.30a6

Size Driver

24MB

File Name

emcstorportminiportkit_1-30a6-1b.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

AutoPilot Install Kit

Operating System

Windows 2003

Version

1.30a9

Size Driver

24.2MB

File Name

emcstorportminiportkit_1-30a9-1e.exe

Observations

Qualification: Microsoft WHQL Qualified 32-bit Windows Server 2003, 64-bit Windows Server 2003 and Windows Server 2003 x64 Edition.
Note For Windows 2003 configurations running STORPort drivers Microsoft STORPort hotfix KB943545 is required.
Base driver, HBAnyware utility 3.1a8 and lputilnt version 1.8a18 (24.6 MB exe file)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

AutoPilot Install Kit

Operating System

Windows 2003

Version

1.11a3

Size Driver

15.1MB

File Name

storportminiportkit_1-11a3-1b.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Windows 2003

Version

2.01a4

Size Driver

8.8MB

File Name

storportminiportkit_2-01a4-1g.exe

Observations

Qualification: The Storport Miniport driver is WHQL qualified for the Microsoft "Designed for Windows" logo program and digitally signed for x86, Itanium and x64 Editions versions of Windows Server 2003 and Windows Server 2003 Datacenter Edition.
Note Windows Server 2003 SP1 or SP2 and the KB943545 update to the Microsoft Storport driver are required. The KB943545 update must be applied before the Emulex Storport Miniport driver version 2.01a4 can be installed.
Driver 2.01a4 can be used to new install new Boot from SAN configurations with SP2. After the installation completes and the system reboots, install STORPort hotfix Q943545. The HBAnyware management application can be installed with the full Storport Miniport kit or by manually installing the Emulex PLUS driver and the driver utilities package.
Driver 2.01a4 cannot be used to directly install new Boot from SAN configurations with SP1. With SP1, new Boot from SAN configurations require the initial installation to be done with driver 1.30a9. Once the OS is installed, then upgrade to SP2 and STORPort hotfix Q943545 before upgrading to driver 2.01a4.
Base driver, HBAnyware utility 3.4a9 (9.21 MB exe file)

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Windows 2003-2008

Version

2.10a7

Size Driver

11.6MB

File Name

storportminiportkit_2-10a7-1e.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Core Installation Driver Kit

Operating System

Windows 2003-2008

Version

2.10a7

Size Driver

2.8MB

File Name

storportminiportcorekit_2-10a7-1e.exe

Observations

Company

Emulex

Categories

Networks Cards

Serie

Emulex Products Emulex for EMC

Model

Emulex 30p-35p HP 2Gb-s Mezz Card

Description

Driver Kit

Operating System

Windows 2003-2008

Version

2.20.006

Size Driver

37.1MB

File Name

storportminiportkit_2.20.006-1h.exe

Observations

Access to Official Website Emulex

Home English Drivers English

Welcome to the HelpDrivers, driver for printers.

Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more

You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.

Do not rename the file you're downloading, it may cause installation problems.

Available 91 files for Emulex 30p-35p HP 2Gb-s Mezz Card

Select Files