Iwill SIde DU3160 Download Drivers

This release has been tested with DOS 6.0 and all available
versions and service packs as of this date.

Note: Before installation, make a backup copy of the QLogic
Software Diskette.

This document is divided into 3 Sections

Section 1 DOS files on this disk
Section 2 DOS Installation
Section 3 Troubleshooting

Section 1 DOS files on this disk
---------------------------------

The following files on this disk support DOS 6.0 and above:

QL26ASPI.SYS - DOS SCSI Driver including ASPI support.

QL00CDRM.SYS - DOS Driver that allows support for CD-ROM devices.

INSTALL.BAT - This is the batch file you execute to install the
DOS Drivers.

README.TXT - This file.

Note: The remaining files in the root directory of this disk are
support files for the QLogic utilities.

Section 2 DOS Installation
---------------------------

2.0 Installing DOS Drivers Using the Setup Utility

The DOS software drivers can be installed manually or by
using the Setup Utility.

The Install utility, is a menu-based utility for installing and
configuring your SCSI, ASPI, and CD-ROM drivers. It automatically
updates your CONFIG.SYS and AUTOEXEC.BAT files and creates a backup
copy of the original files with .OLD extension. Install runs under
version 6.0 or later of MS-DOS.

If you use the Setup program, you do not need to perform the
manual installation procedures in section 2.2

To use Setup, follow these steps.

1. Boot to DOS (not WinNT or Win9x).

2. Insert the QLogic diskette in an appropriate drive.

3. At the DOS prompt, type (drive letter):INSTALL followed by
the key.

Example:
A:INSTALL

4. Follow the screen prompts to access the README.TXT file or
Press to continue.

5. The system prompts "Will you be connecting a CD-ROM to your
system". Click on YES if you are connecting a SCSI CD-ROM
to the QLogic SCSI adapter.

6. Follow the directions displayed on the screen to complete the
installation process.

7. Press the key to exit the program. Remove the QLogic
software diskette from the drive AFTER you exit the program.

Contents
--------

1. OS Support
2. Supported Features
3. Release History
4. Creating the Driver Diskette
5. Installing the Driver
5.1. Fresh OS installation with the QLogic Controller as Boot
5.2. Adding the QLogic Controller to the Existing OS
5.3. Updating the existing QLogic Driver
6. Removing the Driver
7. Driver Parameters
8. Limitations
9. Additional Notes
10. Diskette Content
11. Contacting QLogic

======================================================================

1. OS Support
-------------

This release has been tested with Windows .NET/XP/2000 (x86).

======================================================================

2. Supported Features
---------------------

* Windows .NET/XP/2000 SCSI PnP interface
* Support for more than 8 LUNs (See Additional Notes)

======================================================================

3. Release History
------------------

Please refer to Release Notes.

======================================================================

4. Creating the Driver Diskette
-------------------------------

Locate the driver you want on the QLogic website and click "Link to
driver." When prompted "What would you like to do with this file?"
choose "Save this program to disk", then specify a temporary location
on a hard drive. Insert a blank diskette in the diskette drive. Run
the self-extracting file you just downloaded specifying A:\ for
"Unzip To Folder:".

======================================================================

5. Installing the Driver
------------------------

This section is divided into the following three sections.
1. Fresh OS installation with the QLogic Controller as Boot
2. Adding the QLogic Controller to the Existing OS
3. Updating the existing QLogic Driver

======================================================================

5.1 Fresh OS installation with the QLogic Controller as Boot
------------------------------------------------------------

Perform the following steps to initially install Windows on the
SCSI drive (boot disk) attached to the QLA12160 controller.

1. Start Windows installation procedure using the Setup
diskettes or CD.
2. If you are booting from the CD, press F6 if you see the message

This release has been tested with the following:

a. Windows 95 Retail Version.

b. Windows 95 OEM Service Release 2 (Build 950b).

c. Windows 98/ME Retail Version.
This document is divided into 4 Sections:

Section 1: Windows 9X/ME files on this diskette.

Section 2: Installation of Windows 9X/ME onto a SCSI disk.

Section 3: Adding a QLogic Adapter to an existing system.

Section 4: Miniport Driver Adapter Settings.

================================================
Section 1: Windows 9X/ME files on this diskette
================================================

The Win9x directory on this diskette contains the following files:

QL12160.INF Driver installation script for Windows 9X/ME.

QL12160.MPD Windows 9X/ME miniport driver for the QLogic
QLA12160 Ultra 160M PCI Dual SCSI Adapter and
QLA10160 Ultra 160M PCI SCSI Adapter.

QL12160.CAT Digital Signature Catalog file.

README.TXT This text file.

==========================================================
Section 2: Installation of Windows 9X/ME onto a SCSI disk
==========================================================

To initially install Windows 9X/ME on a SCSI disk and/or from
a CD-ROM attached to the QLogic PCI SCSI adapter:

2.1 For Windows 95 Retail Pack (General distribution, Build 950)
-----------------------------------------------------------------

1. Install QLogic SCSI Adapter and attach SCSI device(s).
2. Install DOS onto system boot disk.
3. If installing from CD-ROM attached to QLogic adapter,
install QLogic DOS drivers for supporting CD-ROM device and
the MSCDEX.EXE driver. (Refer to the README file in the root
directory of the "QLogic Software Drivers" diskette).
4. Boot to DOS, loading CD-ROM driver, then run the Windows 95 SETUP
program from the CD.
5. Once Win95 is loaded and operational, open the "My Computer"
icon, then open the "Control Panel" icon.
6. From the Control Panel window, open the "System" icon and
select "Device Manager" tab.
7. Listed under "Other devices", select "PCI SCSI Bus Controller"
and click on "Properties".
8. Select the "Driver" tab and click on "Change Driver".
9. Select "SCSI controllers" and click on "OK".
10. Insert the "QLogic Software Drivers" diskette and click on "Have Disk".
11. Enter "A:\Win9x" for path to QLogic driver and click "OK".
12. Select "QLA12160 Ultra 160M PCI Dual SCSI Adapter" and click "OK".
13. Click "OK" again to proceed with installing miniport driver.
14. Click "Cancel" in the dialog box that may say, "Windows cannot
determine if it can remove this device safely" (DO NOT "Test").

CAUTION: Clicking "TEST" may cause the system to hang. However,
restarting the system will result in normal operation.

This release has been tested with the following:

a. Windows 95 Retail Version.

b. Windows 95 OEM Service Release 2 (Build 950b).

c. Windows 98/ME Retail Version.
This document is divided into 4 Sections:

Section 1: Windows 9X/ME files on this diskette.

Section 2: Installation of Windows 9X/ME onto a SCSI disk.

Section 3: Adding a QLogic Adapter to an existing system.

Section 4: Miniport Driver Adapter Settings.

================================================
Section 1: Windows 9X/ME files on this diskette
================================================

The Win9x directory on this diskette contains the following files:

QL12160.INF Driver installation script for Windows 9X/ME.

QL12160.MPD Windows 9X/ME miniport driver for the QLogic
QLA12160 Ultra 160M PCI Dual SCSI Adapter and
QLA10160 Ultra 160M PCI SCSI Adapter.

QL12160.CAT Digital Signature Catalog file.

README.TXT This text file.

==========================================================
Section 2: Installation of Windows 9X/ME onto a SCSI disk
==========================================================

To initially install Windows 9X/ME on a SCSI disk and/or from
a CD-ROM attached to the QLogic PCI SCSI adapter:

2.1 For Windows 95 Retail Pack (General distribution, Build 950)
-----------------------------------------------------------------

1. Install QLogic SCSI Adapter and attach SCSI device(s).
2. Install DOS onto system boot disk.
3. If installing from CD-ROM attached to QLogic adapter,
install QLogic DOS drivers for supporting CD-ROM device and
the MSCDEX.EXE driver. (Refer to the README file in the root
directory of the "QLogic Software Drivers" diskette).
4. Boot to DOS, loading CD-ROM driver, then run the Windows 95 SETUP
program from the CD.
5. Once Win95 is loaded and operational, open the "My Computer"
icon, then open the "Control Panel" icon.
6. From the Control Panel window, open the "System" icon and
select "Device Manager" tab.
7. Listed under "Other devices", select "PCI SCSI Bus Controller"
and click on "Properties".
8. Select the "Driver" tab and click on "Change Driver".
9. Select "SCSI controllers" and click on "OK".
10. Insert the "QLogic Software Drivers" diskette and click on "Have Disk".
11. Enter "A:\Win9x" for path to QLogic driver and click "OK".
12. Select "QLA12160 Ultra 160M PCI Dual SCSI Adapter" and click "OK".
13. Click "OK" again to proceed with installing miniport driver.
14. Click "Cancel" in the dialog box that may say, "Windows cannot
determine if it can remove this device safely" (DO NOT "Test").

CAUTION: Clicking "TEST" may cause the system to hang. However,
restarting the system will result in normal operation.

Contents
--------

1. OS Support
2. Supported Features
3. Release History
4. Creating the Driver Diskette
5. Installing the Drivera
5.1. Fresh OS installation with the QLogic Controller as Boot
5.1.1. Installing Windows NT 4.0 from the CD-ROM
5.1.2. Installing Windows NT 4.0 from the diskettes
5.2. Adding the QLogic Controller to the Existing OS
5.3. Updating the existing QLogic Driver
6. Removing the Driver
7. Driver Parameters
7.1. System Parameters
7.2. NVRAM Parameters
8. Diskette Content
9. Contacting QLogic

======================================================================

1. OS Support
-------------

This release has been tested with Windows NT Version 4.00. Earlier
versions of NT are not supported.

======================================================================

2. Supported Features
---------------------

* Intel/Compaq PCI Hot Plug
* SCSI Diagnostic IOCTL support
* Support for 32 LUNs

======================================================================

3. Release History
------------------

Please refer to Release Notes.

======================================================================

4. Creating the Driver Diskette
-------------------------------

Locate the driver you want on the QLogic website and click "Link to
driver." If prompted "What would you like to do with this file?"
choose "Save this program to disk", then specify a temporary location
on a hard drive. Insert a blank diskette in the diskette drive. Run
the self-extracting file you just downloaded specifying A:\ for
"Unzip To Folder:".

======================================================================

5. Installing the Driver
------------------------

This section is divided into the following three sections:
1. Fresh OS installation with the QLogic Controller as Boot
2. Adding the QLogic Controller to the Existing OS
3. Updating the existing QLogic Driver