Draytek Vigor2710 series Download Firmware

New Features
?? Support USB Disk Application (FTP/Samba).
?? “twodns” DDNS service.
?? Support PPPoA pass-through function.
?? Show source MAC address on Syslog for LAN toWAN packets.
?? Support Sierra 597 USB 3G Modem.
?? Add value for VPI/VCI (2/40) to Auto Detection table for Norway.
Improvement
?? Corrected: DTMF can't be detected when a DECT phone redials to PSTN phone.
?? Corrected: Dial Out Account can not be set to default on DialPlan Setup of WUI.
- 1 -
?? Corrected: If the phone is disabled but the phone state is not changed, the phone will not ring when receiving PSTN incoming call.
?? Corrected: When RFC-2833 with payload type= 96 packet is received, the router will reboot.
?? Corrected: SIP memory leakage.
?? Corrected: Problem of DECT phone ring after enabling the call barring block IP address.
?? Corrected: Call transfer failed for DECT phone.
?? Corrected: Problem of setting DECT play dial tone only when the account has been registered.
?? Corrected: Problem for semi-attendent CT for VoIP.
?? Corrected: Can not save DSL settings sometimes after finishing Auto Detection in Quick Start Wizard.
?? Corrected: Some problems occurred on WUI.
?? Corrected: Can not get TR069 parameters after meeting TR069 connection timeout.
?? Corrected: Firmware upgrade may be failed when upgraded by TR069.
?? Corrected: UCF can save 12 objects, only.
?? Corrected: Call filter malfunctioning.
?? Corrected: Failure of running IP Ping through PPTP of VPN.
?? Corrected: Problem of L2TP over IPSec for teleworker.
?? Corrected: Adding UPNP port mapping failed.
?? Corrected: Connection problem on PPTP NAT pass-through.
?? Improved: Prevent users from dialing 37-39 or 57-59 to DECT phone.
?? Improved: Wildcard '?' can be used in Digit Map.
?? Improved: Allowed VoIP number starting with # for non-IP calls.
?? Improved: Wireless interoperability with Vigor AP700 while using WDS with WPA or WPA2 mode.
?? Improved: Mouse cursor stays on the field of Username in Login page of Web UI.
?? Improved: Add/modify some TR069 parameters.
?? Improved: Router stability against NMAP scan.
?? Improved: Bridge mode may not work after powering off/on.
?? Improved: Add/modify some IM/P2P signatures.
?? Improved: Modify QoS command for usage and message display.
?? Improved: Remain ARP cache life settings to flash even reboot the router.
?? Improved: Increase compatibility with more stun servers.

Preface ...............................................................................................................1
1.1 Web Configuration Buttons Explanation ................................................................................. 1
1.2 LED Indicators and Connectors .............................................................................................. 2
1.2.1 For Vigor2710 ................................................................................................................... 2
1.2.2 For Vigor2710n ................................................................................................................. 4
1.2.3 For Vigor2710Vn............................................................................................................... 6
1.2.4 For Vigor2710VDn............................................................................................................ 8
1.3 Hardware Installation ............................................................................................................ 10
1.4 Printer Installation ..................................................................................................................11
Configuring Basic Settings ............................................................................17
2.1 Two-Level Management........................................................................................................ 17
2.2 Accessing Web Page ............................................................................................................ 17
2.3 Changing Password.............................................................................................................. 18
2.4 Quick Start Wizard ................................................................................................................ 20
2.4.1 Adjusting Protocol/Encapsulation ................................................................................... 21
2.4.2 PPPoE/PPPoA................................................................................................................ 22
2.4.3 1483 Bridged IP .............................................................................................................. 23
2.4.4 1483 Routed IP............................................................................................................... 24
2.5 Online Status......................................................................................................................... 25
2.6 Saving Configuration............................................................................................................. 27
User Mode Operation............................................................................................29
3.1 Internet Access...................................................................................................................... 29
3.1.1 Basics of Internet Protocol (IP) Network......................................................................... 29
3.1.2 PPPoE/PPPoA................................................................................................................ 30
3.2 LAN ...................................................................................................................................... 37
3.2.1 Basics of LAN ................................................................................................................. 37
3.2.2 General Setup................................................................................................................. 38
3.3 NAT ...................................................................................................................................... 41
3.3.1 Port Redirection .............................................................................................................. 41
3.3.2 DMZ Host........................................................................................................................ 43
3.3.3 Open Ports...................................................................................................................... 46
3.4 Applications ........................................................................................................................... 47
3.4.1 Dynamic DNS ................................................................................................................. 47
3.4.2 UPnP.............................................................................................................................. 49
3.5 VoIP...................................................................................................................................... 51

1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2710 ............................................................................................................... 2
1.1.2 For Vigor2710n ............................................................................................................. 4
1.1.3 For Vigor2710Vn........................................................................................................... 6
1.2 Package Content........................................................................................................................ 8
2. Installing Your Router........................................................................................... 9
2.1 Hardware Installation.................................................................................................................. 9
2.2 Printer Installation.....................................................................................................................11
3. Configuring Web Pages ..................................................................................... 17
3.1 Accessing Web Page ............................................................................................................... 17
3.2 Basic Configuration .................................................................................................................. 18
3.3 Wireless Configuration ............................................................................................................. 21
3.2.1 Basic Wireless LAN Concept ...................................................................................... 21
3.2.2 General Setup ............................................................................................................. 21
3.2.3 Security Settings ......................................................................................................... 23
4. Trouble Shooting ................................................................................................ 25
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 25
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 26
4.3 Pinging the Router from Your Computer .................................................................................. 28
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 29
4.5 Backing to Factory Default Setting If Necessary...................................................................... 30
4.6 Contacting Your Dealer ............................................................................................................ 31

Introduction
The Vigor2710 series features advanced bandwidth control mechanism such as IP-layer
QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable
access control and bandwidth management.
The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of
firewall policies easy. The CSM (Content Security Management) feature allows more
precise and efficient access control for URL/Web Content Filtering, IM (Instant
Messenger) and P2P (Peer to Peer) applications.
Vigor2710 supports up to 2 VPN tunnels using advanced protocols such as
IPSec/PPTP/L2TP/L2TP over IPSec with AES/DES/3DES for encryption and
MD5/SHA-1 for authentication.
Vigor2710 ‘n’ models comply with 802.11n Draft-n standards. They support
WEP/WPA/WPA2 encryption and MAC Address Control, Wireless LAN Isolation. The
Wireless Rate Control function can adjust the data rate of each wireless station (client).
Vigor2710 ‘V’ models provide two analogue phone connectors and one line port. It
supports multiple SIP registrars with high flexible configuration and call handing options.
In addition, Vigor2710 series supports USB interface for connecting USB printer to share
printer or USB storage device for sharing files. Vigor2710 series provides two-level
management to simplify the configuration of network connection. The user operation
allows user accessing into WEB interface via simple configuration. However, if users
want to have advanced configurations, they can access into WEB interface through
administration operation.

Installing Your Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1. Connect the ADSL interface to the external ADSL splitter with an ADSL line cable
for all models. For Vigor2710Vn, also connect Line interface to external ADSL
splitter.
2. Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer.
3. Connect the telephone sets with phone lines (for using VoIP function). For the model
without phone ports, skip this step.
4. Connect one end of the power adapter to the router’s power port on the rear panel,
and the other side into a wall outlet.
5. Power on the device by pressing down the power switch.
6. The system starts to initiate. After completing the system test, the ACT LED will
light up and start blinking.
Here, we take Annex A model as an example for describing hardware installation.