Keydata Keynote 8320 - Green 732 Télécharger Pilotes et Manuel

The best kind of AC power source to connect your Notebook to is a UPS (Uninterruptible Power Supply). Lacking this, use a power strip with a built-in surge protector. Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery.
Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry.
Turning On Your Notebook Computer
Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The Power-On Self Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows ME, Windows 2000…. etc) is installed, it should start automatically.
To turn the Notebook off, save your work and close all open applications, click on Start, then Shut Down and select Shut down the computer and click "Yes" or press the power button for 4-6 seconds.
Operating on Battery Power
Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions:

Please read these safety instructions carefully.
Please keep this User's Manual for later reference.
Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible.
Please keep this equipment from humidity.
Lay this equipment on a reliable surface when installed. A drop or fall could cause injury.
Make sure to use the right voltage for the power source when connecting the
equipment to the power outlet.
Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage.
Never pour any liquid into the opening, this could cause fire or electrical shock.
Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel.
If on the following situations arises, get the equipment checked by a service personnel:
The Power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work according to the user's manual.
The equipment has dropped and damaged.
If the equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned, storage temperature above 60°C (140°f), it may damage the equipment.
The unit can be operated at an ambient temperature of max. 35°C.
The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A).
Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection.
• The cord set must be approved for the country in which it is used.
• The appliance coupler must have a configuration for mating with a CEE22/EN6032/IEC 320 appliance inlet.

Driver & Application Installation/Removal Procedure For Avance AC'97 Codec:
=====================

<<< For Win98SE/Win2000/WinME/WinXP (WDM driver) >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

Step 1. Before installing the Avance AC'97 Drivers & Applications, Press the
[Cancel] button if Windows detect the PCI Multimedia Audio device.

Step 2. Insert the "Avance AC'97 Drivers & Applications" CD into the CD-ROM
drive and run the setup.exe program to finish the installation.

Step 3. Click on [Next/OK/Go] to continue the procedure. If the Windows popup
"Digital Signature Not Found" message, press [Yes] to continue the
installation.

Step 4. Finally, select to restart the system and press [Finish] to complete
the installation.

The system will reload the drivers and do some adjustments in the INF
file if so required.

--------------------------
Update Driver/Application:
--------------------------

Step 1. Follow Step 2,3,4 described in [Setup at first time] above to complete
the procedure.

--------------------------
Remove Driver/Application:
--------------------------

Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Add/Remove Programs] icon.

Step 3. Select "Avance AC'97 Drivers and Applications" and press [Change/Remove]
button.

Step 4. Click on [Next/OK/Go] to finish the uninstallation.

Step 5. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.
<<< For Win98 Gold (First Edition) >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

The same procedure in Win98SE/Win2000/WinME/WinXP.

--------------------------
Update Driver/Application:
--------------------------

The same procedure in Win98SE/Win2000/WinME/WinXP.

--------------------------
Remove Driver/Application:
--------------------------

The same procedure in Win98SE/Win2000/WinME/WinXP.

<<< For WinNT 4.0 (NT4 driver) >>>