ICP GDT7628RN Download Drivers

Drivers and ICP RAID Console for NetWare 5 and 6 (For Netware 6.5 only up to SP3. For SP4 and newer please use the driver provided here

New install of NetWare 4.2, 5.0, 5.1 and 6.0
============================================
(Versions prior 4.2 are not supported by this driver)

Note: Before hard disks connected to the controller can be used they have to
be configured first in the setup tool which can be accessed on boot by
pressing Ctrl+G.
Fresh installation of NetWare 4.2 using GDTRX.HAM driver:
---------------------------------------------------------
- create a driver diskette from the ICP System CD
(simply copy all files and directories from \drivers\netware to a diskette)
- start the OS installation from the NetWare CD
(Note: NetWare 4.x CDs are NOT bootable. A bootable DOS partition with the
appropriate DOS drivers for the used CD-ROM is required)
- at the driver summary menu select modify drivers
- insert the driver diskette into drive A:
- press ENTER on the storage driver list
- press INS in the storage controller driver menu
- press F3 and change the path to A:\drivers\4xx then press Enter
- select the GDTRX.HAM driver
- continue the NetWare installation by following the screen prompts

If the system hangs after loading drivers use the following steps:
------------------------------------------------------------------
- at the driver summary menu select modify drivers
- note all listed drivers (these names are required later on)
- REMOVE ALL drivers from the list
- insert the driver diskette into drive A:
- press ENTER on the storage driver list
- press INS in the storage controller driver menu
- press F3 and change the path in A:\drivers\4xx then press Enter
- select the GDTRX.HAM driver
- afterwards add all drivers noted before
- continue the NetWare installation by following the screen prompts
Fresh installation of NetWare 5.0 using GDTRX.HAM driver:
---------------------------------------------------------
- IMPORTANT: The GDTRX.HAM driver depends on a later version of the
NWPA.NLM than the one shipped with the NetWare 5.0 CD.
Without the NWPA.NLM update, the GDTRX.HAM driver will fail to load.
The following procedure will allow to upgrade the NWPA.NLM on the
fly during OS installation.

- create a driver diskette from the ICP System CD
(simply copy all files and directories from \drivers\netware to a diskette)
- start the OS installation from the NetWare bootable CD
- the NetWare Install will eventually load a "Welcome" screen asking to
verify the startup directory (C:\NWSERVER)
- press Alt+F10 to exit the installation.
- at the NetWare console prompt, type "down" and press ENTER
(the installation exits to the boot drive's DOS prompt)
- insert the driver diskette into the A: drive
- if the NetWare startup directory is on drive C:, run A:\INSTALL\NWUPDATE.BAT,
otherwise create a subdirectory named NWUPDATE at the root of the boot drive
and copy all the files from A:\DRIVERS\5XX to this NWUPDATE subdirectory
- leave the NetWare 5.0 bootable CD in place, remove the driver diskette
- reboot the server
- after rebooting the server, the NetWare 5.0 Install will start again
- right after the Accept of the License Agreement screen, select the
"Continue with Existing Partition" option
- when installing a new server the following message may show up:
"Warning: A previously installed version of NetWare was detected in C:\NWSERVER.
If you choose to install a new server, all data on the existing server will be lost.
".

Driver and ICP RAID Console (ICPCON) for SCO* Openserver up to 5.06a (Image file to create a driver disk under DOS, Windows , etc.).

The ICP Driver for SCO OpenServer
---------------------------------

Creating a Driver Disk
======================
To create a driver disk from an image file simply start IWRITE,
with the name of the floppy drive that should be used and the
name of the image.

e.g. IWRITE A: SCO5X

creates the ICP OpenServer 5.x Driver Disk in floppy drive A:
A pre-formatted 1.44 MB floppy disk can be used as well as an unformatted one.
Please note that all data on the destination disk will be deleted.
IWRITE can be used under MS-DOS, Windows NT, Windows 95 and OS/2.
IWrite32 can be used under Windows NT / 2000 / XP.

If there are problems formatting or creating the floppy disk (e.g. under
Windows 95), please use a pre-formatted floppy disk and force IWRITE not
to format the media by setting the parameter '/F' ("IWRITE A: SCO5X /F").

To check the contents of an image file simply use 'type' on the file.

e.g. "type SCO5X.IMG"

Driver and ICPCON for SCO UnixWare up to 7.1.1.

The ICP Driver for Caldera Unixware
-----------------------------------

Creating a Driver Disk
======================
To create a driver disk from an image file simply start IWRITE,
with the name of the floppy drive that should be used and the
name of the image.

e.g. IWRITE A: UnixW7

creates the ICP Unixware 7 Driver Disk in floppy drive A:
A pre-formatted 1.44 MB floppy disk can be used as well as an unformatted one.
Please note that all data on the destination disk will be deleted.
IWRITE can be used under MS-DOS, Windows NT, Windows 95 and OS/2.
IWrite32 can be used under Windows NT / 2000 / XP.

If there are problems formatting or creating the floppy disk (e.g. under
Windows 95), please use a pre-formatted floppy disk and force IWRITE not
to format the media by setting the parameter '/F' ("IWRITE A: UnixW7 /F").

To check the contents of an image file simply use 'type' on the file.

e.g. "type UnixW7.IMG"

Driver for Windows* NT and ICP RAID Console (ICPCON) for ICP Cluster Controllers

[Identification]
OptionType = SCSI

[LanguagesSupported]
ENG

[Options]
"GDTSCSI" = gdtx

[OptionsTextENG]
"GDTSCSI" = "ICP GDT Disk Array Controller"

[MiniportDrivers]
gdtx = !SERVICE_KERNEL_DRIVER, "SCSI Miniport", !SERVICE_ERROR_NORMAL, 32, %SystemRoot%\System32\IoLogMsg.dll , 7

[Identify]
;
;
read-syms Identification

set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)

Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
;
;
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}

;
; Check if the language requested is supported
;
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
goto returnoptions
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif

;
; form a list of all the options and another of the text representing
;

returnoptions = +
set OptionList = ^(Options, 0)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL

finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)

ICP Service, ICP RAID Navigator, ICP Mail, SNMP and ICP RAID Console (ICPCON)

Driver for Windows 2000/XP and ICP RAID Console (ICPCON) for ICP Cluster Controllers

[Version]
Signature="$WINDOWS NT$"
Class=System
ClassGuid={4D36E97D-E325-11CE-BFC1-08002BE10318}
Provider=%MGMT%
DriverVer=07/13/2002,5.3.3.0
CatalogFile=mgmt.cat

[ControlFlags]
ExcludeFromSelect = *

[SourceDisksNames]
1 = %FLOPPY1_DESCRIPTION%,icp.tag,,

[SourceDisksFiles]

[MgtFiles]
;
; Dummy section to satisfy ChkInf tool
;
[DestinationDirs]
DefaultDestDir = 12
[Manufacturer]
%MGMT% = MGMT

[MGMT]
%SCSI\ProcessorIOCTL_-_Device__________.DeviceDesc% = NODRV, SCSI\ProcessorIOCTL_-_Device__________
[NODRV]
;
; Dummy directive to satisfy ChkInf tool
;
CopyFiles = MgtFiles

[NODRV.Services]
;
; this is blank to just allow the install to succeed
;
AddService = , %SPSVCINST_ASSOCSERVICE% ; null service install

[strings]
MGMT = "ICP vortex Computersysteme GmbH"
SCSI\ProcessorIOCTL_-_Device__________.DeviceDesc = "Controller Management Device"
FLOPPY1_DESCRIPTION = "Controller Management Device"

;*******************************************
;Handy macro substitutions (non-localizable)
SPSVCINST_ASSOCSERVICE = 0x00000002

Plug-In for the Intel® Landesk Server Manager v6.0