Available 2 files for Creatix CTX720

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX720

Description

Specification for CTX720

Information

Specification PDF

Operating System

Manual

Size Driver

965KB

File Name

ctx720_spec.pdf

Observations

CTX720_V.1 WLAN Mini Card
Product Specification
Description: The CTX720_V.1 WLAN Mini Card is a low profile highly integrated
cost-effective Wireless LAN USB 2.0 network interface controller that
integrates a USB 2.0 PHY, SIE (Serial Interface Engine), 8051 MCU,
a Wireless LAN MAC, and a Direct Sequence Spread
Spectrum/OFDM base band processor onto one chip.
Main Chips: RTL 8225 WLAN RF Transceiver,
RTL 8187B-GR Network Interface Controller
Features: - Complies with IEEE802.11a/b/g standards
- Integrated Wireless LAN MAC and Direct Sequence Spread
Spectrum/OFDM Base band Processor in one chip
- Processing Gain compliant with FCC
- Supports both transmit and receive Antenna Diversity
- Data rates of 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps
- IEEE 802.11g protection mechanisms for both RTS/CTS and CTSto-
self
- DSSS with DBPSK and DQPSK, CCK modulations and
demodulations supported with long and short preamble
- OFDM with BPSK, QPSK, 16QAM and 64QAM modulations coding
rate of 1/2, 2/2, and 3/4
- Fast receiver Automatic Gain Control (AGC) & antenna diversity
functions
- Complies with WMM, 802.11e, and CCX specifications
- Complies with 802.11h, 802.11i, 802.22j specification
- Hardware based IEEE 802.11i encryption/decryption engine,
including 64-bit/128-bit WEP, TKIP and AES
- Supports WPA and WPA2 security
- Advanced power saving mode when the LAN and wake-up function
are not used

Company

Creatix

Categories

Fax & Modem & ISDN

Model

Creatix CTX720

Description

Driver

Operating System

Windows Vista 32-64 bits

Size Driver

1.9MB

File Name

rtl8187b_1090_vista.zip

Observations

How to use this Set8187 Utility
-------------------------------
For Windows ME:

1. If the Operating System's New Hardware Wizard prompts you that
"New Hardware Found" for the "PCI Ethernet Controller", you should
click "Next" until "Finish" is clicked and without specifying
location of the driver. You will see the "PCI Ethernet Controller"
in the Device Manager.

2. Then you can install or update the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

You need to reboot the system immediately after the Install shield
completes the installation/upgrade.

3. Do not click "Cancel" during New Hardware Wizard searches for the
driver.

4. You can remove Set8187 utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately.

For Windows 2000/XP:

1. If the Operating System's Found New Hardware Wizard prompts you that
"New Hardware Found" for the "Ethernet Controller", you should click
"Next" until "Finish" is clicked and without specifying location of
the driver. You will see the "Ethernet Controller" in the Device
Manager.

2. Then you can install or upgrade the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

3. You can remove Set8187 utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately if you want your networking to be re-installed.