Foxconn 915M03-G-8EKRS2 Download Drivers, Manual and BIOS

Silicon Image SiI 3112 SATARAID Controller OS Driver Installation
----------------------------------------

Table of Contents
----------------------------------------

1) Windows NT 4.0 and Windows 2000/XP Fresh Installation.

2) Adding the SiI RAID controller to an existing Windows NT installation.

3) Adding the SiI RAID controller to an existing Windows 2000/XP installation.

4) Verifying controller installation under Windows NT, 2000 and XP.

5) Update SiI RAID driver on Windows NT 4.0 with existing Silicon Image driver.

6) Update SiI RAID driver on Windows 2000/XP with existing Silicon Image driver.

7) Windows 98SE and Windows Me Fresh Installation Instructions.

8) First time installing SiI RAID driver with existing Windows 98SE/Me.

9) Update SiI RAID driver on Windows 98SE/Me with existing Silicon Image driver.

REALTEK RTL Gigabit and Fast Ethernet NIC Driver Setup Utility for Foxconn 915M03-G-8EKRS2
Windows Me/2000/XP NDIS Driver

======================

How to use this RTLSetup Utility
----------------------------------------
Install Foxconn 915M03-G-8EKRS2 in Windows Me:

1. If the Operating System's New Hardware Wizard prompts you that
"New Hardware Found" for the "PCI Ethernet Controller", you should
click "Next" until "Finish" is clicked and without specifying
location of the driver. You will see the "PCI Ethernet Controller"
in the Device Manager.

2. Then you can install or update the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

You need to reboot the system immediately after the Install shield
completes the installation/upgrade.

3. Do not click "Cancel" during New Hardware Wizard searches for the
driver.

4. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately.

Install Foxconn 915M03-G-8EKRS2 in Windows 2000 and XP:

1. If the Operating System's Found New Hardware Wizard prompts you that
"New Hardware Found" for the "Ethernet Controller", you should click
"Next" until "Finish" is clicked and without specifying location of
the driver. You will see the "Ethernet Controller" in the Device
Manager.

2. Then you can install or upgrade the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

3. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately if you want your networking to be re-installed.

Intel on board audio drivers for 32 bit

* Product: Intel(R) Chipset Software Installation Utility
* Release: Production Candidate
* Version: 5.00.1003
* Target Chipset#: Intel(R) Springdale G Chipset

*********************************************************

* CONTENTS OF THIS DOCUMENT
*********************************************************
This document for Foxconn 915M03-G-8EKRS2 contains the following sections:

1. Overview
2. System Requirements
3. Contents of the Distribution Package
4. List of Available Command Line Flag Options
5. Contents of the Extracted Files
6. Installing the Software for Foxconn 915M03-G-8EKRS2 in Interactive Mode
7. Installing the Software for Foxconn 915M03-G-8EKRS2 in Silent Mode
8. Installing the INF Files Prior to OS Installation
8A. Installing the Windows* 2000 INF Files Prior
to OS Installation
8B. Installing the Windows* 98SE/Windows* Me
INF Files Prior to OS Installation
9. Installing the INF Files After OS Installation
9A. Installing the Windows* 2000 INF Files after
OS Installation
9B. Installing the Windows* 98SE/Windows* Me INF Files
after OS Installation
10. Verifying Installation of the Software and
identifying the Software Version Number
11. Troubleshooting

DRIVER Production Version /nt5

This document for Foxconn 915M03-G-8EKRS2 contains the following sections:

1. System Requirements
2. Localized Language Abbreviations
3. Installing the Software for Foxconn 915M03-G-8EKRS2
4. Verifying Installation of the Software
5. Identifying the Software Version Number
6. Un Installing the Software for Foxconn 915M03-G-8EKRS2
7. Installation Switches Available

Chapter 1 Foxconn 915M03-G-8EKRS2 Product Introduction
Main Features . 2
Motherboard Layout . 4
Rear Panel Connectors . 5
Chapter 2 Foxconn 915M03-G-8EKRS2 Installation Instructions
CPU. 8
Memory . 11
Power Supply . 13
Other Connectors . 14
Expansion Slots . 18
Jumpers . 19

Chapter 3 Foxconn 915M03-G-8EKRS2 BIOS Description

Enter BIOS Setup . 23
Main Menu . 23
Standard CMOS Features . 25
BIOS Features . 28
Advanced BIOS Features . 29
Advanced Chipset Features . 33
Integrated Peripherals . 37
Power Management Setup . 41
PnP/PCI Configurations . 45
PC Health Status . 46
Frequency/Voltage Control . 47
Load Fail-Safe Defaults . 48
Load Optimized Defaults . 48
Set Supervisor/User Password . 48
Save & Exit Setup. 49
Exit Without Saving. 49

Chapter 4 Foxconn 915M03-G-8EKRS2 Driver CD Introduction

Utility CD content . 51
Start to install drivers. 52

Chapter 5 Foxconn 915M03-G-8EKRS2 Directions for Bundled Software

SuperStep. 54
SuperUpdate . 57
SuperLogo . 62
Chapter 6 Foxconn 915M03-G-8EKRS2 Special BIOS Functions

SuperBoot . 65
SuperBIOS-Protect . 66
SuperSpeed . 67
SuperRecovery . 68